TS1117SCP

TS1117S 800mA Low Dropout Positive Voltage Regulator TO-220 TO-263 TO-252 SOT -223 Low Dropout Voltage 1.5V max Pin assignment: 1. Ground / Adj 2. Output 3. Input General Description The TS1117S Series are high performance positive voltage regulators a re designed fo r use in applications requiring low dropout performance at full rated current, Additionally, the T S1117S Series provides excellent regulation over variations due to changes in line, load and te mperature . Outstanding fe atures include low dropout perfo rmance a t rated current, fast transient response, in ternal current lim iting and thermal shutdown protection of the output device. The TS1117S Se ries are three term inal regulators w ith fixed and adjustable voltage options available in popular packages. This series is offered in 3-pin TO-263, TO-220, TO-252 and S OT-223 package. Features     Low dropout perfo rmance 1.5V max . Full curren t ra ting over line and temperatu re. Fast transient response ±2%Total output regulation over line, load and temperature    Adjust pin current max 90 μA over temperatu re Line regulation typical 0.015%. Load regulation typical 0.05%. Fixed/adjustable output voltage TO-220, TO-263 T O-252 and SOT -223 package   Block Diagram Ordering Information Part No . TS1117SCZ-xx TS1117SCM-xx TS1117SCP-xx TS1117SCW-xx -20 ~ +85 C o Operating Te mp. (Ambient) Pa c k a ge TO-220 TO-263 TO-252 SOT-223 Note: Where xx denotes voltage option, available are 5.0V, 3.3V , 2.5V and 1.8V. Leave blank for adjustable version. Contac t facto ry for additional voltage options. Absolute Maximum Rating Input Supply Voltage Operation Input Supply Voltage Power Dissipation Operating Junction Tempera ture Range Storage Temperatu re Range Lead Soldering Temperature (260 C) TO-220 / TO -263 Package TO-252 / SOT -223 Package 10 5 S o Vin (max.) Vin (opr., Typ.) PD TJ TSTG 12 7 Internally Limited -25 ~ +150 -65 ~ +150 V V W o o C C TS1117S 1 -6 2005/11 rev. A Electrical Characteristics Ta = 25 C, unless otherw ise specified. Ad justable version test with Vout = 2.5V. o Parameter Output Voltage Reference Voltage Input Supply Voltage Line Regulation Load Regulation (note 1 ,2) Dropout Voltage Minimum Load Current Adjustable Pin Cu rrent Current L imit Temperature S tability Ripple Rejection Conditions Vout+1.5V ≤ Vin ≤ 7V, Io=800mA (Vin-out) =1.5V , Io=800mA Min 0.980|Vo| 0.980|Vo| -- Typ 5.0 / 3 .3 2.5 / 1 .8 1.25 -0.015 0.05 1.3 8 90 -0.5 60 Max 1.020|Vo| 1.020|Vo| 7 0.2 1.0 1.5 10 ---70 Unit V V V % % % V mA uA A % dB Vout+1.5V ≤ Vin ≤ 7V, Io=10mA Vin=Vout+1.5V, 10mA ≤ Io ≤ 800mA Io=1A, ∆Vout=1%Vout Vin=5V ------ Vin - Vout=3V Io=10mA F = 120Hz, Io=1A Cout=25uF, Vin=Vout + 3V 0.9 --- Thermal Performance Condition Package type TO-220 Thermal Resistance Junction to Ambient TO-263 TO-252 SOT-223 Typ 85 85 105 110 Unit o C/W Note 1: See therma l regula tion specification fo r changes in o utput voltage due to heating e ffects. Line and load regulation are measured at a constant junction temperature by low duty cycle pulse testing. Load regulation is measured at the output lead = 1/18” from the package. Note 2: Line and load regulation are guaranteed up to the maximum power dissipation of 15W. Power dissipation is determined by the input / output voltage diffe rence and the output current. Guaranteed maximum power dissipation will not be available over the fu ll input / output voltage range. Note 3: Qu iescent current is defined as the m inimum output c urrent required to main tain the regulation. TS1117S 2 -6 2005/11 rev. A Typical Application Circuit Fixed output voltage version Vout = Vref * (1 + R2 / R1) * Cin is requested if regulator is located Far from power supply filter ** Design Cout as close to Vout pin as possible Adjustable output voltage version TS1117S 3 -6 2005/11 rev. A Electrical Characteristics Curve Fi gure 1: dr opout voltage v.s. output current Fi gure 2: l oad regul ati on v.s. temp. Fi gure 3: output change v.s. temp. Fi gure 4: li ne regulation Fi gure 5: li ne transient response Fi gure 6: l oad tr ansient response TS1117S 4 -6 2005/11 rev. A TO-220 Mechanical Drawing A B A C B C K L K L DIM A B C D MIN TO-220 DIMENS ION MILLIMETERS MA X 10.500 4.440 2.940 6.350 1.106 2.715 5.430 14.732 9.017 16.510 4.826 1.397 29.620 2.921 0.610 6.858 10.000 3.240 2.440 0.381 2.345 4.690 12.700 8.382 14.224 3.556 0.508 27.700 2.032 0.255 5.842 INCHES MIN 0.394 0.128 0.096 0.015 0.092 0.092 0.500 0.330 0.560 0.140 0.020 1.060 0.080 0.010 0.230 MA X 0.413 0.175 0.116 0.250 0.040 0.058 0.107 0.581 0.355 0.650 0.190 0.055 1.230 0.115 0.024 0.270 P J I P J I M D E F GM H I J K L M N D F G TS1117S H A D H E F G E O N O N O P TO-263 Mechanical Drawing E A I H B B I H F E F DIM A B C D E F G H I J MIN TO-263 DIMENS ION MILLIMETERS MA X 10.500 15.875 0.991 2.660 4.830 1.400 0.730 8.800 1.400 1.520 10.000 14.605 0.508 2.420 4.064 1.118 0.450 8.280 1.140 1.480 INCHES MIN 0.394 0.575 0.020 0.095 0.160 0.045 0.018 0.325 0.044 0.058 MA X 0.413 0.625 0.039 0.105 0.190 0.055 0.029 0.346 0.055 0.060 G C D G C 5 -6 2005/11 rev. A TO-252 Mechanical Drawing J AA J E E F F IM D A B C D E F G MIN 6.570 9.250 0.550 2.560 2.300 0.490 1.460 0.520 5.340 1.460 TO-252 DIMENS ION MILLIMETERS MA X 6.840 10.400 0.700 2.670 2.390 0.570 1.580 0.570 5.550 1.640 INCHES MIN 0.259 0.364 0.022 0.101 0.090 0.019 0.057 0.020 0.210 0.057 MA X 0.269 0.409 0.028 0.105 0.094 0.022 0.062 0.022 0.219 0.065 I BB I G DD CC H H GH I J SOT-223 Mechanical Drawing A B A SOT-223 DIMENS ION B I I DIM A B MILLIMETERS MIN 6.350 2.900 3.450 0.595 4.550 2.250 0.835 6.700 0.250 10° 1.550 MA X 6.850 3.100 3.750 0.635 4.650 2.350 1.035 7.300 0.355 16° 1.800 INCHES MIN 0.250 0.114 0.136 0.023 0.179 0.088 0.032 0.263 0.010 10° 0.061 MA X 0.270 0.122 0.148 0.025 0.183 0.093 0.041 0.287 0.014 16° 0.071 H H C C C J J D E F G H I J K K F G G F K D D E E TS1117S 6 -6 2005/11 rev. A