TS78CIC0

TS7800 Series 3-Terminal Fixed Positive Voltage Regulator TO-220 ITO-220 TO-263 2 (D PAK) Pin Definition: 1. Input 2. Ground (tab) 3. Output General Description The TS7800 series voltage regulators are monolithic integrated circuits designed as fixed-voltage regulators for a wide variety of applications including local, on-card regulation. These regulators employ internal current limiting, thermal shutdown, and safe-area compensation. With adequate heatsink they can deliver output currents up to 1 ampere. Although designed primarily as a fixed voltage regulator, these devices can be used with external components to obtain adjustable voltages and currents. Features ● ● ● ● ● ● Output Voltage Range 5 to 24V Output current up to 1A No external components required Internal thermal overload protection Internal short-circuit current limiting Output transistor safe-area compensation Standard Application Circuit ● Output voltage offered in 4% tolerance Ordering Information Part No. TS78xxCZ C0 TS78xxCI C0 TS78xxCM RN A common ground is required between the input and the output voltages. The input voltage must remain typically 2.0V above the output voltage even during the low point on the Input ripple voltage. XX = these two digits of the type number indicate voltage. * = Cin is required if regulator is located an appreciable distance from power supply filter. ** = Co is not needed for stability; however, it does improve transient response. Package TO-220 ITO-220 TO-263 Packing 50pcs / Tube 50pcs / Tube 800pcs / 13” Reel Note: Where xx denote voltage option Absolute Maximum Rating (Ta = 25oC unless otherwise noted) Parameter Input Voltage VOUT=5~18V VOUT=24V Symbol VIN Limit Unit V 35 40 Output Current IOUT Internal Limited Power Dissipation PD Internal Limited Operating Junction Temperature TJ 0~+125 Storage Temperature Range TSTG -65~+150 TO-220 5 Thermal Resistance - Junction to Case ITO-220 RӨJC 5 2 TO-263 (D PAK) 3 TO-220 50 Thermal Resistance - Junction to Ambient ITO-220 RӨJA 60 2 TO-263 (D PAK) 62.5 Note: Absolute maximum ratings are those values beyond which damage to the device may occur. Functional operation under these condition is not implied. 1/12 o o C C o C/W o C/W Version: C11 TS7800 Series 3-Terminal Fixed Positive Voltage Regulator TS7805 Electrical Characteristics (Vin=10V, Iout=500mA, 0 C≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) o o Parameter Output voltage Symbol o Test Condition Tj=25 C 7.5V≤Vin≤20V, 10mA≤Iout≤1A, PD≤15W o 7.5V≤Vin≤25V Tj=25 C 8V≤Vin≤12V o 10mA≤Iout≤1A Tj=25 C 250mA≤Iout≤750mA o Iout=0, Tj=25 C 7.5V≤Vin≤25V 10mA≤Iout≤1A o 10Hz≤f≤100KHz, Tj=25 C f=120Hz, 8V≤Vin≤18V o Iout=1.0A, Tj=25 C f=1KHz o Tj=25 C o Tj=25 C Iout=10mA, 0 C≤Tj≤125 C o o Min 4.80 4.75 --------62 ------ Typ 5 5 3 1 15 5 4.2 --40 78 2 17 750 2.2 -0.6 Max 5.20 5.25 100 50 100 50 8 1.3 0.5 -------- Unit V Vout Line Regulation Load Regulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Ratio Voltage Drop Output Resistance Output Short Circuit Current Peak Output Current Temperature Coefficient