RS2BA

RS2AA - RS2MA 1.5 AMPS. Surface Mount Fast Recovery Rectifiers SMA/DO-214AC Features For surface mounted application Glass passivated junction chip Built-in strain relief, ideal for automated placement Plastic material used carries Underwriters Laboratory Classification 94V-0 Fast switching for high efficiency High temperature soldering: o 260 C / 10 seconds at terminals Mechanical Data Cases: Molded plastic Terminals: Pure tin plated, Lead free. Polarity: Indicated by cathode band Packing: 12mm tape per EIA STD RS-481 Weight: 0.064 gram Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25 oC ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Type Number Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current See Fig. 1 @TL=100oC Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 1.5A Maximum DC Reverse Current @ TA =25oC at Rated DC Blocking Voltage @ TA=125oC Maximum Reverse Recovery Time ( Note 1 ) Typical Junction Capacitance ( Note 2 ) Symbol RS RS RS RS RS RS RS Units 2AA 2BA 2DA 2GA 2JA 2KA 2MA VRRM 50 100 200 400 600 800 1000 V VRMS 35 70 140 280 420 560 700 V VDC 50 100 200 400 600 800 1000 V I(AV) IFSM VF IR Trr Cj RθJA R θJL 150 1.5 50 1.3 5 200 A A V uA uA nS pF 250 500 50 Typical Thermal Resistance ( Note 3 ) 55 o C /W 18 o Operating Temperature Range TJ -55 to +150 C o Storage Temperature Range TSTG -55 to +150 C 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A Notes: 2. Measured at 1 MHz and Applied VR=4.0 Volts 3. Thermal Resistance from Junction to Ambient and Junction to Lead Mounted on P.C.B. with 0.2”x0.2” ( 5.0 x 5.0 mm ) Copper Pad Areas. - 360 - Version: B07 RATINGS AND CHARACTERISTIC CURVES (RS2AA THRU RS2MA) FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE 2 100 FIG.2- TYPICAL REVERSE CHARACTERISTICS AVERAGE FORWARD CURRENT. (A) 1.5 RESISTIVE OR INDUCTIVE LOAD INSTANTANEOUS REVERSE CURRENT. ( A) Tj=125 0C 1.0 10 0.5 P.C.B. MOUNTED 0.2 X 0.2" (5.0X5.0mm) COPPER PAD AREAS 0 50 60 70 80 90 100 110 120 130 o LEAD TEMPERATURE. ( C) 140 150 160 1 50 FIG.3- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT TL=90OC 8.3ms Single Half Sine Wave JEDEC Method 0.1 0 20 40 60 80 Tj=25 0C PEAK FORWARD SURGE CURRENT. (A) 100 120 140 40 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 30 20 FIG.5- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER LEG 20 10 10 0 NUMBER OF CYCLES AT 60Hz INSTANTANEOUS FORWARD CURRENT. (A) 1 10 100 FIG.4- TYPICAL JUNCTION CAPACITANCE 90 Tj=25 0C f=1.0MHz Vsig=50mVp-p Tj=25 0C 1 JUNCTION CAPACITANCE.(pF) 50 0.1 Pulse Width=300 s 1% Duty Cycle 10 1 5 10 REVERSE VOLTAGE. (V) 50 100 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 FORWARD VOLTAGE. (V) FIG.6- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50W NONINDUCTIVE 10W NONINDUCTIVE +0.5A (-) DUT (+) 50Vdc (approx) (-) PULSE GENERATOR (NOTE 2) 1W NON INDUCTIVE OSCILLOSCOPE (NOTE 1) (+) 0 -0.25A trr NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms -1.0A 1cm SET TIME BASE FOR 5/ 10ns/ cm Version: B07