TS78L18CXRF

TS78L00 Series 3-Terminal 100mA Positive Voltage Regulator TO-92 Pin Definition: 1. Output 2. Ground 3. Input SOT-23 Pin Definition: 1. Output 2. Input 3. Ground SOP-8 Pin Definition: 1. Output 8. Input 2. Ground 7. Ground 3. Ground 6. Ground 4. N/C 5. N/C SOT-89 Pin Definition: T S7 8 L 0 0 ACY 1. Output 2. Ground 3. Input T S7 8 L 0 0 CY 1. Input 2. Ground 3. Output General Description The TS78L00 Series of positive voltage Regulators ar e inexpensive, easy-to-use devices suitable for a multitude of applications that require a regulated supply of up to 100mA. Like their higher power TS7800 and TS78M00 Series cousins, these regulators feature internal current limiting and ther mal shutdown making them remarkably rugged. No external components are required with the TS78L00 devices in many applications . These dev ices offer a substantial perfor mance advantage over the traditional zener diode-resis tor combination, as output impedance and quiescent current are substantially reduced. Features ● ● ● ● ● ● ● Output Voltage Range 3.3 to 24V Output current up to 100mA No external components required Inter nal ther mal overload protec tion Inter nal short-circuit current limiting Output trans istor safe-area compensation Output voltage offered in 4% tolerance Standard Application Circuit Ordering Information Part No. Package Packi ng TS78LxxC T B0 TO-92 1Kpcs / Bulk TS78LxxC T A3 TO-92 2Kpcs/ Ammo TS78LxxAC Y R M SOT-89 1Kpcs / 7” Reel TS78LxxC Y RM SOT-89 1Kpcs / 7” Reel TS78LxxC S RL SOP-8 2.5Kpcs / 13” Reel TS78LxxC X RF SOT-23 3Kpcs / 7” Reel Note: W here xx denote voltage option A common g round is required between the input and the output voltages. The input voltage must remain typically 2.0V above the output voltage even during the low point on the Input ripple voltage. XX = these two digits of the type number indicate voltage. * = Cin is required if regula tor is located an appreciable distance from powe r supply filte r. ** = Co is no t needed for stability; however, it does improv e transient response. Absolute Maximum Rating (Ta = 25oC unless otherwise noted) Parameter DC Input Voltage Power Dissipation Operating Junction Temperature Storage Temperature Range TS78L03 TS78L05 ~ TS78L18 TS78L24 PD TJ TSTG Symbol VIN Limit 30 35 40 Inter nal Limited 0 ~ +1 2 5 - 6 5 ~+1 5 0 Unit V W o o C C 1/12 Version: B07 TS78L00 Series 3-Terminal 100mA Positive Voltage Regulator TS78L03 Electrical Characteristics (Vin=8.3V, Iout=40mA, 0 C≤ Tj≤125 C , Cin=0.33uF, C out=0.1uF; unless otherwise specified.) o o Parameter Output voltage Symbol o Test Conditi on Tj=25 C 5.8V≤Vin≤20V, 5mA≤Iout≤100mA Tj=25 C Tj=25 C o o Mi n 3.173 3.142 ------- Ty p 3.3 3.3 50 15 5 3 --40 49 2 0.15 -0.2 Max 3.432 3.465 150 60 30 6 1.5 0.1 ------ Unit V Vout Line R egulation Load R egulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejec