TS39150/1/2/3
1.5A Ultra Low Dropout Voltage Regulator with Multi-Function
TO-220 TO-263 2 (D PAK)
Pin Definition: TS39150 1. Input 2. Ground (tab) 3. Output
TO-220-5L
TO-263-5L 2 (D PAK)
Pin Definition: TS39151xx TS39152 1. Enable 1. Enable 2. Input 2. Input 3. Ground 3. Ground 4. Output 4. Output 5. Flag 5. Adjust
TS39153 1. Enable 2. Input 3. Ground 4. Output 5. Sense
General Description
TS39150/1/2/3 are 1.5A ultra low dropout linear voltage regulators that provide low voltage, high current output from an extremely small package. These regulator offers extremely low dropout (typically 400mV at 1.5A) and very low ground current (typically 12mA at 1.5A). TS39150/1/2/3 are fully protected against over current faults, reversed input polarity, reversed lead insertion, over temperature operation, positive and negative transient voltage spikes, logic level enable control and error flag which signals whenever the output falls out of regulation. On the TS39150/1/2/3, the enable pin may be tied to VIN if it is not required for enable control.
Features
● ● ● ● ● ● ● ● Dropout voltage typically 0.4V @ Io=1.5A Output Current up to 1.5A Low Ground Current Extremely Fast Transient Response Reversed Leakage & Reverse Battery Protection Error Flag Signals Output (TS39151 only) Internal Current Limit Thermal Shutdown Protection
TM
Ordering Information
Part No. Package Packing
TS39150CZxx C0 TO-220 50pcs / Tube TS39150CMxx RN TO-263 800pcs / 13” Reel TS39151CZ5xx C0 TO-220-5L 50pcs / Tube TS39151CM5xx RN TO-263-5L 800pcs / 13” Reel TS39152CZ5 C0 TO-220-5L 50pcs / Tube TS39152CM5 RN TO-263-5L 800pcs / 13” Reel TS39153CZ5xx C0 TO-220-5L 50pcs / Tube TS39153CM5xx RN TO-263-5L 800pcs / 13” Reel Note: Where xx denotes voltage option, available are 18=1.8V 25=2.5V 33=3.3V 50=5.0V Contact to factory for addition output voltage option.
Application
● ● ● ● ● ● ● PowerPC Power Supplies Battery Powered Equipment Consumer and Personal Electronics High Efficiency Linear Power Supplies SMPS Post Regulator and DC to DC Modules High-efficiency Post Regulator for Switching Supply Low-Voltage microcontrollers and Digital Logic
Pin Description
Pin Configuration
Enable Input Ground Output Flag (fixed voltage) Feed Back (adjustable)
Pin Description
TTL/COMS compatible input. Logic high is enable; logic low or open is shutdown Unregulated input: +16V maximum supply Ground: Ground pin and TAB / heat sink are internally connected. Regulator output Error Flag (output): Open-collector output. Active low indicates an output fault condition, if no used, leave open. Adjustment input: Feedback input. Connect to resistive voltage-divider network. 1/12 Version: D07
TS39150/1/2/3
1.5A Ultra Low Dropout Voltage Regulator with Multi-Function
Absolute Maximum Rating (Note 1)
Supply Voltage Enable Voltage Storage Temperature Range Lead Soldering Temperature (260 C) ESD
o
VIN VEN TSTG
-20V ~ +20 +20 -65 ~ +150 5 (Note 3)
V
o
V C S
Operating Rating (Note 2)
Operation Input Voltage Operation Enable Voltage Power Dissipation (Note 4) Operating Junction Temperature Range VIN (operate) VEN (operate) PD TJ +2.25 ~ +16 +2.25 ~ +16 Internally Limited -40 ~ +125
o
V V W
o
C
Electrical Characteristics
VIN = VOUT + 1V, VIN =2.5V for fixed reference output voltage, Venable= 2.25V, Ta = 25 C, unless otherwise specified.
