TS7900A series
3-Terminal Fixed Negative Output Voltage Regulator
TO-263
Pin assignment: 1. Ground 2. Input 3. Output (Heatsink surface connected to Pin 2)
Voltage Range - 5V to - 24V Output Current up to 1.5A
General Description
The TS7900A series of fixed output negative voltage regulators are intended as complements to the popular TS7800A series device. These negative regulators are available in the same seven-voltage options as the TS7800A devices. Available in fixed output voltage options from -5.0 to -24 volts, these regulators employ current limiting, thermal shutdown, and safe-area compensation--making them remarkably rugged under most operating conditions. With adequate heat sink they can deliver output currents in excess of 1.5 ampere. This series is offered in 3-pin TO-220, TO-263 package.
Features
Output current up to 1.5A No external components required Internal thermal overload protection Internal short-circuit current limiting Output transistor safe-area compensation Output voltage offered in +/-2% tolerance
Standard Application
Ordering Information
Part No.
TS79xxACZ TS79xxACM
Operating Temp. (Ambient)
o -20 ~ +85 C
Package
TO-220 TO-263
Note: Where xx denotes voltage option.
A common ground is required between the input and the output voltages. The input voltage must remain typically 2.0V above the output voltage even during the low point on the Input ripple voltage. XX = these two digits of the type number indicate voltage. * = Cin is required if regulator is located an appreciable distance from power supply filter. ** = Co is not needed for stability; however, it does improve transient response.
Absolute Maximum Rating
Input Voltage Input Voltage Power Dissipation TO-220 TO-220 TO-263 Operating Junction Temperature Range Storage Temperature Range Note : * TS7905A to TS7918A ** TS7924A *** Follow the derating curve Vin * Vin ** Without heatsink Pt *** Without heatsink TJ TSTG - 35 - 40 2 15 1.5 0 ~ +150 -65 ~ +150
o o
V V
W
C C
TS7900A series
1-1
2003/12 rev. A
TS7905A Electrical Characteristics
(Vin= -10V, Iout=500mA, 0 oC ≤Tj≤125 oC, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)
Parameter
Output voltage
Symbol
o
Test Conditions
Tj=25 C -7.5V≤Vin≤ -20V, 10mA≤Iout≤1A, PD≤15W -7.5V≤Vin≤-25V -8V≤Vin≤-12V 10mA≤Iout≤1.5A 250mA≤Iout≤750mA
o
Min
-4.90 -4.80
Typ
-5 -5
Max
-5.10 -5.20
Unit
V
Vout
Line Regulation
REGline
Tj=25 oC
o
--------
3 1 15 5 4 --40 74 2 2.1 -1
100 50 100 50 8 1.3 0.5 -----uV dB V A mV/
o
mV
Load Regulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Ratio Voltage Drop Peak Output Current Temperature Coefficient of Output Voltage
REGload Iq ∆lq Vn RR Vdrop Io peak ∆Vout/∆Tj
Tj=25 C
Iout=0, Tj=25 C -7.5V≤Vin≤-25V 10mA≤Iout≤1A 10Hz≤f≤100KHz, Tj=25 C f=120Hz, -8V≤Vin≤-18V Iout=1.0A, Tj=25 C Tj=25 C
o o Iout=10mA, 0 C ≤Tj≤125 C o o o
mA
-62 ----
C
TS7908A Electrical Characteristics
(Vin=-14V, Iout=500mA, 0 oC ≤Tj≤125 oC, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)
Parameter
Output Voltage
Symbol
o
Test Conditions
Tj=25 C -10.5V≤Vin≤-23V, 10mA≤Iout≤1A, PD≤15W -10.5V≤Vin≤-25V -11V≤Vin≤-17V 10mA≤Iout≤1.5A 250mA≤Iout≤750mA
o
Min
-7.84 -7.68
Typ
-8 -8
Max
-8.16 -8.32
Unit
V
Vout
Line Regulation
REGline
Tj=25 oC Tj=25 oC
--------
6 2 12 4 4 --52 72 2 2.1 -1
160 80 160 80 8 1 0.5 -----uV dB V A mV/
o
mV
Load Regulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Ratio Voltage Drop Peak Output Current Temperature Coefficient of Output Voltage
REGload Iq ∆lq Vn RR Vdrop Io peak ∆Vout/∆Tj
Iout=0, Tj=25 C -10.5V≤Vin≤-25V 10mA≤Iout≤1A 10Hz≤f≤100KHz, Tj=25 C f=120Hz, -11V≤Vin≤-21V Iout=1.0A, Tj=25 C Tj=25 C
o o Iout=10mA, 0 C ≤Tj≤125 C o o o
mA
-56 ----
C
Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. This specification applies only for DC power dissipation permitted by absolute maximum ratings.
