TS29152CM5RN

TS29152 1.5A Ultra Low Dropout Voltage Regulator TO-220-5L TO-263-5L 2 (D PAK) Pin Definition: 1. Enable 2. Input 3. Ground 4. Output 5. Adjust General Description TS29152 is using process with a PNP pass element for high current, high accuracy and low dropout voltage regulators. These regulator s feature 350mV(typ) dropout voltages and very low ground current, these devices also find applications in lower current and low dropout critical systems, where their tiny dropout voltage and ground current values are important attributes. TS29152 isfully protected against over current faults, reversed input polarity, reversed lead insertion, over temperature operation, positive and negative transient voltage spikes, logic level enable control and error flag which signals whenever the output falls out of regulation. On the TS29152, the enable pin may be tied to VIN if it is not required for enable control. Features ● ● ● ● ● ● ● ● Dropout voltage typically 0.6V @ Io=1.5A Output Current up to 1.5A Low Ground Current Extremely Fast Transient Response +60V Transient Peak Voltage -20V Reverse Peak Voltage Zero Current Shutdown Mode Current Limit & Thermal Shutdown Protection TM Ordering Information Part No. TS29152CZ5 C0 TS29152CM5 RN Package TO-220-5L TO-263-5L Packing 50pcs / Tube 800pcs / 13” Reel Application ● ● ● ● ● ● PowerPC Power Supplies Battery Powered Equipment Consumer and Personal Electronics High Efficiency Linear Power Supplies High-efficiency Post Regulator for Switching Supply Low-Voltage microcontrollers and Digital Logic Absolute Maximum Rating (Note 1) Parameter Supply Voltage Operation Input Voltage Power Dissipation (Note 4) Operating Junction Temperature Range Storage Temperature Range Lead Soldering Temperature (260 C) o Symbol VIN VIN (operate) PD TJ TSTG Limit -20V ~ +60 26 Internally Limited -40 ~ +125 -65 ~ +150 5 Unit V V W o o C C S 1/1 Version: A09 TS29152 1.5A Ultra Low Dropout Voltage Regulator Thermal Performance Condition Thermal Resistance Junction to Ambient o Package type TO-220-5L TO-263-5L Typ 80 85 Unit o C/W Electrical Characteristics VIN=VOUT+1V, Venable=2.4V, IL=10mA, Co=10uF, Adjustable versions are programmed to 5V output, TJ=25 C unless otherwise specified. Parameter Output Voltage Output Voltage Input Supply Voltage Output Voltage Temperature Coefficient Line Regulation Load Regulation Dropout Voltage (Note 4) Conditions 10mA ≤ IL ≤ 1.5A, Vo+1V ≤ VIN ≤ 26V Min 0.990|Vo| 0.980|Vo| --- Typ VOUT -20 0.05 0 .2 80 200 350 8 22 2.1 600 400 260 Max 1.010|Vo| 1.020|Vo| 26 100 0 .5 1.0 200 -600 --3.5 ---1.020|Vo| Unit V V ppm/ C % % o Vo+1V ≤ VIN ≤ 26V 10mA ≤ IL ≤ 1.5A IL=100mA IL=750mA IL=1.5A IL=750mA IL=1.5A VOUT =0 CL=2.2uF CL=10uF CL=33uF -----------0.980|Vo| mV mA A uVrms Quiescent Current (Note 5) Short Circuit Current (Note 6) Output Noise, 10Hz to 100KHz, IL=100mA Reference Reference Voltage Reference Voltage Adjust Pin Bias Current Reference Voltage Temperature Coefficient Adjust Pin Bias Current Temperature Coefficient Enable Input Input Logic Voltage Enable Pin Input Current Regulator Output Current Shutdown 10mA ≤ IL ≤ 1.5A, 2.3V ≤ VIN ≤ 26V 0.970|Vo| -- 1.24 40 20 0 .1 1.030|Vo| 80 --- V nA ppm/ C nA/ C o o (Note 7) --- Low (OFF) High (ON) VEN =26V VEN =0.8V VEN ≤ 0.8V, VIN ≤ 26V, VOUT =0 -2.4 ---- ----10 0.8 -750 5 500 V uA uA 2/2 Version: A09 TS29152 1.5A Ultra Low Dropout Voltage Regulator Electrical Specification (Continue) Note 1: Absolute Maximum Rating is limits beyond which damage to the device may occur. For guaranteed specifications and test conditions see the Electrical Characteristics. Note 2: Maximum positive supply voltage of 60V must be limited duration (