RGP15M

RGP15A THRU RGP15M 1.5 AMPS. Glass Passivated Junction Fast Recovery Rectifiers Voltage Range 50 to 1000 Volts Current 1.5 Amperes Features High temperature metallurgically bonded constructed Plastic material used carries Underwriters Laboratory Classification 94V-0 Glass passivated cavity-free junction Capable of meeting environmental standards of MIL-S-19500 1.5 amperes operation at TA=50oC with no thermal runaway Typical IR less than 0.1 uA High temperature soldering guaranteed: 350℃/10seconds/.375”(9.5mm) lead length at 5 lbs., 2.3 kg tension DO-15 Mechanical Data Cases: JEDEC DO-15 molded plastic over glass body Lead: Plated Axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting position: Any Weight: 0.015 ounce, 0.4 gram Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Symbol RGP RGP RGP Type Number 15A 15B 15D Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current .375” (9.5mm) Lead Length @TA = 55℃ Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 1.5A Maximum Full Load Reverse Current, Full Cycle o Average 0.375”(9.3mm) Lead Length at TA=55 C Maximum DC Reverse Current @ TA=25℃ at Rated DC Blocking Voltage @ TA=150℃ Maximum Reverse Recovery Time ( Note 1 ) Typical Junction Capacitance ( Note 2 ) Typical Thermal Resistance (Note 3) Operating and Storage Temperature Range RGP 15G RGP 15J RGP 15K RGP 15M Units V V V A A V uA uA uA nS pF ℃/W ℃ VRRM VRMS VDC I(AV) IFSM VF HTIR IR Trr Cj RθJA 50 35 50 100 70 100 200 140 200 400 280 400 1.5 50.0 1.3 100 5.0 200 600 420 600 800 560 800 1000 700 1000 150 TJ ,TSTG Notes: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1.0 MHz and Applied VR=4.0 Volts 3. Mount on Cu-Pad Size 10mm x 10mm on P.C.B. 250 15 60 -65 to + 175 500 - 576 - RATINGS AND CHARACTERISTIC CURVES (RGP15A THRU RGP15M) FIG.1- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50W NONINDUCTIVE 10W NONINDUCTIVE +0.5A (-) DUT (+) 50Vdc (approx) (-) PULSE GENERATOR (NOTE 2) 1W NON INDUCTIVE OSCILLOSCOPE (NOTE 1) (+) 0 -0.25A trr NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms -1.0A 1cm SET TIME BASE FOR 5/ 10ns/ cm FIG.2- MAXIMUM FORWARD CURRENT DERATING CURVE AVERAGE FORWARD CURRENT. (A) 1.5 1.25 1.0 0.75 0.5 0.25 0 25 50 75 100 o FIG.5- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 10 RESISTIVE OR INDUCTIVE LOAD INSTANTANEOUS FORWARD CURRENT. (A) 1 0.375" (9.5mm) LEAD LENGTH 125 150 175 AMBIENT TEMPERATURE. ( C) 0.1 PEAK FORWARD SURGE CURRENT. (A) FIG.3- MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 50 40 30 20 10 Tj=Tj max. 8.3ms Single Half Sine Wave JEDEC Method Tj=25 C PULSE WIDTH-300 S 1% DUTY CYCLE 0.01 0.4 0.6 0.8 1.0 1.2 FORWARD VOLTAGE. (V) 1.4 1.6 0 FIG.6- TYPICAL REVERSE CHARACTERISTICS 20 10 Tj=125 0C 0 1 10 NUMBER OF CYCLES AT 60Hz 100 FIG.4- TYPICAL JUNCTION CAPACITANCE 100 INSTANTANEOUS REVERSE CURRENT. ( A) 1 Tj=75 0C JUNCTION CAPACITANCE.(pF) Tj=25 0C f=1.0MHz Vsig=50mVp-p 0.1 Tj=25 0C 10 1 1 10 REVERSE VOLTAGE. (V) 100 0.01 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) - 577 -