HERF1603G

HERF1601G - HERF1608G Isolated 16.0 AMPS. Glass Passivated High Efficient Rectifiers ITO-220AB Features G lass passivated chip junction. H igh efficiency, Low VF H igh current capability H igh reliability H igh surge current capability For use in low voltage, high frequency inventor, free wheeling, and polarity protection application. M echanical Data C ases: ITO-220AB molded plastic E poxy: UL 94V0 rate flame retardant T erminals: Pure tin plated, lead free, solderable per MIL-STD-202, Method 208 guaranteed P olarity: As marked H igh temperature soldering guaranteed: o 260 C/ 0.25” (6.35mm) from case for 10 seconds Mounting torque: 5 in – 1bs. max. W eight: 2.24 grams Dimensions in inches and (millimeters) R ating at 25 C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% M aximum Ratings and Electrical Characteristics o T ype Number M aximum Recurrent Peak Reverse Voltage M aximum RMS Voltage M aximum DC Blocking Voltage M aximum Average Forward Rectified Current o @TC = 100 C P eak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) M aximum Instantaneous Forward Voltage @8.0A M aximum DC Reverse Current o @T A=25 C at Rated DC Blocking Voltage @ T A=125 oC Typical Reverse Recovery Time ( Note 1 ) Typical Junction Capacitance Operating Temperature Range ( Note 2 ) Typical Thermal Resistance (Note 3) S ymbol V RRM V RMS V DC I(AV) IFSM VF IR Trr HERF HERF HERF HERF HERF HERF HERF HERF 1601G 1602G 1603G 1604G 1605G 1606G 1607G 1608G U nits V V V A A 50 35 50 100 70 100 200 140 200 300 210 300 400 280 400 600 420 600 800 1000 560 700 800 1000 16 125 1.0 1.3 10 400 50 80 1.5 -65 to +150 -65 to +150 80 50 1.7 V uA uA nS pF o C/W o C o C Cj R θJC TJ S torage Temperature Range T STG 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A N otes: 2. Measured at 1 MHz and Applied Reverse Voltage of 4.0V D.C. 3. Mounted on Heatsink Size of 4 in x 6 in x 0.25 in Al-Plate. Version: A06 RATINGS AND CHARACTERISTIC CURVES (HERF1601G THRU HERF1608G) AVERAGE FORWARD CURRENT. (A) FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE 20 16 12 8 4 0 0 50 CASE TEMPERATURE. ( C) o FIG.2- TYPICAL REVERSE CHARACTERISTICS PER LEG 1000 INSTANTANEOUS REVERSE CURRENT. ( A) 100 Tj=125 0C 10 100 150 Tj=25 0C PEAK FORWARD SURGE CURRENT. (A) FIG.3- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PER LEG 150 120 90 60 30 0 1 Tj=25 0C 8.3ms Single Half Sine Wave JEDEC Method 1 0.1 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) FIG.5- TYPICAL FORWARD CHARACTERISTICS PER LEG 100 2 5 10 20 50 100 INSTANTANEOUS FORWARD CURRENT. (A) 30 10 HE RF 16 01 G~ HE RF 16 04 G NUMBER OF CYCLES AT 60Hz G 05 16 RF HE FIG.4- TYPICAL JUNCTION CAPACITANCE PER LEG 240 200 CAPACITANCE.(pF) 120 HE RF 16 01 G~ HE 80 HE RF RF 16 160 05 6G G ~H 40 ER F1 608 G 0 1 2 5 10 20 0.1 0.03 0.01 0.4 H 160 0.3 ER F1 Tj=25 0C 60 6G 1.0 ~H ER F1 Tj=25 C PULSE WIDTH-300 S 1% DUTY CYCLE 0 50 100 200 500 1000 0.6 0.8 1.0 60 3.0 1.2 8G 1.4 1.6 1.8 REVERSE VOLTAGE. (V) FORWARD VOLTAGE. (V) FIG.6- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50 NONINDUCTIVE 10 NONINDUCTIVE trr +0.5A DUT (-) PULSE GENERATOR (NOTE 2) NON INDUCTIVE OSCILLOSCOPE (NOTE 1) (+) 0 -0.25A (+) 50Vdc (approx) (-) NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms -1.0A 1cm SET TIME BASE FOR 5/ 10ns/ cm Version: A06