TS78M00 Series
3-Terminal 500mA Positive Voltage Regulator
TO-220 TO-252 (DPAK)
Pin Definition: 1. Input 2. Ground (tab) 3. Output
General Description
The TS78M00 Series positive voltage regulators are identical to the popular TS7800 Series devices, except that they are specified for only half the output current. Like the TS7800 devices, the TS78M00 Series 3-Terminal regulators are intended for local, on-card voltage regulation. Internal current limiting, thermal shutdown circuitry and safe-area compensation for the internal pass transistor combine to make these devices remarkably rugged under most operating conditions. Maximum output current with adequate heatsink is 500mA
Features
● ● ● ● ● ● ● Output Voltage Range 5 to 24V Output current up to 500mA No external components required Internal thermal overload protection Internal short-circuit current limiting Output transistor safe-area compensation Output voltage offered in 4% tolerance
Standard Application Circuit
Ordering Information
Part No.
TS78MxxCZ C0 TS78MxxCP RO
Package
TO-220 TO-252
Packing
50pcs / Tube 2.5Kpcs / 13” Reel
Note: Where xx denote voltage option
A common ground is required between the input and the output voltages. The input voltage must remain typically 2.0V above the output voltage even during the low point on the Input ripple voltage. XX = these two digits of the type number indicate voltage. * = Cin is required if regulator is located an appreciable distance from power supply filter. ** = Co is not needed for stability; however, it does improve transient response.
Absolute Maximum Rating (Ta = 25oC unless otherwise noted)
Parameter
Input Voltage Input Voltage Power Dissipation Operating Junction Temperature Storage Temperature Range Note: * TS78M05 to TS78M18 ** TS78M24 *** Follow the derating curve
Symbol
VIN* VIN** PD TJ TSTG
Limit
35 40 Internal Limited 0~+125 -65~+150
Unit
V V W
o o
C C
1/10
Version: B07
TS78M00 Series
3-Terminal 500mA Positive Voltage Regulator
TS78M05 Electrical Characteristics
(Vin=10V, Iout=350mA, 0 C≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)
o o
Parameter
Output voltage Line Regulation Load Regulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Ratio Voltage Drop Output Resistance Output Short Circuit Current Peak Output Current Temperature Coefficient of Output Voltage
o
Symbol
o
Test Condition
Tj=25 C 7.5V≤Vin≤20V, 5mA≤Iout≤350mA 7.5V≤Vin≤25V o Tj=25 C 8V≤Vin≤12V 5mA≤Iout≤500mA o Tj=25 C 5mA≤Iout≤200mA o Iout=0, Tj=25 C 7.5V≤Vin≤25V 5mA≤Iout≤350mA o 10Hz≤f≤100KHz, Tj=25 C f=120Hz, 8V≤Vin≤18V o Iout=500mA, Tj=25 C f=1KHz o Tj=25 C o Tj=25 C Iout= 5mA, 0 C≤Tj≤125 C
o o
Min
4.80 4.75 --------62 ------
Typ
5 5 3 1 15 5 3 --40 78 2 17 50 0.7 -0.2
Max
5.20 5.25 100 50 100 50 6 0.8 0.5 --------
Unit
V
Vout REGline REGload Iq ΔIq Vn RR Vdrop Rout Ios Io peak ΔVout/ ΔTj
mV
mA µV dB V mΩ mA A mV/ C
o
TS78M08 Electrical Characteristics
Vin=14V, Iout=350mA, 0 C≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)
o
Parameter
