TS1117BCW

TS1117B 800mA Low Dropout Positive Voltage Regulator Pin assignment: 1. Gnd/Adj 8.N/C 2. 3. Out 6. 7. Out 4. Input 5. N/C Pin assignment: 1. Gnd/Adj 2. Output 3. Input Low Dropout Voltage 1.3V max. General Description The TS1117B Series are high performance positive voltage regulators are designed for use in applications requiring low dropout performance at full rated current, Additionally, the TS1117B Series provides excellent regulation over variations due to changes in line, load and temperature. Outstanding features include low dropout performance at rated current, fast transient response, internal current limiting and thermal shutdown protection of the output device. The TS1117B Series are three terminal regulators with fixed and adjustable voltage options available in popular packages. This series is offered in 3-pin TO-252 SOT-223 and 8-pin SOP package. Features Low dropout performance 1.3V max. Full current rating over line and temperature. Fast transient response ±2%Total output regulation over line, load and temperature Adjust pin current 90uA (typ.) Line regulation typical 0.015%. Load regulation typical 0.05%. Fixed/adjustable output voltage TO-252 SOT-223 and SOP-8 package Block Diagram Ordering Information Part No. TS1117BCS xx TS1117BCP xx -20 ~ +85 C o Operating Temp. (Junction) Package SOP-8 TO-252 TS1117BCW xx SOT-223 Note: Where xx denotes voltage option, 50= 5.0V 33= 3.3V 25= 2.5V 18= 1.8V Leave blank for adjustable version. Absolute Maximum Rating Input Supply Voltage Operation Input Supply Voltage Power Dissipation Operating Junction Temperature Range Storage Temperature Range Lead Soldering Temperature (260 C) o Vin Vin (opt. Typ.) PD TJ TSTG 15 12 Internally Limited -20 ~ +125 -65 ~ +150 5 V V W o o C C S TS1117B 1-6 2003/12 rev. D Electrical Characteristics Ta = 25 oC, unless otherwise specified. Adjustable version test with Vout = 2.5V. Parameter Output Voltage Conditions Vout+1.5V ≤Vin≤ 12V, Io=10mA Vout+1.5V ≤Vin≤ 12V, Io=800mA (Vin-out) =1.5V, Io=10mA (Vin-out) =1.5V, Io=800mA Min 0.990|Vo| 0.980|Vo| 0.990|Vo| 0.980|Vo| -- Typ 5.0 / 3.3 2.5 / 1.8 1.25 -0.015 0.05 1.0 8 90 -0.5 60 Max 1.010|Vo| 1.020|Vo| 1.010|Vo| 1.020|Vo| 12 0.3 1.0 1.3 10 ---70 Unit V V V V V % % % V mA uA A % dB Reference Voltage Input Supply Voltage Line Regulation Load Regulation (note 1,2) Dropout Voltage Minimum Load Current Adjustable Pin Current Current Limit Temperature Stability Ripple Rejection Vout+1.5V ≤ Vin ≤ 12V, Io=10mA Vin=Vout+1.5V, 10mA ≤ Io ≤ 800mA Io=800mA, ∆Vout=1%Vout Vin=5V ------ Vin - Vout=3V Io=10mA F = 120Hz, Io=1A Cout=25uF, Vin=Vout + 3V 1.1 --- Thermal Performance Condition Thermal Resistance Junction to Ambient Package type TO-252 SOP-8 SOT-223 Typ 90 160 165 Unit o C/W Note 1: See thermal regulation specification for changes in output voltage due to heating effects. Line and load regulation are measured at a constant junction temperature by low duty cycle pulse testing. Load regulation is measured at the output lead = 1/18” from the package. Note 2: Line and load regulation are guaranteed up to the maximum power dissipation of 15W. Power dissipation is determined by the input / output voltage difference and the output current. Guaranteed maximum power dissipation will not be available over the full input / output voltage range. Note 3: Quiescent current is defined as the minimum output current required to maintain the regulation. TS1117B 2-6 2003/12 rev. D Typical Application Circuit Fixed output voltage version Vout = Vref * (1 + R2 / R1) * Cin is requested if regulator is located Far from power supply filter ** Design Cout as close to Vout pin as possible Adjustable output voltage version TS1117B 3-6 2003/12 rev. D Electrical Characteristics Curve Figure 1: dropout voltage v.s. output current Figure 2: load regulation v.s. temp. Figure 3: output change v.s. temp. Figure 4: line regulation Figure 5: line transient response Figure 6: load transient response TS1117B 4-6 2003/12 rev. D TO-252 Mechanical Drawing J A E F DIM A B C D E F G I B TO-252 DIMENSION MILLIMETERS INCHES MIN MAX MIN MAX 6.570 6.840 0.259 0.269 9.250 10.400 0.364 0.409 0.550 0.700 0.022 0.028 2.560 2.670 0.101 0.105 2.300 2.390 0.090 0.094 0.490 0.570 0.019 0.022 1.460 1.580 0.057 0.062 0.520 5.340 1.460 0.570 5.550 1.640 0.020 0.210 0.057 0.022 0.219 0.065 G D C H H I J SOT-223 Mechanical Drawing A B I DIM A B SOT-223 DIMENSION MILLIMETERS INCHES MIN MAX MIN MAX 6.350 6.850 0.250 0.270 2.900 3.100 0.114 0.122 3.450 0.595 4.550 2.250 0.835 6.700 0.250 10° 1.550 3.750 0.635 4.650 2.350 1.035 7.300 0.355 16° 1.800 0.136 0.023 0.179 0.088 0.032 0.263 0.010 10° 0.061 0.148 0.025 0.183 0.093 0.041 0.287 0.014 16° 0.071 H C J K F G E D C D E F G H I J K TS1117B 5-6 2003/12 rev. D SOP-8 Mechanical Drawing A DIM SOP-8 DIMENSION MILLIMETERS INCHES MIN MAX MIN MAX 4.80 5.00 0.189 0.196 3.80 4.00 0.150 0.157 1.35 1.75 0.054 0.068 0.35 0.49 0.014 0.019 0.40 1.25 0.016 0.049 1.27 (typ) 0.05 (typ) 0.10 0.25 0.004 0.009 0o 7o 0o 7o 5.80 6.20 0.229 0.244 0.25 0.50 0.010 0.019 16 9 B P 1 8 G C D K M R F A B C D F G K M P R TS1117B 6-6 2003/12 rev. D