TS29100CW3.3

TS29100/1/2 1.0A Ultra Low Dropout Positive Voltage Regulator Low Dropout Voltage 0.4V typ. Enable Input Control Adjustable Output Error Flag Detection General Description The TS29100/1/2 series are using process with a PNP pass element for high current, high accuracy and low dropout voltage regulators. These regulator s feature 400mV(typ) dropout voltages and very low ground current, these devices also find applications in lower current and low dropout critical systems, where their tiny dropout voltage and ground current values are important attributes. The TS29100/1/2 series are fully protected against over current faults, reversed input polarity, reversed lead insertion, over temperature operation, positive and negative transient voltage spikes, logic level enable control and error flag which signals whenever the output falls out of regulation. On the TS29101 and TS29102, the enable pin may be tied to Vin if it is not required for enable control. This series are offered in 3-pin SOT-223 and 8-pin SOP pacakge. Features Dropout voltage typically 0.4V @Io=1.0A Output current up to 1.0A Low ground current Output voltage trimmed before assembly Extremely fast transient response +60V Transient peak voltage -20V Reverse peak voltage Zero current shutdown mode Error flag signals output out of regulation Internal current limit Thermal shutdown protection Ordering Information Part No. TS29100CWxx TS29101CSxx TS29102CSxx TS29102CS Note: Where xx denotes voltage option, available are 12V, 5.0V, 3.3V and 2.5V. Leave blank for adjustable version. Contact factory for additional voltage options. -40 ~ +125 C SOP-8 o Operating Temp. (Junction) Package SOT-223 Applications Battery power equipment Automotive electronics High efficiency “Green” computer system High efficiency linear power supplies High efficiency post regulator for switching supply Absolute Maximum Rating (Note 1) Input Supply Voltage (Note 2) Operation Input Voltage Power Dissipation (Note 3) Operating Junction Temperature Range Storage Temperature Range Lead Soldering Temperature (260 C) o Vin Vin (operate) PD TJ TSTG -20V ~ +60 26 Internally Limited -40 ~ +125 -65 ~ +150 5 V V W o o C C S TS29100/1/2 1-1 2003/12 rev. A Electrical Characteristics Vin = Vout + 1V, Venable= 2.4V, IL = 10mA, Co = 10uF, Adjustable versions are programmed to 5V output, Ta = 25 oC unless otherwise specified. Parameter Output Voltage Output Voltage Input Supply Voltage Output Voltage Temperature Coefficient Line Regulation Load Regulation Dropout Voltage (Note 4) Conditions 10mA ≤ IL ≤ 1.0A, Vo+1V ≤ Vin ≤ 26V Min 0.990|Vo| 0.980|Vo| --- Typ 12 / 5.0 3.3/ 2.5 -20 0.05 0.2 100 200 400 4 10 2.0 600 400 260 Max 1.010|Vo| 1.020|Vo| 26 100 0.5 1.0 200 Unit V V ppm/ oC % % mV Vo+1V ≤ Vin ≤ 26V 10mA ≤ IL ≤ 1.0A IL=100mA IL=500mA IL=1.0A ------------ 600 -20 ----uVrms A mA Quiescent Current (Note 5) Short Circuit Current (Note 6) Output Noise, 10Hz to 100KHz, IL=100mA IL=500mA IL=1.0A Vout=0 CL=2.2uF CL=10uF CL=33uF Reference (TS29102CS) Reference Voltage Reference Voltage Adjust Pin Bias Current Reference Voltage Temperature Coefficient Adjust Pin Bias Current Temperature Coefficient -0.1 -nA/ oC (Note 7) 10mA ≤ IL ≤ 1.5A, 2.3V ≤ Vin ≤ 26V --40 20 80 -nA ppm/ oC 0.980|Vo| 0.970|Vo| 1.24 1.020|Vo| 1.030|Vo| V Flag Output (TS29101CS) Output Leakage Current Output Low Voltage Upper Threshold Voltage Lower Threshold Voltage Hysteresis VOH=26V Vin=4.5V, IOL=250uA (Note 8) (Note 8) (Note 8) --40 ----60 75 15 2 300 -95 -uA mV mV mV mV Enable Input (TS29101 / TS29102) Input Logic Voltage Enable Pin Input Current Regulator Output Current Shutdown Low (OFF) High (ON) Ven=26V Ven=0.8V Ven ≤ 0.8V, Vin ≤ 26V, Vout=0 -2.4 -------10 0.8 -750 5 500 uA uA V TS29100/1/2 2-2 2003/12 rev. A Thermal Performance Condition Thermal Resistance Junction to Ambient Package type SOT-223 SOP-8 Typ 15 20 Unit o C/W Note 1: Absolute Maximum Rating is limits beyond which damage to the device may occur. For guaranteed specifications and test conditions see the Electrical Characteristics. Note 2: Maximum positive supply voltage of 60V must be limited duration (