SFF1006G

SFF1001G - SFF1008G Isolation 10.0 AMPS. Glass Passivated Super Fast Rectifiers ITO-220AB Features H igh efficiency, low VF H igh current capability H igh reliability H igh surge current capability L ow power loss. F or use in low voltage, high frequency inventor, free wheeling, and polarity protection application M echanical Data C ase: ITO-220AB molded plastic E poxy: UL 94V-0 rate flame retardant T erminals: Pure tin plated, lead free. solderable per MIL-STD-202, Method 208 guaranteed P olarity: As marked H igh temperature soldering guaranteed: o 260 C/10 seconds.16”,(4.06mm) from case. W eight: 2.24 grams M ounting torque: 5 in – 1bs. max. Dimensions in inches and (millimeters) M aximum Ratings and Electrical Characteristics R ating at 25 oC a mbient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% S ymbol S FF SFF SFF T ype Number M aximum Recurrent Peak Reverse Voltage M aximum RMS Voltage M aximum DC Blocking Voltage M aximum Average Forward Rectified Current .375 (9.5mm) Lead Length o @T C = 1 00 C P eak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) M aximum Instantaneous Forward Voltage @ 5.0A M aximum DC Reverse Current o @ T A=25 C at Rated DC Blocking Voltage @ T A=100 oC M aximum Reverse Recovery Time (Note 1) T ypical Junction Capacitance (Note 2) T ypical Thermal Resistance (Note 3) O perating Temperature Range SFF SFF SFF SFF SFF 1001G 1002G 1003G 1004G 1005G 1006G 1007G 1008G Units V V V A A V RRM V RMS V DC I(AV) IFSM VF IR T rr 50 35 50 100 70 100 150 105 150 200 140 200 10 300 210 300 400 280 400 500 350 500 600 420 600 1 25 0 .975 10 400 35 70 2 .0 -65 to +150 50 o 1.3 1.7 V uA uA nS pF C/W o C o C Cj R θJC TJ S torage Temperature Range T STG -65 to +150 1. Reverse Recovery Test Conditions: IF=0.5A, IR =1.0A, IRR =0.25A N otes: 2. Measured at 1 MHz and Applied Reverse Voltage of 4.0 V D.C. 3. Mounted on Heatsink Size of 2” x 3” x 0.25” Al-plate. Version: A06 RATINGS AND CHARACTERISTIC CURVES (SFF1001G THRU SFF1008G) FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE AVERAGE FORWARD CURRENT. (A) 20 16 12 8 4 0 FIG.2- TYPICAL REVERSE CHARACTERISTICS 1000 INSTANTANEOUS REVERSE CURRENT. ( A) 100 TJ=100 0C 10 TJ=75 0C 0 50 CASE TEMPERATURE. ( C) o 100 150 PEAK FORWARD SURGE CURRENT. (A) 150 120 FIG.3- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PER LEG TJ=125 0C 8.3ms Single Half Sine Wave JEDEC Method 1 TJ=25 0C 0.1 0 20 40 60 80 100 120 140 90 60 30 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) FIG.5- TYPICAL FORWARD CHARACTERISTICS PER LEG 100 INSTANTANEOUS FORWARD CURRENT. (A) ~S NUMBER OF CYCLES AT 60Hz 10 00 F1 FF 1G ~S FF 10 06 G SF FIG.4- TYPICAL JUNCTION CAPACITANCE PER LEG 100 Tj=25 0C 10 0 1 30 04 G 2 5 10 20 50 100 G 3 1 00 5 SF F1 90 SF F1 00 7 S G~ FF 10 08 G CAPACITANCE.(pF) 80 0.3 0.1 SF F1 70 60 50 40 SF F1 00 5G 1 2 1G 00 ~S FF 04 10 50 NONINDUCTIVE 0.03 0.01 0.4 0.6 0.8 1.0 Tj=25oC Pulse Width=300 s 1% Duty Cycle FIG.6- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 10 NONINDUCTIVE trr +0.5A DUT (-) PULSE GENERATOR (NOTE 2) NON INDUCTIVE OSCILLOSCOPE (NOTE 1) (+) 0 -0.25A ~S FF 10 08 G 5 10 (+) 50Vdc (approx) (-) REVERSE VOLTAGE. (V) NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms G 20 50 100 200 500 1000 -1.0A 1cm 1.2 1.4 1.6 1.8 FORWARD VOLTAGE. (V) SET TIME BASE FOR 5/ 10ns/ cm Version: A06