of Output Voltage o REGline REGload Iq ∆Iq Vn RR Vdrop Rout Ios Io peak ∆Vout/ ∆Tj mV mA µV dB V mΩ mA A mV/ C o TS7806 Electrical Characteristics (Vin=11V, Iout=500mA, 0 C≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) o Parameter Output Voltage Symbol o Test Condition Tj=25 C 8.5V≤Vin≤21V, 10mA≤Iout≤1A, PD≤15W o 8.5V≤Vin≤25V Tj=25 C 9V≤Vin≤13V o 10mA≤Iout≤1A Tj=25 C 250mA≤Iout≤750mA o Iout=0, Tj=25 C 8.5V≤Vin≤25V 10mA≤Iout≤1A o 10Hz≤f≤100KHz, Tj=25 C f=120Hz, 9V≤Vin≤19V o Iout=1.0A, Tj=25 C f=1KHz o Tj=25 C o Tj=25 C Min 5.75 5.7 --------59 ----- Typ 6 6 5 1.5 14 4 4.3 --45 75 2 19 550 2.2 Max 6.25 6.3 120 60 120 60 8 1.3 0.5 ------- Unit V Vout Line Regulation Load Regulation Quiescent Current Quiescent Current Change REGline REGload Iq ∆Iq mV mA Output Noise Voltage Vn uV Ripple Rejection Ratio RR dB Voltage Drop Vdrop V Output Resistance Rout mΩ Output Short Circuit Current Ios mA Peak Output Current Io peak A Temperature Coefficient of o o o ∆Vout/∆Tj Iout=10mA, 0 C≤Tj≤125 C --0.7 -mV/ C Output Voltage Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. This specification applies only for DC power dissipation permitted by absolute maximum ratings. 2/12 Version: C11 TS7800 Series 3-Terminal Fixed Positive Voltage Regulator TS7808 Electrical Characteristics Vin=14V, Iout=500mA, 0 C≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) o o Parameter Output voltage Symbol o Test Condition Tj=25 C 10.5V≤Vin≤23V, 10mA≤Iout≤1A, PD≤15W 10.5V≤Vin≤25V o Tj=25 C 11V≤Vin≤17V 10mA≤Iout≤1A o Tj=25 C 250mA≤Iout≤750mA o Iout=0, Tj=25 C 10.5V≤Vin≤25V 10mA≤Iout≤1A o 10Hz≤f≤100KHz, Tj=25 C f=120Hz, 11V≤Vin≤21V o Iout=1.0A, Tj=25 C f=1KHz o Tj=25 C o Tj=25 C Iout=10mA, 0 C≤Tj≤125 C o o Min 7.69 7.61 --------56 ------ Typ 8 8 6 2 12 4 4.3 --52 72 2 16 450 2.2 -0.8 Max 8.32 8.40 160 80 160 80 8 1 0.5 -------- Unit V Vout Line Regulation Load Regulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Ratio Voltage Drop Output Resistance Output Short Circuit Current Peak Output Current Temperature Coefficient of Output Voltage o REGline REGload Iq ∆Iq Vn RR Vdrop Rout Ios Io peak ∆Vout/ ∆Tj mV mA µV dB V mΩ mA A mV/ C o TS7809 Electrical Characteristics (Vin=15V, Iout=500mA, 0 C≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) o Parameter Output Voltage Symbol o Test Condition Tj=25 C 11.5V≤Vin≤23V, 10mA≤Iout≤1A, PD≤15W 11.5V≤Vin≤26V o Tj=25 C 12V≤Vin≤17V 10mA≤Iout≤1A o Tj=25 C 250mA≤Iout≤750mA o Iout=0, Tj=25 C 11.5V≤Vin≤26V 10mA≤Iout≤1A o 10Hz≤f≤100KHz, Tj=25 C f=120Hz, 12V≤Vin≤22V o Iout=1.0A, Tj=25 C f=1KHz o Tj=25 C o Tj=25 C Min 8.65 8.57 --------55 ----- Typ 9 9 6 2 12 4 4.3 --52 72 2 16 450 2.2 Max 9.36 9.45 180 90 180 90 8 1 0.5 ------- Unit V Vout Line Regulation Load Regulation Quiescent Current Quiescent Current Change REGline REGload Iq ∆Iq mV mA Output Noise Voltage Vn uV Ripple Rejection Ratio RR dB Voltage Drop Vdrop V Output Resistance Rout mΩ Output Short Circuit Current Ios mA Peak Output Current Io peak A Temperature Coefficient of o o o ∆Vout/ ∆Tj Iout=10mA, 0 C≤Tj≤125 C --1 -mV/ C Output Voltage Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. This specification applies only for DC power dissipation permitted by absolute maximum ratings. 