TS750

TS750 THRU TS758 6.0 AMPS. Silicon Rectifiers Voltage Range 50 to 800 Volts Current 6.0 Amperes Features Plastic material used carries Underwriters Laboratory Classification 94V-0 High forward current capability Diffused junction High surge current capability High temperature soldering guaranteed: 260OC/10 seconds, 0.375”(9.5mm) lead length, 5lbs.(2.3kg) tension P600 Mechanical Data Cases: Molded plastic body Lead: Plated axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting position: Any Weight: 0.07 ounce, 2.1 grams Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Single phase, half wave,60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Symbol TS750 TS751 TS752 TS754 TS756 TS758 Units Type Number Maximum Recurrent Peak Reverse Voltage 50 100 200 400 600 800 V VRRM Maximum RMS Voltage VRMS 35 70 140 280 420 560 V Maximum DC Blocking Voltage VDC 50 100 200 400 600 800 V Maximum Non-repetitive Peak Reverse Voltage VBR 60 120 240 480 720 1200 V Maximum Average Forward Rectified Current at TA = 60℃, P.C.B. Mounting (Fig. 1) TL= 60℃, 0.125”(3.18mm) Lead Length (Fig. 2) Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 6.0A @ 100A Maximum DC Reverse Current @ TA=25℃ at Rated DC Blocking Voltage @ TA=100℃ Typical Junction Capacitance ( Note 1 ) Typical Thermal Resistance (Note 2) Operating Junction Temperature Range Storage Temperature Range I(AV) IFSM VF IR Cj RθJA RθJL TJ TSTG 6.0 22.0 400 0.95 1.25 5.0 1000 150 20.0 4.0 -50 to +150 -50 to +150 A A V uA uA pF ℃/W ℃ ℃ 1.30 Notes: 1. Measured at 1.0 MHz and Applied Reverse Voltage of 4.0 Volts 2. Mount on Cu-Pad Size 16mm x 16mm on P.C.B. - 526 - RATINGS AND CHARACTERISTIC CURVES (TS750 THRU TS758) FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE AVERAGE FORWARD CURRENT. (A) AVERAGE FORWARD RECTIFIED CURRENT. (A) 8.0 7.0 6.0 5.0 4.0 3.0 2.0 1.0 0 60 Hz RESISTIVE OR INDUCTIVE LOAD 28 24 20 16 FIG.2- MAXIMUM FORWARD CURRENT DERATING CURVE L=0.25" (6.35mm) L=0.125" (3.18mm) 60 Hz RESISTIVE OR INDUCTIVE LOAD GROUND PLANE 1.0 X 1.0" (25.4 X 25.4mm) COPPER SURFACE AREA L=0.375" (9.5mm) BOTH LEADS ATTACHED as HEAT SINKS WITH LENGTH as SHOWN, L 0.050"(1.27mm) min. ALTERNATE P.C.B. 1.1 x 1.0" (30 x 30Mmm) COPPER PADS 20 40 60 80 100 120 o 12 8 4 0 L=0.625" (15.8mm) 0 140 160 180 200 0 20 40 60 80 100 120 o 140 160 180 200 AMBIENT TEMPERATURE. ( C) LEAD TEMPERATURE. ( C) FIG.3- TYPICAL REVERSE CHARACTERISTICS 100 100 FIG.4- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS INSTANTANEOUS REVERSE CURRENT MICROAMPERES INSTANTANEOUS FORDWARD CURRENT AMPERES 10 Tj=125 0C 10 Tj=100 0C 1 1 Tj=25 0C 0.1 0.1 Tj=25 C PULSE WIDTH-300 S 1% DUTY CYCLE 0 0.01 0 20 40 60 80 100 120 140 0.01 0.6 0.8 1.0 1.2 1.4 1.6 1.8 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) INSTANTANEOUS FORWARD VOLTAGE, VOLTS FIG.5- MAXIMUM PEAK FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT AMPERES VRRM may be APPLIED BETWEEN EACH CYCLE of SURGE, the Tj NOTED is Tj PRIOR to SURGE FIG.6- TYPICAL TRANSIENT THERMAL IMPEDANCE TRANSIENT THERMAL IMPEDANCE, OC/W 100 600 10 Tj=25 C 0 100 1 0 0.1 1 NUMBER OF CYCLES AT 60Hz 10 0.1 0.01 0.1 1 T, PULSE DURATION, sec. 10 100 - 527 -