SF3006PT

SF3001PT THRU SF3006PT 30.0 AMPS. Glass Passivated Super Fast Rectifiers Voltage Range 50 to 400 Volts Current 30.0 Amperes TO-3P/TO-247AD Features Dual rectifier construction, positive center-tap Plastic package has Underwriters Laboratory Flammability Classifications 94V-0 Glass passivated chip junctions Superfast recovery time, high voltage Low forward voltage, high current capability Low thermal resistance Low power loss, high efficiency High temperature soldering guaranteed: 260oC / 10 seconds, 0.16”(4.06mm) lead lengths at 5 lbs., (2.3kg) tesion Mechanical Data Cases: JEDEC TO-3P/TO-247AD molded plastic Terminals: Leads solderable per MIL-STD-750, Method 2026 Polarity: As marked Mounting position: Any Weight: 0.2 ounce, 5.6 grams PIN 1 PIN 3 PIN 2 Positive CT Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% TYPE NUMBER Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current at Tc=100℃ Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @15.0A Maximum D.C. Reverse Current at Rated DC Blocking Voltage @ Tc=25℃ @ Tc=100℃ Symbol VRRM VRMS VDC I(AV) IFSM VF IR SF SF SF SF SF SF 3001PT 3002PT 3003PT 3004PT 3005PT 3006PT Units V V V A A 50 35 50 100 70 100 150 105 150 30 300 200 140 200 300 210 300 400 280 400 0.95 1.3 10.0 500 Maximum Reverse Recovery Time(Note 2) TJ=25℃ 35 Trr 175.0 Typical Junction Capacitance (Note 1) Cj RθJC 2.5 Typical Thermal Resistance (Note 3) TJ -55 to +150 Operating Junction Temperature Range TSTG -55 to +150 Storage Temperature Range Notes: 1. Measured at 1 MHz and Applied Reverse Voltage of 4.0V D.C. 2. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, Recover to 0.25A. 3. Mounted on 4” x 6” x 0.25” Al-Plate. V uA uA nS pF ℃ /W ℃ ℃ - 294 - RATINGS AND CHARACTERISTIC CURVES (SF3001PT THRU SF3006PT) FIG.1- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50W NONINDUCTIVE 10W NONINDUCTIVE +0.5A (-) DUT (+) 50Vdc (approx) (-) PULSE GENERATOR (NOTE 2) 1W NON INDUCTIVE OSCILLOSCOPE (NOTE 1) (+) 0 -0.25A trr NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms -1.0A 1cm SET TIME BASE FOR 5/ 10ns/ cm FIG.2- MAXIMUM FORWARD CURRENT DERATING CURVE AVERAGE FORWARD CURRENT. (A) FIG.4- TYPICAL REVERSE CHARACTERISTICS PER LEG 1000 36 30 24 12 6 0 INSTANTANEOUS REVERSE CURRENT MICRO AMPERES 100 TJ=100 0C TJ=75 0C 10 0 50 100 o 150 CASE TEMPERATURE. ( C) PEAK FORWARD SURGE CURRENT. (A) 300 250 FIG.3- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PER LEG 1 TJ=25 0C 0.1 8.3ms Single Half Sine Wave JEDEC Method Tj=Tj max. 200 150 100 50 0 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) FIG.6- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER LEG 40 SF3001PT-04PT 1 2 5 10 20 50 100 INSTANTANEOUS FORWARD CURRENT. (A) 20 10 NUMBER OF CYCLES AT 60Hz FIG.5- TYPICAL JUNCTION CAPACITANCE PER LEG 1000 500 CAPACITANCE.(pF) 4 SF3005PT-06PT 1 125 0C 25 0C 200 100 50 20 10 0.1 Tj=25oC f=1MHz Vsig=50mVp-p 0.4 Pulse Width=300 s 2% Duty Cycle 0.1 1 5 10 50 100 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 0.5 FORWARD VOLTAGE. (V) REVERSE VOLTAGE. (V) - 295 -