3/12 Version: C11 TS7800 Series 3-Terminal Fixed Positive Voltage Regulator TS7810 Electrical Characteristics Vin=16V, Iout=500mA, 0 C≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) o o Parameter Output voltage Symbol o Test Condition Tj=25 C 12.5V≤Vin≤25V, 10mA≤Iout≤1A, PD≤15W 12.5V≤Vin≤28V o Tj=25 C 13V≤Vin≤17V 10mA≤Iout≤1A o Tj=25 C 250mA≤Iout≤750mA o Iout=0, Tj=25 C 12.5V≤Vin≤28V 10mA≤Iout≤1A o 10Hz≤f≤100KHz, Tj=25 C f=120Hz, 13V≤Vin≤23V o Iout=1.0A, Tj=25 C f=1KHz o Tj=25 C o Tj=25 C Iout=10mA, 0 C≤Tj≤125 C o o Min 9.6 9.5 --------55 ------ Typ 10 10 7 2 12 4 4.3 --70 71 2 18 400 2.2 -1 Max 10.4 10.5 200 100 200 100 8 1 0.5 -------- Unit V Vout Line Regulation Load Regulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Ratio Voltage Drop Output Resistance Output Short Circuit Current Peak Output Current Temperature Coefficient of Output Voltage o REGline REGload Iq ∆Iq Vn RR Vdrop Rout Ios Io peak ∆Vout/ ∆Tj mV mA µV dB V mΩ mA A mV/ C o TS7812 Electrical Characteristics (Vin=19V, Iout=500mA, 0 C≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) o Parameter Output Voltage Symbol o Test Condition Tj=25 C 14.5V≤Vin≤27V, 10mA≤Iout≤1A, PD ≤15W 14.5V≤Vin≤30V o Tj=25 C 15V≤Vin≤19V 10mA≤Iout≤1A o Tj=25 C 250mA≤Iout≤750mA o Tj=25 C, Iout=0 14.5V≤Vin≤30V 10mA≤Iout≤1A o 10Hz≤f≤100KHz, Tj=25 C f=120Hz, 15V≤Vin≤25V o Iout=1.0A, Tj=25 C f=1KHz o Tj=25 C o Tj=25 C Min 11.53 11.42 --------55 ----- Typ 12 12 10 3 12 4 4.3 --75 71 2 18 350 2.2 Max 12.48 12.60 240 120 240 120 8 1 0.5 ------- Unit V Vout Line Regulation Load Regulation Quiescent Current Quiescent Current Change REGline REGload Iq ∆Iq mV mA Output Noise Voltage Vn uV Ripple Rejection Ratio RR dB Voltage Drop Vdrop V Output Resistance Rout mΩ Output Short Circuit Current Ios mA Peak Output Current Io peak A Temperature Coefficient of o o o ∆Vout/ ∆Tj Iout=10mA, 0 C≤Tj≤125 C --1 -mV/ C Output Voltage Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. This specification applies only for DC power dissipation permitted by absolute maximum ratings. 4/12 Version: C11 TS7800 Series 3-Terminal Fixed Positive Voltage Regulator TS7815 Electrical Characteristics Vin=23V, Iout=500mA, 0 C≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) o o Parameter Output voltage Symbol o Test Condition Tj=25 C 17.5V≤Vin≤30V, 10mA≤Iout≤1A, PD ≤15W 17.5V≤Vin≤30V o Tj=25 C 18V≤Vin≤22V 10mA≤Iout≤1A o Tj=25 C 250mA≤Iout≤750mA o Tj=25 C, Iout=0 17.5V≤Vin≤30V 10mA≤Iout≤1A o 10Hz≤f≤100KHz, Tj=25 C f=120Hz, 18V≤Vin≤28V o Iout=1.0A, Tj=25 C f=1KHz o Tj=25 C o Tj=25 C Iout=10mA, 0 C≤Tj≤125 C o o Min 14.42 14.28 --------54 ------ Typ 15 15 12 3 12 4 4.3 --90 70 2 19 230 2.2 -1 Max 15.60 15.75 300 150 300 150 8 1 0.5 -------- Unit V Vout Line Regulation Load Regulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Ratio Voltage Drop Output Resistance Output Short Circuit Current Peak Output Current Temperature Coefficient