TS39152CM5

TS39150/1/2/3 1.5A Ultra Low Dropout Voltage Regulator with Multi-Function TO-220 TO-263 2 (D PAK) Pin Definition: TS3 9 1 5 0 1. Input 2. Ground (tab) 3. Output TO-220-5L TO-263-5L 2 (D PAK) Pin Definition: TS3 9 1 5 1 x x TS3 9 1 5 2 1. Enable 1. Enable 2. Input 2. Input 3. Ground 3. Ground 4. Output 4. Output 5. Flag 5. Adjust TS3 9 1 5 3 1. Enable 2. Input 3. Ground 4. Output 5 . Se n s e General Description TS39150/1/2/3 are 1.5A ultra low dropout linear voltage regulators that provide low voltage, high current output fro m an ex tremely s mall package. These regulator offers extremely low dropout ( typically 400mV at 1.5A) and v ery low ground current (typically 12mA at 1.5A). TS39150/1/2/3 are fully protec ted against over current faults, reversed input polarity , reversed lead insertion, over temperature operation, positive and negative transient voltage spikes, logic level enable control and error flag which signals w henever the output falls out of regulation. On the TS39150/1/2/3, the enable pin may be tied to VIN if it is not required for enable control. Features ● ● ● ● ● ● ● ● Dropout voltage typically 0.4V @ Io=1.5A Output Current up to 1.5A L o w Gr o u n d C u r r e n t Extremely Fas t Transient Response Reversed Leakage & Reverse Battery Protection Error Flag Signals Output (TS39101 only) Inter nal Current Limit Thermal Shutdown Protection TM Ordering Information Part No. Package Packi ng TS39150C Zxx C0 TO-220 50pc s / T ube TS39150C Mxx RN TO-263 800pc s / 13” R ee l TS39151C Z5xx C0 TO-220-5L 50pc s / T ube TS39151C M5xx RN TO-263-5L 800pc s / 13” R ee l TS39152C Z5 C 0 TO-220-5L 50pc s / T ube TS39152C M5 RN TO-263-5L 800pc s / 13” R ee l TS39153C Z5xx C0 TO-220-5L 50pc s / T ube TS39153C M5xx RN TO-263-5L 800pc s / 13” R ee l Note: W here xx denotes voltage option, available are 1 5 =1 . 5 V 1 8 =1 . 8 V 2 5 =2 . 5 V 3 3 =3 . 3 V 5 0 =5 . 0 V Contact to factory for addition output voltage option. Application ● ● ● ● ● ● ● Power PC Power Supplies Battery Powered Equipment Consumer and Personal Electr onics High Effic iency Linear Power Supplies SMPS Post Regulator and DC to DC Modules High-efficiency Post Regulator for Switching Supply Low-Voltage microcontrollers and Digital Logic Pin Description Pin Confi guration Enable Input Gr o u n d Output Flag (fixed voltage) Feed Back (adjustable) Pin Descripti on TTL/COMS compatible input. Logic high is enable; logic low or open is shutdown Unregulated input: +16V maximum supply Ground: Ground pin and TAB / heat sink are internally connected. Regulator output Error Flag (output) : Open-collector output. Active low indicates an output fault condition, if no used, leave open. Adjus tment input: Feedback input. Connec t to resistive voltage-divider network. 1/12 Version: A07 TS39150/1/2/3 1.5A Ultra Low Dropout Voltage Regulator with Multi-Function Absolute Maximum Rating (Note 1) Supply Voltage Enable Voltage Storage Temperature Range Lead Soldering Temperature (260 C) ESD o VIN VEN TSTG - 2 0 V ~ +2 0 +2 0 - 6 5 ~ +1 5 0 5 (Note 3) V o V C S Operating Rating (Note 2) Operation Input Voltage Operation Enable Voltage Power Dissipation (Note 4) Operating Junction Temperature R ange VIN (operate) VEN (operate) PD TJ +2.25 ~ +16 +2.25 ~ +16 Inter nally Limited - 4 0 ~ +1 2 5 o V V W o C Electrical Characteristics VIN = VOUT + 1V, VIN =2.5V for fixed refer ence output voltage, Venable= 2.25V, Ta = 25 C, unless otherwise specified. Parameter Fixed Output Voltage Fixed Refer ence Output Voltage Fixed Refer ence Output Voltage Line R egulation Load R egulation Output Voltage Temp. Coefficient Dropout Voltage (Note 5) Conditi ons 10mA ≤ IL ≤ 1.5A, Vo+1V ≤ VIN ≤ 8V IL=10mA 10mA ≤ IL ≤ 1.5A, 2.5V ≤ VIN ≤ 8V IL=10mA, Vo+1V ≤ VIN ≤ 8V VIN =Vout+1V, 10mA≤IL≤1.5A IL=100mA IL=750mA IL=1.5A IL=100mA IL=750mA IL=1.5A Mi n 0.980| Vo| 0.980| Vo| 0.970| Vo| ----------0.980| Vo| 0.970| Vo| ---- Ty p VOUT 1.24 (VREF) 0.05 0.2 40 100 275 400 5 7 25 2.0 Max 1.020| Vo| 1.020| Vo| 1.030| Vo| 0.5 1.0 100 250 350 630 18 20 -2.5 1.020| Vo| 1.030| Vo| 120 --0.8 -75 4 Unit V V % % ppm / C mV o Δ VOUT = -1% Quiescent Current (Note 6) Current Limited VIN= VOUT +1V mA A VOUT=0, VIN =VOUT+1V Refer ence (TS39152) Reference Voltage Reference Voltage Adjus t Pin Bias Current Reference Voltage