FRF503G

FRF501G - FRF507G Isolated 5.0 AMPS. Glass Passivated Fast Recovery Rectifiers ITO-220AB Features G lass passivated chip junction. H igh efficiency, Low VF H igh current capability H igh reliability H igh surge current capability L ow power loss M echanical Data C ases: ITO-220AB molded plastic E poxy: UL 94V-0 rate flame retardant T erminals: Pure tin plated, Lead free. Leads solderable per MIL-STD-202, Method 208 guaranteed P olarity: As marked H igh temperature soldering guaranteed: o 260 C /10 seconds 0.25”,(6.35mm) from case. M ounting position: Any W eight: 2.24 grams M ounting torque: 5 in – 1bs. max. Dimensions in inches and (millimeters) M aximum Ratings and Electrical Characteristics R ating at 25 oC ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% T ype Number M aximum Recurrent Peak Reverse Voltage M aximum RMS Voltage M aximum DC Blocking Voltage M aximum Average Forward Rectified Current See Fig. 1 P eak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) M aximum Instantaneous Forward Voltage @2.5A M aximum DC Reverse Current o @T C =25 C at Rated DC Blocking Voltage o @ T C =125 C M aximum Reverse Recovery Time (Note1) T ypical Junction Capacitance ( Note 2 ) T ypical Thermal Resistance ( Note 3 ) S ymbol FRF FRF FRF FRF FRF FRF FRF U nits 501G 502G 503G 504G 505G 506G 507G V RRM 50 100 200 400 600 800 1000 V V RMS 35 70 140 280 420 560 700 V V DC 50 100 200 400 600 800 1000 V I(AV) IFSM VF IR T rr Cj 5 .0 30 1 .5 5 .0 100 150 250 1 40 4 .0 - 65 to +150 500 A A V uA uA nS pF o C/W o C R θJC O perating and Storage Temperature Range T J, T STG 1. Reverse Recovery Test Conditions: I F =0.5A, I R =1.0A, I RR =0.25A N otes: 2. Measured at 1MHz and Applied Reverse Voltage of 4.0 Volts D.C. 3. Mount on Heatsink Size 2” x 3” x 0.25” Al-Plate. Version: A06 RATINGS AND CHARACTERISTIC CURVES (FRF501G THRU FRF507G) FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE FIG.2- TYPICAL REVERSE CHARACTERISTICS PER LEG 1000 5 AVERAGE FORWARD CURRENT. (A) INSTANTANEOUS REVERSE CURRENT. ( A) 4 3 100 2 Tj=125 0C 10 1 0 0 50 100 o 150 LEAD TEMPERATURE. ( C) 1.0 Tj=25 0C 30 FIG.3- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PER LEG 0.1 PEAK FORWARD SURGE CURRENT. (A) 0 20 40 60 80 100 120 140 25 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 20 8.3ms Single Half Sine Wave JEDEC Method 15 10 5 0 1 2 5 10 20 50 100 8.0 4.0 NUMBER OF CYCLES AT 60Hz FIG.5- TYPICAL FORWARD CHARACTERISTICS PER LEG FIG.4- TYPICAL JUNCTION CAPACITANCE PER LEG 300 INSTANTANEOUS FORWARD CURRENT. (A) 2.0 1.0 250 CAPACITANCE.(pF) 200 0.4 0.2 0.1 150 100 Tj=25 0C f=1.0MHz Vsig=50mVp-p 0.04 0.02 0.01 0.8 Tj=25oC Pulse Width=300 s 1% Duty Cycle 0.9 1.0 1.1 1.2 1.3 1.4 1.5 50 0 0.1 0.5 1.0 5 10 50 100 500 1000 REVERSE VOLTAGE. (V) INSTANTANEOUS FORWARD VOLTAGE. (V) FIG.6- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50W NONINDUCTIVE 10W NONINDUCTIVE +0.5A (-) DUT (+) 50Vdc (approx) (-) PULSE GENERATOR (NOTE 2) 1W NON INDUCTIVE OSCILLOSCOPE (NOTE 1) (+) 0 -0.25A trr NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms -1.0A 1cm SET TIME BASE FOR 5/ 10ns/ cm Version: A06