tion Ratio Voltage Drop Peak Output Current Temperatur e Coefficient of Output Voltage o REGline REGload Iq ΔIq Vn RR V dr op Io peak ΔVout/ ΔTj 5.8V≤Vin≤20V Iout=40mA 5mA≤Iout≤100mA mV 5mA≤Iout≤40mA o Iout=0, Tj=25 C 5.8V≤Vin≤20V 5mA≤Iout≤40mA 10Hz≤f≤100KHz, Tj=25 C f=120Hz , 5.8V≤ Vin≤20V Iout=100mA, Tj=25 C o Tj=25 C Iout=5mA, 0 C≤Tj≤125 C o o o o mA µV dB V A mV/ C o -41 ---- TS78L05 Electrical Characteristics (Vin=10V, Iout=40mA, 0 C≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) o Parameter Output voltage Symbol o Test Conditi on Tj=25 C 7.5V≤Vin≤20V, 5mA≤Iout≤100mA Tj=25 C Tj=25 C o o Mi n 4.80 4.75 ------- Ty p 5 5 50 20 10 3 --40 49 Max 5.20 5.25 150 60 30 6 1.5 0.1 --- Unit V Vout Line R egulation Load R egulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejec tion Ratio REGline REGload Iq ΔIq Vn RR 7.5V≤Vin≤20V Iout=100mA 5mA≤Iout≤100mA mV 5mA≤Iout≤40mA o Iout=0, Tj=25 C 7.5V≤Vin≤20V 5mA≤Iout≤40mA 10Hz≤f≤100KHz, Tj=25 C f=120Hz , 7.5V≤ Vin≤20V o o mA µV dB -41 Voltage Drop V dr op Iout=100mA, Tj=25 C -1.7 -V o Peak Output Current Io peak Tj=25 C -0.15 -A Temperatur e Coefficient of o o o ΔVout/ ΔTj Iout=5mA, 0 C≤Tj≤125 C --0.65 -mV/ C Output Voltage  Pulse testing techniques are used to maintain the junc tion temperature as close to the ambient temperature as possible, and ther mal effects must be taken into account separately.  This spec ification applies only for DC power dissipation per mitted by absolute max imum ratings. 2/12 Version: B07 TS78L00 Series 3-Terminal 100mA Positive Voltage Regulator TS78L06 Electrical Characteristics Vin=12V, Iout=40mA, 0 C≤Tj≤ 125 C , C in=0.33uF, Cout=0.1uF; unless otherwise specified.) o o Parameter Output voltage Symbol o Test Conditi on Tj=25 C 8.5V≤Vin≤21V, 5mA≤Iout≤100mA 8.5V≤Vin≤21V o Tj=25 C Iout=40mA 5mA≤Iout≤100mA o Tj=25 C 5mA≤Iout≤40mA o Iout=0, Tj=25 C 8.5V≤Vin≤21V 5mA≤Iout≤40mA o 10Hz≤f≤100KHz, Tj=25 C f=120Hz , 8.5V≤ Vin≤21V o Iout=100mA, Tj=25 C Tj=25 C Iout= 5mA, 0 C≤Tj≤125 C o o o Mi n 5.76 5.70 -------41 ---- Ty p 6 6 50 12 4 3 --40 49 1.7 0.15 -0.75 Max 6.24 6.30 150 60 30 6 1.5 0.1 ------ Unit V Vout Line R egulation Load R egulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejec tion Ratio Voltage Drop Peak Output Current Temperatur e Coefficient of Output Voltage o REGline REGload Iq ΔIq Vn RR V dr op Io peak ΔVout/ ΔTj mV mA µV dB V A mV/ C o TS78L08 Electrical Characteristics Vin=14V, Iout=40mA, 0 C≤Tj≤ 125 C , C in=0.33uF, Cout=0.1uF; unless otherwise specified.) o Parameter Output voltage Symbol o Test Conditi on Tj=25 C 10.5V≤ Vin≤23V, 5mA≤Iout≤100mA Tj=25 C Tj=25 C o o Mi n 7.69 7.61 ------- Ty p 8 8 80 25 10 3 --60 57 Max 8.32 8.40 160 80 40 6 1.5 0.1 --- Unit V Vout Line R egulation Load R egulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejec tion Ratio REGline REGload Iq ΔIq Vn RR 10.5V≤ Vin≤23V