SFA801G

SFA801G - SFA808G 8.0 AMPS. Glass Passivated Super Fast Rectifiers TO-220AC .185(4.70) .175(4.44) .412(10.5) MAX .113(2.87) .103(2.62) DIA .154(3.91) .148(3.74) .27(6.86) .23(5.84) .594(15.1) .587(14.9) PIN1 .16(4.06) .14(3.56) .56(14.22) .53(13.46) .037(0.94) .027(0.68) 2 .11(2.79) .10(2.54) .055(1.40) .045(1.14) Features H igh efficiency, low VF H igh current capability H igh reliability H igh surge current capability L ow power loss. F or use in low voltage, high frequency inventor, free wheeling, and polarity protection application M echanical Data C ases: TO-220AC Molded plastic E poxy: UL 94V-0 rate flame retardant T erminals: Pure tin plated, lead free. solderable per MIL-STD-202, Method 208 guaranteed P olarity: As marked H igh temperature soldering guaranteed: 260 oC/10 seconds/.16”,(4.06mm) from case. W eight: 2.24 grams .205(5.20) .195(4.95) .025(0.64) .014(0.35) PIN 1 PIN 2 CASE Dimensions in inches and (millimeters) R ating at 25 oC ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% T ype Number M aximum Recurrent Peak Reverse Voltage M aximum RMS Voltage M aximum DC Blocking Voltage M aximum Average Forward Rectified o Current @T C = 1 00 C P eak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) M aximum Instantaneous Forward Voltage @ 8.0A M aximum DC Reverse Current @ T A =25 oC at Rated DC Blocking Voltage @ T A =100 oC M aximum Reverse Recovery Time (Note 1) T ypical Junction Capacitance (Note 2) T ypical Thermal Resistance (Note 3) Operating Temperature Range S torage Temperature Range N otes: M aximum Ratings and Electrical Characteristics S ymbol SFA SFA SFA V RRM V RMS V DC I(AV) IFSM VF IR T rr 0 .975 50 35 50 100 70 100 150 405 150 SFA SFA SFA SFA SFA 801G 802G 803G 804G 805G 806G 807G 808G U nits V V V A A 200 140 200 300 210 300 400 280 400 500 350 500 600 420 600 8 .0 1 25 1.3 10 400 35 1 00 60 4 .0 -65 to +150 -65 to +150 o 1.7 V uA uA nS pF C/W o C o C Cj R θJC TJ T STG 1. Reverse Recovery Test Conditions: IF =0.5A, IR =1.0A, IRR =0.25A 2. Measured at 1 MHz and Applied Reverse Voltage of 4.0 V D.C. 3. Mounted on Heatsink Size of 2” x 3” x 0.25” Al-Plate. Version: A06 RATINGS AND CHARACTERISTIC CURVES (SFA801G THRU SFA808G) FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE INSTANTANEOUS REVERSE CURRENT. ( A) FIG.2- TYPICAL REVERSE CHARACTERISTICS 1000 AVERAGE FORWARD CURRENT. (A) 10 8 6 4 2 0 100 TJ=100 0C TJ=75 0C 10 0 50 CASE TEMPERATURE. ( C) o 100 150 PEAK FORWARD SURGE CURRENT. (A) 150 120 FIG.3- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT TJ=125 0C 8.3ms Single Half Sine Wave JEDEC Method 1 TJ=25 0C 0.1 0 20 40 60 80 100 120 140 90 60 30 0 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) FIG.5- TYPICAL FORWARD CHARACTERISTICS 100 30 A8 SF 06 G 1 2 5 10 20 50 100 INSTANTANEOUS FORWARD CURRENT. (A) NUMBER OF CYCLES AT 60Hz 10 FA 8 A SF 04 G 5 80 G~ 100 Tj=25 C 0 1 90 CAPACITANCE.(pF) 80 70 60 50 40 1 2 5 0.3 0.1 0.03 SF A8 01 3 G~ S FIG.4- TYPICAL JUNCTION CAPACITANCE 10 20 50 100 200 500 1000 0.01 0.4 0.6 0.8 1.0 SF A8 07 G ~S FA 80 8G Tj=25oC Pulse Width=300 s 1% Duty Cycle A8 SF 01 G ~S 8 FA 04 50 NONINDUCTIVE FIG.6- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 10 NONINDUCTIVE trr +0.5A DUT (-) PULSE GENERATOR (NOTE 2) NON INDUCTIVE OSCILLOSCOPE (NOTE 1) (+) 0 -0.25A A8 SF (+) 50Vdc (approx) (-) G NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms 05 G ~S REVERSE VOLTAGE. (V) 8 FA 08 G 1.2 1.4 1.6 1.8 FORWARD VOLTAGE. (V) -1.0A 1cm SET TIME BASE FOR 5/ 10ns/ cm Version: A06