P600M

P600A THRU P600M 6.0 AMPS Silicon Rectifiers Voltage Range 50 to 1000 Volts Current 6.0 Amperes Features Plastic material used carries Underwriters Laboratory Classification 94V-0 High forward current capability High surge current capability High temperature soldering guaranteed: 260oC/10 seconds, 0.375”(9.5mm) lead length, 5lbs. (2.3kg) tension P600 Mechanical Data Cases: Molded plastic Lead: Plated axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting position: Any Weight: 0.07 ounce, 2.1 grams Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Type Number Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current at o TA=60 C, 0.375”(9.5mm) Lead Length (Fig 1) TL=60℃, 0.125”(3.1mm) Lead Length (Fig 2) Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @6.0A @100A Maximum DC Reverse Current @ TA=25℃ at Rated DC Blocking Voltage @ TA=100℃ Typical Junction Capacitance ( Note 1 ) Typical Thermal Resistance (Note 2) Operating Junction and Storage Temperature Range Symbol P600A P600B P600D P600G P600J P600K P600M Units V V V A A VRRM VRMS VDC I(AV) IFSM VF IR Cj RθJA RθJL TJ, TSTG 50 35 50 100 70 100 200 140 200 400 280 400 6.0 22.0 400.0 1.0 600 420 600 800 560 800 1000 700 1000 1.3 5.0 1.0 110 35 5.0 -50 to + 150 1.4 V uA mA pF ℃/W ℃ Notes: 1. Measured at 1 MHz and Applied Reverse Voltage of 4.0V D.C. 2. Mount on Cu-Pad Size 16mm x 16mm on P.C.B. - 524 - RATINGS AND CHARACTERISTIC CURVES (P600A THRU P600M) FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE AVERAGE FORWARD CURRENT. (A) AVERAGE FORWARD RECTIFIED CURRENT. (A) 6.0 5.0 4.0 60 Hz RESISTIVE OR INDUCTIVE LOAD GROUND PLANE 1.0 X 1.0" (25.4 X 25.4mm) COPPER SURFACE AREA 0.050"(1.27mm) min. 1.1 x 1.0" (30 x 30mm) COPPER PADS STANDARD P.C.B. MOUNTING 0.375" (9.5mm) LEAD LENGTH ALTERNATE P.C.B. MOUNTING 30 25 20 FIG.2- MAXIMUM FORWARD CURRENT DERATING CURVE L=0.125" (3.18mm) L=0.25" (6.35mm) 60 Hz RESISTIVE OR INDUCTIVE LOAD BOTH LEADS ATTACHED OF HEAT SINKS WITH LENGTH as SHOWN, L 3.0 15 L=0.375" (9.5mm) 10 5 0 2.0 1.0 0 L=0.625" (15.8mm) 0 20 40 60 80 100 120 o 140 160 180 200 0 20 40 60 80 100 120 o 140 160 180 200 AMBIENT TEMPERATURE. ( C) LEAD TEMPERATURE. ( C) FIG.3- TYPICAL REVERSE CHARACTERISTICS 100 100 FIG.4- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS INSTANTANEOUS REVERSE CURRENT MICROAMPERES INSTANTANEOUS FORDWARD CURRENT AMPERES 10 Tj=125 0C 10 Tj=100 0C 1 1 Tj=25 0C 0.1 0.1 Tj=25 C PULSE WIDTH-300 S 1% DUTY CYCLE 0 0.01 0 20 40 60 80 100 120 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 140 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 INSTANTANEOUS FORWARD VOLTAGE, VOLTS PEAK FORWARD SURGE CURRENT AMPERES 600 500 400 300 200 FIG.5- MAXIMUM REPETITIVE FORWARD SURGE CURRENT TRANSIENT THERMAL IMPEDANCE, OC/W 8.3 SINGLE HALF SINE-WAVE (JEDEC METHOD) FIG.6- TYPICAL TRANSIENT THERMAL IMPEDANCE 100 10.0 1 100 0 0.1 1 NUMBER OF CYCLES AT 60 Hz 10 0.1 0.01 0.1 1 T, PULSE DURATION, sec. 10 100 - 525 -