Iout=40mA 5mA≤Iout≤100mA mV 5mA≤Iout≤40mA o Iout=0, Tj=25 C 10.5V≤ Vin≤23V 5mA≤Iout≤40mA 10Hz≤f≤100KHz, Tj=25 C f=120Hz , 10.5V≤ Vin≤23V o o mA µV dB -37 Voltage Drop V dr op Iout=100mA, Tj=25 C -1.7 -V o Peak Output Current Io peak Tj=25 C -0.15 -A Temperatur e Coefficient of o o o ΔVout/ ΔTj Iout=5mA, 0 C≤Tj≤125 C --0.8 -mV/ C Output Voltage  Pulse testing techniques are used to maintain the junc tion temperature as close to the ambient temperature as possible, and ther mal effects must be taken into account separately.  This spec ification applies only for DC power dissipation per mitted by absolute max imum ratings. 3/12 Version: B07 TS78L00 Series 3-Terminal 100mA Positive Voltage Regulator TS78L09 Electrical Characteristics Vin=15V, Iout=40mA, 0 C≤Tj≤ 125 C , C in=0.33uF, Cout=0.1uF; unless otherwise specified.) o o Parameter Output voltage Symbol o Test Conditi on Tj=25 C 11.5V≤ Vin≤23V, 5mA≤Iout≤100mA 11.5V≤ Vin≤23V o Tj=25 C Iout=40mA Tj=25 C o Mi n 8.65 8.57 -------37 --- Ty p 9 9 90 30 15 3 --60 57 1.7 0.15 -0.9 Max 9.36 9.45 180 90 45 6 1.5 0.1 ------ Unit V Vout Line R egulation Load R egulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejec tion Ratio Voltage Drop Peak Output Current Temperatur e Coefficient of Output Voltage o REGline REGload Iq ΔIq Vn RR V dr op Io peak ΔVout/ ΔTj 5mA≤Iout≤100mA 5mA≤Iout≤40mA o mV Iout=0, Tj=25 C 11.5V≤ Vin≤23V 5mA≤Iout≤40mA o 10Hz≤f≤100KHz, Tj=25 C f=120Hz , 11.5V≤ Vin≤23V o Iout=100mA, Tj=25 C Tj=25 C Iout=5mA, 0 C≤Tj≤125 C o o o mA µV dB V A mV/ C o -- TS78L12 Electrical Characteristics Vin=19V, Iout=40mA, 0 C ≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) o Parameter Output voltage Symbol o Test Conditi on Tj=25 C 14.5V≤ Vin≤27V, 5mA≤Iout≤100mA 14.5V≤ Vin≤27V o Tj=25 C Iout=40mA 5mA≤Iout≤100mA o Tj=25 C 5mA≤Iout≤40mA o Iout=0, Tj=25 C 14.5V≤ Vin≤27V 5mA≤Iout≤40mA o 10Hz≤f≤100KHz, Tj=25 C f=120Hz , 14.5V≤ Vin≤27V o Iout=100mA, Tj=25 C o Mi n 11.53 11.42 -------37 -- Ty p 12 12 120 40 20 3 --80 42 1.7 Max 12.48 12.60 240 120 60 6.5 1.5 0.1 ---- Unit V Vout Line R egulation Load R egulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejec tion Ratio Voltage Drop REGline REGload Iq ΔIq Vn RR V dr op mV mA µV dB V Peak Output Current Io peak Tj=25 C -0.15 -A Temperatur e Coefficient of o o o ΔVout/ ΔTj Iout=5mA, 0 C≤Tj≤125 C --1.0 -mV/ C Output Voltage  Pulse testing techniques are used to maintain the junc tion temperature as close to the ambient temperature as possible, and ther mal effects must be taken into account separately.  This spec ification applies only for DC power dissipation per mitted by absolute max imum ratings. 