Output voltage Line Regulation Load Regulation Quiescent Current Quiescent Current Change
Symbol
o
Test Condition
Tj=25 C 10.5V≤Vin≤23V, 5mA≤Iout≤350mA 10.5V≤Vin≤25V o Tj=25 C 11V≤Vin≤17V 5mA≤Iout≤500mA o Tj=25 C 5mA≤Iout≤200mA o Iout=0, Tj=25 C 10.5V≤Vin≤25V 5mA≤Iout≤350mA o 10Hz≤f≤100KHz, Tj=25 C f=120Hz, 11V≤Vin≤21V o Iout=500mA, Tj=25 C f=1KHz o Tj=25 C o Tj=25 C
Min
7.69 7.61 --------56 -----
Typ
8 8 6 2 12 4 3 --52 80 2 16 50 0.7
Max
8.32 8.40 160 80 160 80 6 0.8 0.5 -------
Unit
V
Vout REGline REGload Iq ΔIq
mV
mA
Output Noise Voltage Vn µV Ripple Rejection Ratio RR dB Voltage Drop Vdrop V Output Resistance Rout mΩ Output Short Circuit Current Ios mA Peak Output Current Io peak A Temperature Coefficient of o o o ΔVout/ ΔTj Iout= 5mA, 0 C≤Tj≤125 C --0.2 -mV/ C Output Voltage Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. This specification applies only for DC power dissipation permitted by absolute maximum ratings. 2/10 Version: B07
TS78M00 Series
3-Terminal 500mA Positive Voltage Regulator
TS78M09 Electrical Characteristics
(Vin=15V, Iout=350mA, 0 C≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)
o o
Parameter
Output Voltage Line Regulation Load Regulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Ratio Voltage Drop Output Resistance Output Short Circuit Current Peak Output Current Temperature Coefficient of Output Voltage
o
Symbol
o
Test Condition
Tj=25 C 11.5V≤Vin≤23V, 5mA≤Iout≤350mA 11.5V≤Vin≤26V o Tj=25 C 12V≤Vin≤17V 5mA≤Iout≤500mA o Tj=25 C 5mA≤Iout≤200mA o Iout=0, Tj=25 C 11.5V≤Vin≤26V 5mA≤Iout≤350mA o 10Hz≤f≤100KHz, Tj=25 C f=120Hz, 12V≤Vin≤22V o Iout=500mA, Tj=25 C f=1KHz o Tj=25 C o Tj=25 C Iout= 5mA, 0 C≤Tj≤125 C
o o
Min
8.65 8.57 --------55 ------
Typ
9 9 6 2 12 4 3 --52 80 2 16 50 0.7 -0.2
Max
9.36 9.45 180 90 180 90 6 0.8 0.5 --------
Unit
V
Vout REGline REGload Iq ΔIq Vn RR Vdrop Rout Ios Io peak ΔVout/ ΔTj
mV
mA uV dB V mΩ mA A mV/ C
o
TS78M12 Electrical Characteristics
(Vin=19V, Iout=350mA, 0 C≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)
o
Parameter
Output Voltage Line Regulation Load Regulation Quiescent Current Quiescent Current Change
Symbol
o
Test Condition
Tj=25 C 14.5V≤Vin≤27V, 5mA≤Iout≤350mA 14.5V≤Vin≤30V o Tj=25 C 15V≤Vin≤19V 5mA≤Iout≤500mA o Tj=25 C 5mA≤Iout≤200mA o Tj=25 C, Iout=0 14.5V≤Vin≤30V 5mA≤Iout≤500mA o 10Hz≤f≤100KHz, Tj=25 C f=120Hz, 15V≤Vin≤25V o Iout=500mA, Tj=25 C f=1KHz o Tj=25 C o Tj=25 C
Min
11.53 11.42 --------55 -----
Typ
12 12 10 3 12 4 3 --75 80 2 18 50 0.7
Max
12.48 12.60 240 120 240 120 6 0.8 0.5 -------
Unit
V
Vout REGline REGload Iq ΔIq
mV
mA
Output Noise Voltage Vn uV Ripple Rejection Ratio RR dB Voltage Drop Vdrop V Output Resistance Rout mΩ Output Short Circuit Current Ios mA Peak Output Current Io peak A Temperature Coefficient of o o o ΔVout/ ΔTj Iout=5mA, 0 C≤Tj≤125 C --0.3 -mV/ C Output Voltage Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. This specification applies only for DC power dissipation permitted by absolute maximum ratings.
