S2JA

S2AA THRU S2MA 1.5 AMPS. Surface Mount Rectifiers Voltage Range 50 to 1000 Volts Current 1.5 Amperes Features For surface mounted application Glass passivated junction chip. Low forward voltage drop High current capability Easy pick and place High surge current capability Plastic material used carries Underwriters Laboratory Classification 94V-O High temperature soldering: 260oC / 10 seconds at terminals SMA/DO-214AC .062(1.58) .050(1.27) .111(2.83) .090(2.29) .187(4.75) .160(4.06) Mechanical Data Case: Molded plastic Terminals: Solder plated Polarity: Indicated by cathode band Packaging: 12mm tape per EIA STD RS-481 Weight: 0.064 gram .091(2.30) .078(1.99) .012(.31) .006(.15) .008(.20) .004(.10) .210(5.33) .195(4.95) .056(1.41) .035(0.90) Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Symbol S2AA S2BA Type Number Maximum Recurrent Peak Reverse Voltage VRRM 50 100 Maximum RMS Voltage VRMS 35 70 Maximum DC Blocking Voltage VDC 50 100 Maximum Average Forward Rectified Current @TL =100OC Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 1.5A Maximum DC Reverse Current @ TA =25OC at Rated DC Blocking Voltage @ TA=125OC Typical Thermal Resistance (Note 3) Maximum Reverse Recovery Time ( Note 1 ) Typical Junction Capacitance ( Note 2 ) Operating Temperature Range S2DA S2GA S2JA S2KA S2MA 200 140 200 400 280 400 1.5 50 1.1 5.0 125 16 53 2.0 600 420 600 800 1000 560 700 800 1000 Units V V V A A V uA uA O I(AV) IFSM VF IR RθJL RθJA Trr C/W uS pF C O C O Cj 30 TJ -55 to +150 Storage Temperature Range TSTG -55 to +150 Notes: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1 MHz and Applied VR=4.0 Volts 3. Measured on P.C. Board with 0.2 x 0.2” (5.0 x 5.0mm) Copper Pad Areas. - 496 - RATINGS AND CHARACTERISTIC CURVES (S2AA THRU S2MA) FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE PEAK FORWARD SURGE CURRENT. (A) 2.0 50 8.3ms Single Half Sine Wave JEDEC Method FIG.2- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT AVERAGE FORWARD CURRENT. (A) 1.5 40 1.0 30 20 0.5 SINGLE PHASE HALF SIZE WAVE 60Hz RESISTIVE OR INDUCTIVE LOAD 7.0mm2 PAD AREAS 10 0 50 0 60 70 80 90 100 110 120 o LEAD TEMPERATURE. ( C) 130 140 150 155 1 10 NUMBER OF CYCLES AT 60Hz 100 FIG.3- TYPICAL FORWARD CHARACTERISTICS 10 FIG.4- TYPICAL REVERSE CHARACTERISTICS 10 Tj=125 0C INSTANTANEOUS FORWARD CURRENT. (A) INSTANTANEOUS REVERSE CURRENT. ( A) 1 1 Tj=100 0C 0.1 0.1 Tj=25 C PULSE WIDTH-300 S 2% DUTY CYCLE 0.01 0.4 0 Tj=25 0C 0.01 0.6 0.8 1.0 1.2 1.4 1.6 0 FORWARD VOLTAGE. (V) 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) FIG.5- TYPICAL JUNCTION CAPACITANCE 100 60 JUNCTION CAPACITANCE.(pF) 40 20 10 6 4 2 1 0.1 Tj=25 0C f=1.0MHz Vsig=50mVp-p 0.2 0.4 1 2 4 10 20 40 100 REVERSE VOLTAGE. (V) - 497 -