4/12 Version: B07 TS78L00 Series 3-Terminal 100mA Positive Voltage Regulator TS78L15 Electrical Characteristics Vin=23V, Iout=40mA, 0 C≤Tj≤ 125 C , C in=0.33uF, Cout=0.1uF; unless otherwise specified.) o o Parameter Output voltage Symbol o Test Conditi on Tj=25 C 17.5V≤ Vin≤30V, 5mA≤Iout≤100mA Tj=25 C Tj=25 C o o Mi n 14.42 14.28 ------- Ty p 15 15 150 50 25 3 --90 39 1.7 0.15 -1.3 Max 15.60 15.75 300 150 75 6.6 1.5 0.1 ------ Unit V Vout Line R egulation Load R egulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejec tion Ratio Voltage Drop Peak Output Current Temperatur e Coefficient of Output Voltage o REGline REGload Iq ΔIq Vn RR V dr op Io peak ΔVout/ ΔTj 17.5V≤ Vin≤30V Iout=40mA 5mA≤Iout≤100mA mV 5mA≤Iout≤40mA o Iout=0, Tj=25 C 17.5V≤ Vin≤30V 5mA≤Iout≤40mA 10Hz≤f≤100KHz, Tj=25 C f=120Hz , 17.5V≤ Vin≤30V Iout=100mA, Tj=25 C o Tj=25 C Iout=5mA, 0 C≤Tj≤125 C o o o o mA µV dB V A mV/ C o -34 ---- TS78L18 Electrical Characteristics Vin=27V, Iout=40mA, 0 C≤Tj≤ 125 C , C in=0.33uF, Cout=0.1uF; unless otherwise specified.) o Parameter Output voltage Symbol o Test Conditi on Tj=25 C 21V≤ Vin≤33V, 5mA≤Iout≤100mA Tj=25 C o o Mi n 17.30 17.14 ------- Ty p 18 18 180 60 30 3 --150 48 1.7 0.15 -1.5 Max 18.72 18.90 360 180 90 6.5 1.5 0.1 ------ Unit V Vout Line R egulation Load R egulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejec tion Ratio Voltage Drop Peak Output Current Temperatur e Coefficient of Output Voltage   REGline REGload Iq ΔIq Vn RR V dr op Io peak ΔVout/ ΔTj 21≤Vin≤33V Iout=40mA 5mA≤Iout≤100mA Tj=25 C 5mA≤Iout≤40mA o Iout=0, Tj=25 C 21V≤ Vin≤33V 5mA≤Iout≤40mA 10Hz≤f≤100KHz, Tj=25 C f=120Hz , 21V≤Vin≤33V Iout=100mA, Tj=25 C o Tj=25 C Iout=5mA, 0 C≤Tj≤125 C o o o o mV mA µV dB V A mV/ C o -33 ---- Pulse testing techniques are used to maintain the junc tion temperature as close to the ambient temperature as possible, and ther mal effects must be taken into account separately. This spec ification applies only for DC power dissipation per mitted by absolute max imum ratings. 5/12 Version: B07 TS78L00 Series 3-Terminal 100mA Positive Voltage Regulator TS78L24 Electrical Characteristics Vin=33V, Iout=40mA, 0 C≤Tj≤ 125 C , C in=0.33uF, Cout=0.1uF; unless otherwise specified.) o o Parameter Output voltage Symbol o Test Conditi on Tj=25 C 27V≤ Vin≤38V, 5mA≤Iout≤100mA Tj=25 C Tj=25 C o o Mi n 23.07 22.85 ------- Ty p 24 24 200 80 40 4 --200 45 Max 24.96 25.20 400 240 120 7 1.5 0.1 --- Unit V Vout Line R egulation Load R egulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejec tion Ratio REGline REGload Iq ΔIq Vn RR 27≤Vin≤38V Iout=40mA 5mA≤Iout≤100mA mV 5mA≤Iout≤40mA o Iout=0, Tj=25 C 27V≤ Vin≤38V 5mA≤Iout≤40mA 10Hz≤f≤100KHz, Tj=25 C f=120Hz , 27V≤Vin≤38V o o mA µV dB -31 Voltage Drop V dr op Iout=100mA, Tj=25 C -1.7 -V o Peak Output Current Io peak Tj=25 C -0.15 -A Temperatur e Coefficient of o o o ΔVout/ ΔTj Iout=5mA, 0 C≤Tj≤125 C --2.0 -mV/ C Output Voltage  Pulse testing techniques are used to maintain the junc tion temperature as close to the ambient temperature as possible, and ther mal effects must be taken into account separately.  