S2AA_1

S2AA - S2MA 1.5 AMPS. Surface Mount Rectifiers SMA/DO-214AC Features F or surface mounted application G lass passivated junction chip. L ow forward voltage drop H igh current capability E asy pick and place H igh surge current capability P lastic material used carries Underwriters Laboratory Classification 94V-0 H igh temperature soldering: 260 oC / 10 seconds at terminals M echanical Data C ase: Molded plastic T erminals: Pure tin plated, lead free. P olarity: Indicated by cathode band P ackaging: 12mm tape per EIA STD RS-481 W eight: 0.064 gram Dimensions in inches and (millimeters) M aximum Ratings and Electrical Characteristics R ating at 25 oC a mbient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% T ype Number M aximum Recurrent Peak Reverse Voltage M aximum RMS Voltage M aximum DC Blocking Voltage M aximum Avera g e Forward Rectified Current @T L = 100 oC P eak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) M aximum Instantaneous Forward Voltage @ 1.5A M aximum DC Reverse Current @T A = 25 oC at Rated DC Blocking Voltage @ T A=125 oC M aximum Reverse Recovery Time ( Note 1 ) T ypical Junction Capacitance ( Note 2 ) T ypical Thermal resistance (Note 3) O perating Temperature Range S ymbol S 2AA S 2BA S 2DA S 2GA S 2JA S 2KA S 2MA U nits V RRM V RMS V DC I(AV) IFSM VF IR 50 35 50 100 70 100 200 140 200 400 280 400 1 .5 50 1 .1 5 .0 125 2 .0 30 16 53 -55 to +150 -55 to +150 600 420 600 800 560 800 1000 700 1000 V V V A A V uA uA uS pF o T rr Cj R θJL R θJA TJ C/W o o S torage Temperature Range T STG 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A N otes: 2. Measured at 1 MHz and Applied V R=4.0 Volts 3. Measured on P.C. Board with 0.2” x 0.2” (5.0 mm x 5.0mm) Copper Pad Areas. C C - 460 - Version: B07 RATINGS AND CHARACTERISTIC CURVES (S2AA THRU S2MA) FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE 2.0 FIG.2- TYPICAL REVERSE CHARACTERISTICS 10 AVERAGE FORWARD CURRENT. (A) 1.5 1.0 INSTANTANEOUS REVERSE CURRENT. ( A) Tj=125 0C 1 Tj=100 0C 0.5 SINGLE PHASE HALF SIZE WAVE 60Hz RESISTIVE OR INDUCTIVE LOAD 5.0mm2 PAD AREAS 0 50 0.1 60 70 80 90 100 110 120 o LEAD TEMPERATURE. ( C) 130 140 150 155 FIG.3- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 50 Tj=25 0C PEAK FORWARD SURGE CURRENT. (A) 40 8.3ms Single Half Sine Wave JEDEC Method 0.01 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 30 20 FIG.5- TYPICAL FORWARD CHARACTERISTICS 10 10 0 FIG.4- TYPICAL JUNCTION CAPACITANCE 100 60 INSTANTANEOUS FORWARD CURRENT. (A) 1 10 NUMBER OF CYCLES AT 60Hz 100 1 JUNCTION CAPACITANCE.(pF) 40 20 10 6 4 2 1 0.1 Tj=25 0C f=1.0MHz Vsig=50mVp-p 0.1 Tj=25 C PULSE WIDTH-300 S 2% DUTY CYCLE 0.01 0.4 0 0.2 0.4 1 2 4 10 20 40 100 0.6 0.8 1.0 1.2 1.4 1.6 REVERSE VOLTAGE. (V) FORWARD VOLTAGE. (V) FIG.6- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50W NONINDUCTIVE 10W NONINDUCTIVE +0.5A (-) DUT (+) 50Vdc (approx) (-) PULSE GENERATOR (NOTE 2) 1W NON INDUCTIVE OSCILLOSCOPE (NOTE 1) (+) 0 -0.25A trr NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms -1.0A 1cm SET TIME BASE FOR 5/ 10ns/ cm Version: B07