Temp. C oefficient Adjus t Pin Bias Current Temp. Coefficient (Note 7) (Note 8) 1.24 40 20 0.1 ----V nA o ppm / C nA / C o Enable I nput (TS39151/2/3) Input Logic Voltage Enable Pin Input C urrent Low (OFF) High ( ON) VEN =2.25V VEN =0.8V -2.25 --V uA 2/12 Version: A07 TS39150/1/2/3 1.5A Ultra Low Dropout Voltage Regulator with Multi-Function Electrical Characteristics (Continue) Flag Output (TS39151/3) Output Leakage Current Output Low Voltage (Note 9) Upper Threshold Voltage Lower Threshold Voltage Hysteresis VOH=16V VIN=0.9 * VOUT, IOL=250uA % of VOUT % of VOUT ---93 -----1 2 400 99 --uA mV % % % Thermal Performance Conditi on Thermal R esistance Junction to Case Package type TO-220 / TO-220-5L TO-263 / TO-263-5L Ty p 80 80 Unit o C/W Note 1: Absolute Maximum Rating is limits beyond which damage to the device may occur . For guaranteed specifications and tes t conditions see the Electr ical Characteristics. Note 2: The device is not guaranteed to operate outside its oper ating rating. Note 3: Devices are ESD sensitive. Handling precautions recommended. Note 4: The maximum allowable pow er dissipation is a function of the maximum junction temperature, TJ, the junc tion to ambient ther mal resistance, ӨJA, and the ambient temperature, Ta. Exceeding the maximum allowable power dissipation w ill cause excessive die temperatur e, and the regulator will go into ther mal shutdown. The effec tive value of ӨJA can be r educed by using a heat sink, Pd(max) = (TJ(max) – Ta) / ӨJA. Note 5: Dropout voltage is defined as the input to output differential at w hich the output voltage drops -1% below its nominal v alue measured at 1V differential. Note 6: Ground pin current is the regulator quiescent c urrent. The total current drawn from the source is the sum of the ground pin current and output load current, IGND = IIN - IOUT for fix output voltage, , IGND = IIN - IOUT +10mA for fix reference output voltage in full load regulation. Note 7: VREF ≤ VOUT ≤ (VI N – 1V), 2.25V ≤ VIN ≤ 16V, 10mA ≤ IL ≤ 1.0A. Note 8: Output voltage temperature coefficient is ΔVOUT (worse cast) / (TJ(max) – TJ(MI N)) w here is TJ(max) +125 C and o TJ(MIN) is 0 C . Note 9: For adjustable device and fixed dev ice with VOUT > 2.25V. o 3/12 Version: A07 TS39150/1/2/3 1.5A Ultra Low Dropout Voltage Regulator with Multi-Function Functional Diagram TS39150 Fixed Regulator B lock D iagram TS39151/3 Fixed Regulator with Flag, Sense and Enable B lock D iagram TS39152 Adjustable Regulator B lock D iagram 4/12 Version: A07 TS39150/1/2/3 1.5A Ultra Low Dropout Voltage Regulator with Multi-Function Application Information The TS3915x series are high per formance with low dropout voltage r egulator suitable for moderate to high cur rent and voltage regulator application. Its 630mV dropout voltage at full load and over temperature makes it especially valuable in battery power systems and as high efficiency noise filters in pos t regulator applications. U nlike nor mal N PN transistor design, wher e the base to emitter voltage drop and collector to emitter saturation voltage limit the minimum dropout voltage, dropout perfor mance of the PN P output of these dev ices is limited only by low VCE saturation voltage. The TS3915x series is fully protec ted from damage due to fault conditions. Linear current limiting is provided. Output current during overload conditions is constant. Thermal shutdown the device when the die temperature exc eeds the maximum safe operating temperature. Transient protection allows dev ice survival even when the input voltage spikes above and below nominal. The output struc ture of these regulators allows voltages in excess of the desir ed output voltage to be applied without reverse current flow . Output Capacitor Requirement The TS3915x series requires an output capacitor to maintain stability and impr ove trans ient response is necessary. The value of this capacitor is dependent upon the output current, lower currents allow s maller capacitors. TS3915x series output capacitor selection is dependent upon the ESR of the output capacitor to maintain stability. When the output capacitor is 10uF or greater , the output capacitor should have an ESR less than 2Ω. This w ill improve transient response as well as promote stability. U ltra low ESR capacitors (