This spec ification applies only for DC power dissipation per mitted by absolute max imum ratings. 6/12 Version: B07 TS78L00 Series 3-Terminal 100mA Positive Voltage Regulator Application Information Design Considerat ions The TS78L00 Series of fixed voltage regulators are designed with Thermal Overload Protection that shuts down the circuit when subjec ted to an excessive pow er over load condition. Internal Short Circuit protec tion Limits the maximum current the circuit will pass. In many low current applications , compensation capacitors are not required. H owever, it is recommended that the regulator input be bypassed with a capacitor if the r egulator is connected to the power supply filter w ith long wir e lengths, or if the output load capacitance is large. The input bypass capac itor should be selec ted to provide good highfrequency characteris tics to insure s table oper ation under all load conditions. A 0.33uF or larger tantalum, mylar , or other capacitor having low internal impedance at high frequencies should be chosen. The bypass capacitor s hould be mounted with the shortest possible leads direc tly across the regulators input ter minals . Good construc tion techniques should be used to minimize ground loops and lead resistance drops since the regulator has no external sense lead. Bypassing the output is also recommended. FIGURE 7 – Current Regulat or FIGURE 2 – ± 15V Tracking Voltage Regulator The TS78L00 regulators can also be used as a current source when connec ted as above. In order to minimize dissipation the TS78L05 is chosen in this application. Resistor R deter mines the current as follows: FIGURE 8 – ± 15V Tracking Voltage Regulator IIB=3.8mA over lined and load changes For example, a 100mA current source would require R to be a 50Ω . 1/2W resis tor and the output voltage compliance would be the input voltage less 7V. 7/12 Version: B07 TS78L00 Series 3-Terminal 100mA Positive Voltage Regulator TO-92 Mechanical Drawing DIM A B C D E F G H TO-92 DIMEN SION MILLIMETER S INCH ES MIN MAX MIN MAX 4.30 4.70 0.169 0.185 4.30 4.70 0.169 0.185 14.30( typ) 0.563( typ) 0.43 0.49 0.017 0.019 2.19 2.81 0.086 0.111 3.30 3.70 0.130 0.146 2.42 2.66 0.095 0.105 0.37 0.43 0.015 0.017 Marking Diagram XX Y M = Output Voltage (03=3.3V, 05=5V, 06=6V, 08=8V, 09=9V, 12=12V, 15=15V, 18=18V, 24=24V) = Year Code = Month C ode (A=Jan, B =Feb, C=Mar, D=Apl, E=May, F=Jun, G=Jul, H=Aug, I=Sep, J=Oc t, K=Nov , L=Dec) = Lo t C ode L 8/12 Version: B07 TS78L00 Series 3-Terminal 100mA Positive Voltage Regulator SOT-89 Mechanical Drawing DIM A B C D E F G H I J SOT-89 DIMENSION MILLIMETER S INCH ES MIN MAX MIN MAX 4.40 4.60 0.173 0.181 1.50 1.7 0.059 0.070 2.30 2.60 0.090 0.102 0.40 0.52 0.016 0.020 1.50 1.50 0.059 0.059 3.00 3.00 0.118 0.118 0.89 1.20 0.035 0.047 4.05 4.25 0.159 0.167 1.4 1.6 