Parameter
Fixed Output Voltage Fixed Reference Output Voltage Fixed Reference Output Voltage Line Regulation Load Regulation Output Voltage Temp. Coefficient Dropout Voltage (Note 5)
Conditions
10mA ≤ IL ≤ 1.5A, Vo+1V ≤ VIN ≤ 8V IL=10mA 10mA ≤ IL ≤ 1.5A, 2.5V ≤ VIN ≤ 8V IL=10mA, Vo+1V ≤ VIN ≤ 16V VIN =Vout+1V, 10mA≤IL≤1.5A IL=100mA IL=750mA IL=1.5A IL=100mA IL=750mA IL=1.5A
Min
0.980|Vo| 0.980|Vo| 0.970|Vo| ----------0.980|Vo| 0.970|Vo| ----2.25 ---
Typ
VOUT 1.24 (VREF) 0.05 0 .2 40 100 275 400 5 7 25 2.0
Max
1.020|Vo| 1.020|Vo| 1.030|Vo| 0 .5 1.0 100 250 350 630 18 20 -2.5 1.020|Vo| 1.030|Vo| 120 --0.8 -75 4
Unit
V
V % % ppm/ C mV
o
Δ VOUT = -1%
Quiescent Current (Note 6) Current Limited
VIN= VOUT +1V
mA A
VOUT=0, VIN =VOUT+1V
Reference (TS39152)
Reference Voltage Reference Voltage Adjust Pin Bias Current Reference Voltage Temp. Coefficient Adjust Pin Bias Current Temp. Coefficient (Note 7) (Note 8) 1.24 40 20 0 .1 ----V nA o ppm/ C nA/ C
o
Enable Input (TS39151/2/3)
Input Logic Voltage Enable Pin Input Current Low (OFF) High (ON) VEN =2.25V VEN =0.8V V uA
2/12
Version: D07
TS39150/1/2/3
1.5A Ultra Low Dropout Voltage Regulator with Multi-Function
Electrical Characteristics (Continue)
Flag Output (TS39151/3)
Output Leakage Current Output Low Voltage (Note 9) Upper Threshold Voltage Lower Threshold Voltage Hysteresis VOH=16V VIN=0.9 * VOUT, IOL=250uA % of VOUT % of VOUT ---93 -----1 2 400 99 --uA mV % % %
Thermal Performance
Condition
Thermal Resistance Junction to Case
Package type
TO-220 / TO-220-5L TO-263 / TO-263-5L
Typ
80 80
Unit
o
C/W
Note 1: Absolute Maximum Rating is limits beyond which damage to the device may occur. For guaranteed specifications and test conditions see the Electrical Characteristics. Note 2: The device is not guaranteed to operate outside its operating rating. Note 3: Devices are ESD sensitive. Handling precautions recommended. Note 4: The maximum allowable power dissipation is a function of the maximum junction temperature, TJ, the junction to ambient thermal resistance, ӨJA, and the ambient temperature, Ta. Exceeding the maximum allowable power dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown. The effective value of ӨJA can be reduced by using a heat sink, Pd(max) = (TJ(max) – Ta) / ӨJA. Note 5: Dropout voltage is defined as the input to output differential at which the output voltage drops -1% below its nominal value measured at 1V differential. Note 6: Ground pin current is the regulator quiescent current. The total current drawn from the source is the sum of the ground pin current and output load current, IGND = IIN - IOUT for fix output voltage, , IGND = IIN - IOUT +10mA for fix reference output voltage in full load regulation. Note 7: VREF ≤ VOUT ≤ (VIN – 1V), 2.25V ≤ VIN ≤ 16V, 10mA ≤ IL ≤ 1.0A. Note 8: Output voltage temperature coefficient is ΔVOUT (worse cast) / (TJ(max) – TJ(MIN)) where is TJ(max) +125 C and o TJ(MIN) is 0 C. Note 9: For adjustable device and fixed device with VOUT > 2.25V.
o
3/12
Version: D07
TS39150/1/2/3
1.5A Ultra Low Dropout Voltage Regulator with Multi-Function
Functional Diagram
TS39150 Fixed Regulator Block Diagram
TS39151/3 Fixed Regulator with Flag, Sense and Enable Block Diagram
TS39152 Adjustable Regulator Block Diagram
4/12
Version: D07
TS39150/1/2/3
1.5A Ultra Low Dropout Voltage Regulator with Multi-Function
Application Information
The TS3915x series are high performance with low dropout voltage regulator suitable for moderate to high current and voltage regulator application. Its 630mV dropout voltage at full load and over temperature makes it especially valuable in battery power systems and as high efficiency noise filters in post regulator applications. Unlike normal NPN transistor design, where the base to emitter voltage drop and collector to emitter saturation voltage limit the minimum dropout voltage, dropout performance of the PNP output of these devices is limited only by low VCE saturation voltage. The TS3915x series is fully protected from damage due to fault conditions. Linear current limiting is provided. Output current during overload conditions is constant. Thermal shutdown the device when the die temperature exceeds the maximum safe operating temperature. Transient protection allows device survival even when the input voltage spikes above and below nominal. The output structure of these regulators allows voltages in excess of the desired output voltage to be applied without reverse current flow.
Output Capacitor Requirement
The TS3915x series requires an output capacitor to maintain stability and improve transient response is necessary. The value of this capacitor is dependent upon the output current, lower currents allow smaller capacitors. TS3915x series output capacitor selection is dependent upon the ESR of the output capacitor to maintain stability. When the output capacitor is 10uF or greater, the output capacitor should have an ESR less than 2Ω. This will improve transient response as well as promote stability. Ultra low ESR capacitors (
很抱歉,暂时无法提供与“TS39152CZ5C0”相匹配的价格&库存,您可以联系我们找货
免费人工找货