3/10
Version: B07
TS78M00 Series
3-Terminal 500mA Positive Voltage Regulator
TS78M15 Electrical Characteristics
(Vin=23V, Iout=350mA, 0 C≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)
o o
Parameter
Output voltage Line Regulation Load Regulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Ratio Voltage Drop Output Resistance Output Short Circuit Current Peak Output Current Temperature Coefficient of Output Voltage
o
Symbol
Vout REGline REGload Iq ΔIq Vn RR Vdrop Rout Ios Io peak ΔVout/ ΔTj
Test Condition
Tj=25 C 17.5V≤Vin≤30V, 5mA≤Iout≤350mA 17.5V≤Vin≤30V o Tj=25 C 18V≤Vin≤22V 5mA≤Iout≤500mA o Tj=25 C 5mA≤Iout≤200mA o Tj=25 C, Iout=0 17.5V≤Vin≤30V 5mA≤Iout≤500mA o 10Hz≤f≤100KHz, Tj=25 C f=120Hz, 18V≤Vin≤28V o Iout=500mA, Tj=25 C f=1KHz o Tj=25 C o Tj=25 C Iout=10mA, 0 C≤Tj≤125 C
o o o
Min
14.42 14.28 --------54 ------
Typ
15 15 12 3 12 4 3 --90 80 2 19 50 0.7 -0.3
Max
15.60 15.75 300 150 300 150 6 0.8 0.5 --------
Unit
V
mV
mA µV dB V mΩ mA A mV/ C
o
TS78M18 Electrical Characteristics
(Vin=24V, Iout=350mA, 0 C≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)
o
Parameter
Output Voltage Line Regulation Load Regulation Quiescent Current Quiescent Current Change
Symbol
o
Test Condition
Tj=25 C 21V≤Vin≤33V, 5mA≤Iout≤350mA 21V≤Vin≤33V o Tj=25 C 22V≤Vin≤26V 5mA≤Iout≤500mA o Tj=25 C 5mA≤Iout≤200mA o Tj=25 C, Iout=0 21V≤Vin≤33V 5mA≤Iout≤500mA o 10Hz≤f≤100KHz, Tj=25 C f=120Hz, 21V≤Vin≤31V o Iout=500mA, Tj=25 C f=1KHz o Tj=25 C o Tj=25 C
Min
17.30 17.14 --------54 -----
Typ
18 18 15 5 12 4 3 --110 80 2 22 50 0.7
Max
18.72 18.90 360 180 360 180 6 0.8 0.5 -------
Unit
V
Vout REGline REGload Iq ΔIq
mV
mA
Output Noise Voltage Vn uV Ripple Rejection Ratio RR dB Voltage Drop Vdrop V Output Resistance Rout mΩ Output Short Circuit Current Ios mA Peak Output Current Io peak A Temperature Coefficient of o o o ΔVout/ ΔTj Iout= 5mA, 0 C≤Tj≤125 C --0.5 -mV/ C Output Voltage Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. This specification applies only for DC power dissipation permitted by absolute maximum ratings.
4/10
Version: B07
TS78M00 Series
3-Terminal 500mA Positive Voltage Regulator
TS78M24 Electrical Characteristics
Vin=33V, Iout=350mA, 0 C≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)
o o
Parameter
Output voltage Line Regulation Load Regulation Quiescent Current Quiescent Current Change
Symbol
o
Test Condition
Tj=25 C 27V≤Vin≤38V, 5mA≤Iout≤350mA 27V≤Vin≤38V o Tj=25 C 28V≤Vin≤32V 5mA≤Iout≤500mA o Tj=25 C 5mA≤Iout≤200mA o Iout=0, Tj=25 C 27V≤Vin≤38V 5mA≤Iout≤500mA o 10Hz≤f≤100KHz, Tj=25 C f=120Hz, 27V≤Vin≤37V o Iout=500mA, Tj=25 C f=1KHz o Tj=25 C o Tj=25 C
Min
23.07 22.85 --------54 -----
Typ
24 24 18 6 12 4 3 --170 80 2 28 50 0.7
Max
24.96 25.20 480 240 480 240 6 0.8 0.5 -------
Unit
V
Vout REGline REGload Iq ΔIq
mV
mA
Output Noise Voltage Vn µV Ripple Rejection Ratio RR dB Voltage Drop Vdrop V Output Resistance Rout mΩ Output Short Circuit Current Ios mA Peak Output Current Io peak A Temperature Coefficient of o o o ΔVout/ ΔTj Iout= 5mA, 0 C≤Tj≤125 C --0.5 -mV/ C Output Voltage Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. This specification applies only for DC power dissipation permitted by absolute maximum ratings.
