GBLA06

GBLA005 THRU GBLA10 Single Phase 4.0 AMPS. Glass Passivated Bridge Rectifiers Voltage Range 50 to 1000 Volts Current 4.0 Amperes Features Glass passivated chip junction Ideal for printed circuit board High case dielectric strength Plastic material has Underwriters Laboratory Flammability Classification 94V-0 Typical IR less than 0.1µA High surge current capability High temperature soldering guaranteed: 260OC / 10 seconds / .375”, (9.5mm) lead lengths. C2.5 GBL .799(20.3) .776(19.7) .146(3.70) .130(3.30) .445(11.3) .421(10.7) .106(2.70) .091(2.30) .067(1.70) .051(1.30) .043(1.10) .035(0.90) .106(2.70) .091(2.30) .047(1.20) .031(0.80) .551(14.0) .512(13.0) .024(0.60) .016(0.40) Mechanical Data Case: Molded plastic body. Terminals: Plated leads solderable per MIL-STD-750, Method 2026. Weight: 0. 071 ounce, 2.0 grams Mounting position: Any 1 2 205(5.20) 189(4.80) 3 4 .205(5.20) .205(5.20) .189(4.80) .189(4.80) 1 2 3 4 Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25+ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Symbol GBLA GBLA GBLA GBLA GBLA GBLA GBLA Units Type Number 005 01 02 04 06 08 10 Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current @TC = 50+ (Note 1) @TA = 40+ (Note 2) Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) TJ=150+ Maximum Instantaneous Forward Voltage @ 4.0A Maximum DC Reverse Current @ TA=25+ at Rated DC Blocking Voltage @ TA=125+ Typical Thermal Resistance Per Leg (Note 1) (Note 2) VRRM VRMS VDC I(AV) 50 35 50 100 70 100 200 140 200 400 280 400 4.0 3.0 600 420 600 800 560 800 1000 700 1000 V V V A A V uA uA +/W + + IFSM VF IR R JA R JL TJ TSTG 120 1.0 5.0 500 47 10 -55 to +150 -55 to + 150 Operating Temperature Range Storage Temperature Range Notes 1. Unit Mounted on 3.0 x 3.0 x 0.11” thick (7.5 x 7.5 x 0.3cm) Al. plate. 2. Units Mounted on P.C.B. 0.5 x 0.5 “ (12x12mm) Copper Pads, 0.375”(9.5mm) Lead Length. REV.1 Oct.-2003 RATINGS AND CHARACTERISTIC CURVES (GBLA005 THRU GBLA10 ) FIG.1- DERATING CURVE FOR OUTPUT RECTIFIED CURRENT 5.0 FIG.2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PER LEG 120 AVERAGE FORWARD RECTIFIED CURRENT. (A) 60 Hz Resistive or Inductive Load 4.0 Heat-Sink Mounting 3.0 x 3.0 x 0.11" Thick (7.5 x 7.5 x0.3cm) Aluminum Substrate PEAK FORWARD SURGE CURRENT. (A) Ta=40 C Single Half Sine-Wave (JEDEC Method) 100 3.0 2.0 50 1.0 P.C.B. Mounting 0.47 x 0.47" (12 x 12mm) Copper pads with 0.375" (9.5mm) lead length 0 50 100 O 1 Cycle 0 150 1 10 NUMBER OF CYCLES 100 0 AMBIENT TEMPERATURE. ( C) FIG.3- TYPICAL FORWARD VOLTAGE CHARACTERISTICS PER LEG INSTANTANEOUS REVERSE LEAKAGE CURRENT. (mA) 100 FIG.4- TYPICAL REVERSE LEAKAGE CHARACTERISTICS PER LEG 500 INSTANTANEOUS FORWARD CURRENT. (A) 100 10 10 Tj=125 0C 1 1 50 600 400V 1000V 0.1 0.1 Tj=25 0C Tj=25 C Pulse Width=300ms 1% Duty Cycle 0.01 0.4 0.01 0.6 0.8 1.0 1.2 INSTANTANEOUS FORWARD VOLTAGE. (V) 1.4 1.6 0 80 20 40 60 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 100 FIG.5- TYPICAL JUNCTION CAPACTITANCE PER LEG 1000 100 FIG.6- TYPICAL TRANSIENT THERMAL CHARACTERISTICS TRANSIENT THERMAL IMPEDANCE ( C/W) 100 Tj=25 C JUNCTION CAPACITANCE (pF) f = 1 MHz Vsig = 50mVp-p 10 100 1 50 600 10 0.1 400V 1000V 1 10 REVERSE VOLTAGE. (V) 0.1 0.01 0.1 1 T, HEATING TIME (SEC.) 10 100