of Output Voltage o REGline REGload Iq ∆Iq Vn RR Vdrop Rout Ios Io peak ∆Vout/ ∆Tj mV mA µV dB V mΩ mA A mV/ C o TS7818 Electrical Characteristics (Vin=24V, Iout=500mA, 0 C≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) o Parameter Output Voltage Line Regulation Load Regulation Quiescent Current Quiescent Current Change Symbol o Test Condition Tj=25 C 21V≤Vin≤33V, 10mA≤Iout≤1A, PD ≤15W 21V≤Vin≤33V o Tj=25 C 22V≤Vin≤26V 10mA≤Iout≤1A o Tj=25 C 250mA≤Iout≤750mA o Tj=25 C, Iout=0 21V≤Vin≤33V 10mA≤Iout≤1A o 10Hz≤f≤100KHz, Tj=25 C f=120Hz, 21V≤Vin≤31V o Iout=1.0A, Tj=25 C f=1KHz o Tj=25 C o Tj=25 C Min 17.30 17.14 --------54 ----- Typ 18 18 15 5 12 4 4.5 --110 70 2 22 200 2.2 Max 18.72 18.90 360 180 360 180 8 1 0.5 ------- Unit V Vout REGline REGload Iq ∆Iq mV mA Output Noise Voltage Vn uV Ripple Rejection Ratio RR dB Voltage Drop Vdrop V Output Resistance Rout mΩ Output Short Circuit Current Ios mA Peak Output Current Io peak A Temperature Coefficient of o o o ∆Vout/ ∆Tj Iout=10mA, 0 C≤Tj≤125 C --1 -mV/ C Output Voltage Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. This specification applies only for DC power dissipation permitted by absolute maximum ratings. 5/12 Version: C11 TS7800 Series 3-Terminal Fixed Positive Voltage Regulator TS7824 Electrical Characteristics Vin=33V, Iout=500mA, 0 C≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) o o Parameter Output voltage Symbol o Test Condition Tj=25 C 27V≤Vin≤38V, 10mA≤Iout≤1A, PD ≤15W 27V≤Vin≤38V o Tj=25 C 28V≤Vin≤32V 10mA≤Iout≤1A o Tj=25 C 250mA≤Iout≤750mA o Iout=0, Tj=25 C 27V≤Vin≤38V 10mA≤Iout≤1A o 10Hz≤f≤100KHz, Tj=25 C f=120Hz, 27V≤Vin≤37V o Iout=1.0A, Tj=25 C f=1KHz o Tj=25 C o Tj=25 C Min 23.07 22.85 --------54 ----- Typ 24 24 18 6 12 4 4.6 --170 70 2 28 150 2.2 Max 24.96 25.20 480 240 480 240 8 1 0.5 ------- Unit V Vout Line Regulation Load Regulation Quiescent Current Quiescent Current Change REGline REGload Iq ∆Iq mV mA Output Noise Voltage Vn µV Ripple Rejection Ratio RR dB Voltage Drop Vdrop V Output Resistance Rout mΩ Output Short Circuit Current Ios mA Peak Output Current Io peak A Temperature Coefficient of o o o ∆Vout/ ∆Tj Iout=10mA, 0 C≤Tj≤125 C --1.5 -mV/ C Output Voltage Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. This specification applies only for DC power dissipation permitted by absolute maximum ratings. 6/12 Version: C11 TS7800 Series 3-Terminal Fixed Positive Voltage Regulator Electrical Characteristics Curve Figure 1. Peak Output Current as a Function of Input-Output Differential Voltage Figure 2. Ripple Rejection as a Function of Output Voltage Figure 3. Ripple Rejection as a Function of Frequency Figure 4. Output Voltage as a Function of Junction Temperature Figure 5. Output Impedance as a Function of Output Voltage Figure 6. Quiescent Current as a Function of Temperature 7/12 Version: C11 TS7800 Series 3-Terminal Fixed Positive Voltage Regulator Application Information Figure 7. D PAK Thermal Resistance and Maximum Power Dissipation vs. P.C.B Copper Length 2 8/12 Version: C11 TS7800 Series 3-Terminal