5/10
Version: B07
TS78M00 Series
3-Terminal 500mA Positive Voltage Regulator
Electrical Characteristics Curve
Figure 1. Worst Case Power Dissipation vs. Ambient Temperature (TO-220)
Figure 2. Peak Output Current vs. Dropout Voltage
Figure 3. Bias Current vs. Input Voltage
Figure 4. Dropout Voltage vs. Junction Temperature
Figure 5. Bias Current vs. Output Current
Figure 6. Ripple Rejection vs. Frequency
6/10
Version: B07
TS78M00 Series
3-Terminal 500mA Positive Voltage Regulator
Application information
Figure 7. DPAK Thermal Resistance and Maximum Power Dissipation vs. P.C.B Copper Length
7/10
Version: B07
TS78M00 Series
3-Terminal 500mA Positive Voltage Regulator
TO-220 Mechanical Drawing
DIM A B C D E F G H I J K L M N O P
TO-220 DIMENSION MILLIMETERS INCHES MIN MAX MIN MAX 10.000 10.500 0.394 0.413
3.740 3.910 0.147 0.154
2.440 0.381 2.345 4.690 12.700 8.382 14.224 3.556 0.508 27.700 2.032 0.255 5.842
2.940 6.350 1.106 2.715 5.430 14.732 9.017 16.510 4.826 1.397 29.620 2.921 0.610 6.858
0.096 0.015 0.092 0.092 0.500 0.330 0.560 0.140 0.020 1.060 0.080 0.010 0.230
0.116 0.250 0.040 0.058 0.107 0.581 0.355 0.650 0.190 0.055 1.230 0.115 0.024 0.270
Marking Diagram
XX Y M = Output Voltage (05=5V, 08=8V, 09=9V, 12=12V, 15=15V, 18=18V, 24=24V) = Year Code = Month Code (A=Jan, B=Feb, C=Mar, D=Apl, E=May, F=Jun, G=Jul, H=Aug, I=Sep, J=Oct, K=Nov, L=Dec) = Lot Code = Package Code for TO-220
L CZ
8/10
Version: B07
TS78M00 Series
3-Terminal 500mA Positive Voltage Regulator
TO-252 Mechanical Drawing
TO-252 DIMENSION DIM A A1 B C D E F G G1 G2 H I J K L M MILLIMETERS MIN MAX 2.3BSC 4.6BSC 6.80 5.40 6.40 2.20 0.00 5.20 0.75 0.55 0.35 0.90 2.20 0.50 0.90 1.30 7.20 5.60 6.65 2.40 0.20 5.40 0.85 0.65 0.65 1.50 2.80 1.10 1.50 1.70 INCHES MIN MAX 0.09BSC 0.18BSC 0.268 0.213 0.252 0.087 0.000 0.205 0.030 0.022 0.014 0.035 0.087 0.020 0.035 0.051 0.283 0.220 0.262 0.094 0.008 0.213 0.033 0.026 0.026 0.059 0.110 0.043 0.059 0.67
Marking Diagram
XX Y M = Output Voltage (05=5V, 08=8V, 09=9V, 12=12V, 15=15V, 18=18V, 24=24V) = Year Code = Month Code (A=Jan, B=Feb, C=Mar, D=Apl, E=May, F=Jun, G=Jul, H=Aug, I=Sep, J=Oct, K=Nov, L=Dec) = Lot Code = Package Code for TO-252
L CP
9/10
Version: B07
TS78M00 Series
3-Terminal 500mA Positive Voltage Regulator
Notice
Specifications of the products displayed herein are subject to change without notice. TSC or anyone on its behalf, assumes no responsibility or liability for any errors or inaccuracies. Information contained herein is intended to provide a product description only. No license, express or implied, to any intellectual property rights is granted by this document. Except as provided in TSC’s terms and conditions of sale for such products, TSC assumes no liability whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of TSC products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications. Customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify TSC for any damages resulting from such improper use or sale.
10/10
Version: B07