RS2M

RS2A THRU RS2M 2.0 AMPS. Fast Recovery Surface Mount Rectifiers Voltage Range 50 to1000 Volts Current 2.0 Amperes Features For surface mounted application Glass passivated junction chip Built-in strain relief, ideal for automated placement Plastic material used carries Underwriters Laboratory Classification 94V-O Fast switching for high efficiency High temperature soldering: 260℃/ 10 seconds at terminals .082(2.08) .076(1.93) SMB/DO-214AA .147(3.73) .137(3.48) .187(4.75) .167(4.25) .012(.31) .006(.15) Mechanical Data Cases: Molded plastic Terminals: Solder plated Polarity: Indicated by cathode band Packing: 12mm tape per E1A STD RS-481 Weight: 0.093 gram .103(2.61) .078(1.99) .012(.31) .006(.15) .056(1.41) .035(0.90) .208(5.28) .200(5.08) .008(.20) .004(.10) Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Symbol RS RS RS Type Number 2A 2B 2D Maximum Recurrent Peak Reverse Voltage VRRM 50 100 200 Maximum RMS Voltage VRMS 35 70 140 Maximum DC Blocking Voltage VDC 50 100 200 Maximum Average Forward Rectified Current See Fig. 1 @TL=100OC Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 2.0A Maximum DC Reverse Current @ TA =25℃ at Rated DC Blocking Voltage @ TA=125℃ Maximum Reverse Recovery Time ( Note 1 ) Typical Junction Capacitance ( Note 2 ) Typical Thermal Resistance (Note 3) Operating Temperature Range Storage Temperature Range RS 2G 400 280 400 2.0 50 1.3 5 200 RS 2J 600 420 600 RS RS 2K 2M 800 1000 560 700 800 1000 Units V V V A A V uA uA nS pF ℃/W ℃/W ℃ ℃ I(AV) IFSM VF IR Trr Cj RθJA RθJL TJ TSTG 150 250 50 55.0 18.0 -55 to +150 -55 to +150 500 Notes: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1 MHz and Applied VR=4.0 Volts 3. Thermal Resistance from Junction to Ambient and Junction to Lead Mounted on P.C.B . with 0.4”x0.4” ( 10 x 10 mm ) Copper Pad Areas. - 388 - RATINGS AND CHARACTERISTIC CURVES (RS2A THRU RS2M) FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE PEAK FORWARD SURGE CURRENT. (A) 2.25 FIG.2- MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 50 TL=100 0C 8.3ms Single Half Sine Wave JEDEC Method AVERAGE FORWARD CURRENT. (A) 2.0 RESISTIVE OR INDUCTIVE LOAD 40 30 1.5 20 1.0 P.C.B. MOUNTED 0.27 X 0.27" (7.0X7.0mm) COPPER PAD AREAS 0.5 50 60 70 80 90 100 110 120 o 10 0 130 140 150 160 1 10 NUMBER OF CYCLES AT 60Hz 100 LEAD TEMPERATURE. ( C) FIG.3- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 20 10 FIG.4- TYPICAL REVERSE CHARACTERISTICS 100 INSTANTANEOUS FORWARD CURRENT. (A) Pulse Width=300 s 1% Duty Cycle 1 Tj=25 C 0 INSTANTANEOUS REVERSE CURRENT. ( A) Tj=125 0C 10 0.1 1 Tj=25 0C 0.01 0.4 0.1 0.6 0.8 1.0 1.2 1.4 1.6 1.8 0 20 40 60 80 100 120 140 FORWARD VOLTAGE. (V) PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) FIG.5- TYPICAL JUNCTION CAPACITANCE 90 Tj=25 0C f=1.0MHz Vsig=50mVp-p JUNCTION CAPACITANCE.(pF) 50 10 1 5 10 REVERSE VOLTAGE. (V) 50 100 - 389 -