Fixed Positive Voltage Regulator TO-220 Mechanical Drawing DIM A B C D E F G H I J K L M N O P TO-220 DIMENSION MILLIMETERS INCHES MIN MAX MIN MAX 0.413 9.31 10.50 0.367 0.154 3.74 3.91 0.147 0.128 2.36 3.24 0.093 0.127 2.22 3.22 0.087 0.039 0.78 0.98 0.031 0.104 -2.65 -0.209 -5.30 -0.546 12.32 13.88 0.485 0.365 8.74 9.26 0.344 0.648 15.07 16.47 0.593 0.183 4.35 4.65 0.171 0.055 1.16 1.40 0.046 1.195 28.37 30.35 1.117 0.105 1.78 2.67 0.070 0.024 0.255 0.610 0.010 0.301 5.75 7.65 0.226 Marking Diagram XX Y M = Output Voltage (05=5V, 06=6V, 08=8V, 09=9V, 10=10V, 12=12V, 15=15V, 18=18V, 24=24V) = Year Code = Month Code (A=Jan, B=Feb, C=Mar, D=Apl, E=May, F=Jun, G=Jul, H=Aug, I=Sep, J=Oct, K=Nov, L=Dec) = Lot Code = Package Code for TO-220 L CZ 9/12 Version: C11 TS7800 Series 3-Terminal Fixed Positive Voltage Regulator ITO-220 Mechanical Drawing DIM A B C D E F G H I J K L M N O ITO-220 DIMENSION MILLIMETERS INCHES MIN MAX MIN MAX 9.96 10.36 0.392 0.407 6.20 (typ.) 0.244 (typ.) 2.20 (typ.) 0.087 (typ.) ∮1.40 (typ.) ∮0.055 (typ.) 15.07 16.07 0.593 0.632 0.80 (typ.) 0.031 (typ.) 2.44 2.64 0.096 0.104 13.08 13.48 0.514 0.530 1.47 (max.) 0.057 (max.) 3.20 3.40 0.125 0.133 4.60 4.80 0.181 0.188 1.15 (typ.) 0.045 (typ.) 2.44 2.64 0.096 0.104 2.60 2.80 0.102 0.110 6.55 6.65 0.258 0.262 Marking Diagram XX Y M = Output Voltage (05=5V, 06=6V, 08=8V, 09=9V, 10=10V, 12=12V, 15=15V, 18=18V, 24=24V) = Year Code = Month Code (A=Jan, B=Feb, C=Mar, D=Apl, E=May, F=Jun, G=Jul, H=Aug, I=Sep, J=Oct, K=Nov, L=Dec) = Lot Code = Package Code for ITO-220 L CI 10/12 Version: C11 TS7800 Series 3-Terminal Fixed Positive Voltage Regulator TO-263 Mechanical Drawing DIM A B C D E F G H I J TO-263 DIMENSION MILLIMETERS INCHES MIN MAX MIN MAX 10.000 10.500 0.394 0.413 14.605 15.875 0.575 0.625 0.508 0.991 0.020 0.039 2.420 2.660 0.095 0.105 4.064 4.830 0.160 0.190 1.118 1.400 0.045 0.055 0.450 0.730 0.018 0.029 8.280 8.800 0.325 0.346 1.140 1.400 0.044 0.055 1.480 1.520 0.058 0.060 Marking Diagram = Output Voltage (05=5V, 06=6V, 08=8V, 09=9V, 10=10V, 12=12V, 15=15V, 18=18V, 24=24V) Y = Year Code M = Month Code (A=Jan, B=Feb, C=Mar, D=Apl, E=May, F=Jun, G=Jul, H=Aug, I=Sep, J=Oct, K=Nov, L=Dec) L = Lot Code CM = Package Code for TO-263 XX 11/12 Version: C11 TS7800 Series 3-Terminal Fixed Positive Voltage Regulator Notice Specifications of the products displayed herein are subject to change without notice. TSC or anyone on its behalf, assumes no responsibility or liability for any errors or inaccuracies. Information contained herein is intended to provide a product description only. No license, express or implied, to any intellectual property rights is granted by this document. Except as provided in TSC’s terms and conditions of sale for such products, TSC assumes no liability whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of TSC products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications. Customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify TSC for any damages resulting from such improper use or sale. 12/12 Version: C11