SF1007G

SF1001G THRU SF1008G 10.0 AMPS. Glass Passivated Super Fast Rectifiers Voltage Range 50 to 600 Volts Current 10.0 Amperes Features Low forward voltage drop High current capability High reliability High surge current capability TO-220 Mechanical Data Case: Molded plastic Epoxy: UL 94V-O rate flame retardant Terminals: Leads solderable per MIL-STD202, Method 208 guaranteed Polarity: As marked High temperature soldering guaranteed: 260oC/10 seconds .16”,(4.06mm) from case. Weight: 2.24 grams PIN 1 PIN 3 Positive CT CASE PIN 2 Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% SF SF SF Symbol SF Type Number Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current .375 (9.5mm) Lead Length @TC = 100℃ Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 5.0A Maximum DC Reverse Current @ TA=25℃at Rated DC Blocking Voltage @ TA=100℃ Maximum Reverse Recovery Time (Note 1) Typical Junction Capacitance (Note 2) Typical Thermal Resistance (Note 3) SF SF SF SF 1001G 1002G 1003G 1004G 1005G 1006G 1007G 1008G Units V V V A A VRRM VRMS VDC I(AV) IFSM VF IR Trr Cj RθJC 50 35 50 100 150 200 300 400 500 600 70 105 140 210 280 350 420 100 150 200 300 400 500 600 10.0 125 0.975 10.0 400 35 70 50 1.3 1.7 V uA uA nS pF ℃/W ℃ ℃ 3.5 Operating Temperature Range TJ -65 to +150 Storage Temperature Range TSTG -65 to +150 Notes: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1 MHz and Applied Reverse Voltage of 4.0 V D.C. 3. Mounted on Heatsink Size of 2 in x 3 in x 0.25 in Al-plate. - 272 - RATINGS AND CHARACTERISTIC CURVES (SF1001G THRU SF1008G) FIG.1- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50W NONINDUCTIVE 10W NONINDUCTIVE +0.5A (-) DUT (+) 50Vdc (approx) (-) PULSE GENERATOR (NOTE 2) 1W NON INDUCTIVE OSCILLOSCOPE (NOTE 1) (+) 0 -0.25A trr NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms -1.0A 1cm SET TIME BASE FOR 5/ 10ns/ cm FIG.2- MAXIMUM FORWARD CURRENT DERATING CURVE AVERAGE FORWARD CURRENT. (A) 20 16 12 8 4 0 FIG.3- TYPICAL REVERSE CHARACTERISTICS 1000 INSTANTANEOUS REVERSE CURRENT. ( A) 100 TJ=100 0C 10 TJ=75 0C 0 50 CASE TEMPERATURE. ( C) o 100 150 PEAK FORWARD SURGE CURRENT. (A) 150 120 FIG.4- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PER LEG TJ=125 0C 8.3ms Single Half Sine Wave JEDEC Method 1 TJ=25 0C 0.1 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 90 60 30 FIG.6- TYPICAL FORWARD CHARACTERISTICS PER LEG 100 INSTANTANEOUS FORWARD CURRENT. (A) 0 30 10 01 G 10 F1 F1 NUMBER OF CYCLES AT 60Hz 00 4G 1 2 5 10 20 50 100 00 6G 3 1 100 Tj=25 C 0 90 CAPACITANCE.(pF) 80 0.3 0.1 70 60 50 40 0.03 0.01 0.4 SF FIG.5- TYPICAL JUNCTION CAPACITANCE PER LEG SF 10 8G 00 F1 ~S G 07 10 SF G 05 ~S ~S 4G 00 F1 ~S 8G G 00 01 F1 10 ~S SF G 05 10 SF Tj=25oC Pulse Width=300 s 1% Duty Cycle 1 2 5 10 20 50 100 200 500 1000 0.6 0.8 1.0 1.2 1.4 1.6 1.8 REVERSE VOLTAGE. (V) FORWARD VOLTAGE. (V) - 273 -