0.055 0.068 0.35 0.44 0.014 0.017 Marking Diagram XX = Output Voltage (03=3.3V, 05=5V, 06=6V, 08=8V, 09=9V, 12=12V, 15=15V, 18=18V, 24=24V) Y = Year Code M = Month C ode (A=Jan, B =Feb, C=Mar, D=Apl, E=May, F=Jun, G=Jul, H=Aug, I=Sep, J=Oc t, K=Nov , L=Dec) L = Lo t C ode XX = Output Voltage (03=3.3V, 05=5V, 06=6V, 08=8V, 09=9V, 12=12V, 15=15V, 18=18V, 24=24V) Y = Year Code M = Month C ode (A=Jan, B =Feb, C=Mar, D=Apl, E=May, F=Jun, G=Jul, H=Aug, I=Sep, J=Oc t, K=Nov , L=Dec) L = Lo t C ode A = TS78LxxAC Y 9/12 Version: B07 TS78L00 Series 3-Terminal 100mA Positive Voltage Regulator SOP-8 Mechanical Drawing DIM A B C D F G K M P R SOP-8 DIMEN SION MILLIMETER S INCH ES MIN MAX MIN MAX. 4.80 5.00 0.189 0.196 3.80 4.00 0.150 0.157 1.35 1.75 0.054 0.068 0.35 0.49 0.014 0.019 0.40 1.25 0.016 0.049 1.27BSC 0.05BSC 0.10 0.25 0.004 0.009 0º 7º 0º 7º 5.80 6.20 0.229 0.244 0.25 0.50 0.010 0.019 Marking Diagram XX Y M = Output Voltage (03=3.3V, 05=5V, 06=6V, 08=8V, 09=9V, 12=12V, 15=15V, 18=18V, 24=24V) = Year Code = Month C ode (A=Jan, B =Feb, C=Mar, D=Apl, E=May, F=Jun, G=Jul, H=Aug, I=Sep, J=Oc t, K=Nov , L=Dec) = Lo t C ode L 10/12 Version: B07 TS78L00 Series 3-Terminal 100mA Positive Voltage Regulator SOT-23 Mechanical Drawing DIM A A1 B C D E F G H I J SOT-23 DIMENSION MILLIMETER S INCH ES MIN MAX MIN MAX. 0.95 BSC 1.9 BSC 2.60 1.40 2.80 1.00 0.00 0.35 0.10 0.30 5º 3.00 1.70 3.10 1.30 0.10 0.50 0.20 0.60 10º 0.037 BSC 0.074 BSC 0.102 0.055 0.110 0.039 0.000 0.014 0.004 0.012 5º 0.118 0.067 0.122 0.051 0.004 0.020 0.008 0.024 10º Marking Diagram L3 = Device Voltage Code (L3=3.3V, L5=5V, L6=6V, L8=8V, L9=9V, L1=10V, L2=12V, A=15V, D=18V, J=24V) Y = Year Code M = Month C ode (A=Jan, B =Feb, C=Mar, D=Apl, E=May, F=Jun, G=Jul, H=Aug, I=Sep, J=Oc t, K=Nov , L=Dec) L = Lo t C ode 11/12 Version: B07 TS78L00 Series 3-Terminal 100mA Positive Voltage Regulator Notice Specifications of the produc ts displayed herein are s ubject to change without notice. TSC or anyone on its behalf, assumes no responsibility or liability for any errors or inaccuracies. Infor mation contained herein is intended to pr ovide a product description only. N o license, express or implied, to any intellectual proper ty rights is granted by this document. Except as provided in TSC’s terms and conditions of sale for such products , TSC assumes no liability whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of TSC products including liability or warranties relating to fitness for a par ticular purpose, merchantability, or infringement of any patent, copyright, or other intellectual proper ty right. The products shown herein are not designed for use in medical, life-saving, or life-sus taining applications . C ustomers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify TSC for any damages resulting from such improper use or sale. 12/12 Version: B07