S2G

S2A THRU S2M 2.0 AMPS. Surface Mount Rectifiers Voltage Range 50 to 1000 Volts Current 2.0 Amperes Features For surface mounted application Glass passivated junction chip. Low forward voltage drop High current capability Easy pick and place High surge current capability Plastic material used carries Underwriters Laboratory Classification 94V-O High temperature soldering: 260oC / 10 seconds at terminals .082(2.08) .076(1.93) SMB/DO-214AA .147(3.73) .137(3.48) .187(4.75) .167(4.25) .012(.31) .006(.15) Mechanical Data Case: Molded plastic Terminals: Solder plated Polarity: Indicated by cathode band Packaging: 12mm tape per EIA STD RS-481 Weight: 0.093 gram .103(2.61) .078(1.99) .012(.31) .006(.15) .056(1.41) .035(0.90) .208(5.28) .200(5.08) .008(.20) .004(.10) Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Type Number Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current @TL =100℃ Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 2.0A Maximum DC Reverse Current @ TA =25℃ at Rated DC Blocking Voltage @ TA=125℃ Typical Thermal Resistance (Note 3) Maximum Reverse Recovery Time ( Note 1 ) Typical Junction Capacitance ( Note 2 ) Operating Temperature Range Storage Temperature Range Symbol S2A S2B S2D S2G S2J S2K S2M Units VRRM VRMS VDC I(AV) IFSM VF IR RθJL RθJA Trr Cj TJ 50 35 50 100 70 100 200 140 200 400 280 400 2.0 50 1.15 600 420 600 800 1000 560 700 800 1000 V V V A A V uA uA ℃/W uS pF ℃ ℃ TSTG Notes: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1 MHz and Applied VR=4.0 Volts 3. Measured on P.C. Board with 0.4 x 0.4” (10 x 10mm) Copper Pad Areas. 5.0 125 16 53 2.0 30 -55 to +150 -55 to +150 - 484 - RATINGS AND CHARACTERISTIC CURVES (S2A THRU S2M) FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE 50 2.0 FIG.2- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT. (A) 8.3ms Single Half Sine Wave JEDEC Method AVERAGE FORWARD CURRENT. (A) 40 1.5 30 20 1.0 SINGLE PHASE HALF SIZE WAVE 60Hz RESISTIVE OR INDUCTIVE LOAD 7.0mm2 PAD AREAS 10 0.5 50 0 60 70 80 90 100 110 o 120 130 140 150 155 1 10 NUMBER OF CYCLES AT 60Hz 100 LEAD TEMPERATURE. ( C) FIG.3- TYPICAL FORWARD CHARACTERISTICS 10 FIG.4- TYPICAL REVERSE CHARACTERISTICS 10 Tj=125 0C INSTANTANEOUS FORWARD CURRENT. (A) INSTANTANEOUS REVERSE CURRENT. ( A) 1 1 Tj=100 0C 0.1 0.1 Tj=25 C PULSE WIDTH-300 S 2% DUTY CYCLE 0.01 0.4 0 Tj=25 0C 0.01 0.6 0.8 1.0 1.2 1.4 1.6 0 20 40 60 80 100 120 140 FORWARD VOLTAGE. (V) PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) FIG.5- TYPICAL JUNCTION CAPACITANCE 100 60 JUNCTION CAPACITANCE.(pF) 40 20 10 6 4 2 1 0.1 Tj=25 0C f=1.0MHz Vsig=50mVp-p 0.2 0.4 1 2 4 10 20 40 100 REVERSE VOLTAGE. (V) - 485 -