TS7900A series
2-2
2003/12 rev. A
TS7909A Electrical Characteristics
(Vin=-15V, Iout=500mA, 0 oC ≤Tj≤125 oC, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)
Parameter
Output Voltage
Symbol
o
Test Conditions
Tj=25 C -11.5V≤Vin≤-23V, 10mA≤Iout≤1A, PD≤15W -11.5V≤Vin≤-26V -12V≤Vin≤-17V 10mA≤Iout≤1.5A 250mA≤Iout≤750mA
o
Min
-8.88 -8.64
Typ
-9 -9
Max
-9.18 -9.36
Unit
V
Vout
Line Regulation
REGline
Tj=25 oC Tj=25 oC
--------
6 2 12 4 4 --58 71 2 2.1 -1
180 90 180 90 8 1 0.5 -----uV dB V A mV/
o
mV
Load Regulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Ratio Voltage Drop Peak Output Current Temperature Coefficient of Output Voltage
REGload Iq ∆lq Vn RR Vdrop Io peak ∆Vout/∆Tj
Iout=0, Tj=25 C -11.5V≤Vin≤-26V 10mA≤Iout≤1A 10Hz≤f≤100KHz, Tj=25 C f=120Hz, -12V≤Vin≤-22V Iout=1.0A, Tj=25 C Tj=25 C
o o Iout=10mA, 0 C ≤Tj≤125 C o o o
mA
-56 ----
C
TS7912A Electrical Characteristics
(Vin=-19V, Iout=500mA, 0 oC ≤Tj≤125 oC, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)
Parameter
Output Voltage
Symbol
o
Test Conditions
Tj=25 C -14.5V≤Vin≤-27V, 10mA≤Iout≤1A, PD ≤15W -14.5V≤Vin≤-30V -15V≤Vin≤-19V 10mA≤Iout≤1.5A 250mA≤Iout≤750mA
Min
-11.76 -11.52
Typ
-12 -12
Max
-12.24 -12.48
Unit
V
Vout
Line Regulation
REGline
Tj=25 oC Tj=25 oC
o
--------
10 3 12 4 4 --75 70 2 2.1 -1
240 120 240 120 8 1 0.5 -----uV dB V A mV/
o
mV
Load Regulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Ratio Voltage Drop Peak Output Current Temperature Coefficient of Output Voltage
REGload Iq ∆lq Vn RR Vdrop Io peak ∆Vout/∆Tj
Tj=25 C, Iout=0 -14.5V≤Vin≤-30V 10mA≤Iout≤1A 10Hz≤f≤100KHz, Tj=25 C f=120Hz, 15V≤Vin≤25V Iout=1.0A, Tj=25 C Tj=25 C
o o Iout=10mA, 0 C ≤Tj≤125 C o o o
mA
-55 ----
C
Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. This specification applies only for DC power dissipation permitted by absolute maximum ratings.
TS7900A series
3-3
2003/12 rev. A
TS7915A Electrical Characteristics
(Vin=-23V, Iout=500mA, 0 oC ≤Tj≤125 oC, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)
Parameter
Output Voltage
Symbol
o
Test Conditions
Tj=25 C -17.5V≤Vin≤-30V, 10mA≤Iout≤1A, PD ≤15W -17.5V≤Vin≤-30V -18V≤Vin≤-22V 10mA≤Iout≤1.5A 250mA≤Iout≤750mA
Min
-14.70 -14.40
Typ
-15 -15
Max
-15.30 -15.60
Unit
V
Vout
Line Regulation
REGline
Tj=25 oC Tj=25 oC
o
--------
12 3 12 4 4 --90 69 2 2.1 -1
300 150 300 150 8 1 0.5 -----uV dB V A mV/
o
mV
Load Regulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Ratio Voltage Drop Peak Output Current Temperature Coefficient of Output Voltage
REGload Iq ∆lq Vn RR Vdrop Io peak ∆Vout/∆Tj
Tj=25 C, Iout=0 -17.5V≤Vin≤-30V 10mA≤Iout≤1A 10Hz≤f≤100KHz, Tj=25 C f=120Hz, -18V≤Vin≤-28V Iout=1.0A, Tj=25 C Tj=25 C
o o Iout=10mA, 0 C ≤Tj≤125 C o o o
mA
-54 ----
C
TS79818A Electrical Characteristics
(Vin=-27V, Iout=500mA, 0 oC ≤Tj≤125 oC, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)
Parameter
Output Voltage
Symbol
o
Test Conditions
Tj=25 C -21V≤Vin≤-33V, 10mA≤Iout≤1A, PD ≤15W -21V≤Vin≤-33V -22V≤Vin≤-26V 10mA≤Iout≤1.5A 250mA≤Iout≤750mA
Min
-17.64 -17.28
Typ
-18 -18
Max
-18.36 -18.72
Unit
V
Vout
Line Regulation
REGline
Tj=25 oC Tj=25 oC
o
--------
15 5 12 4 4 --110 68 2 2.1 -1
360 180 360 180 8 1 0.5 -----uV dB V A mV/
o
mV
Load Regulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Ratio Voltage Drop Peak Output Current Temperature Coefficient of Output Voltage
REGload Iq ∆lq Vn RR Vdrop Io peak ∆Vout/∆Tj
Tj=25 C, Iout=0 -21V≤Vin≤-33V 10mA≤Iout≤1A 10Hz≤f≤100KHz, Tj=25 C f=120Hz, -21V≤Vin≤-31V Iout=1.0A, Tj=25 C Tj=25 C
o o Iout=10mA, 0 C ≤Tj≤125 C o o o
mA
-53 ----
C
Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. This specification applies only for DC power dissipation permitted by absolute maximum ratings.
TS7900A series
4-4
2003/12 rev. A
TS7824A Electrical Characteristics
(Vin=-33V, Iout=500mA, 0 oC ≤Tj≤125 oC, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)
Parameter
Output Voltage
Symbol
o
Test Conditions
Tj=25 C -27V≤Vin≤-38V, 10mA≤Iout≤1A, PD ≤15W -27V≤Vin≤-38V -28V≤Vin≤-32V 10mA≤Iout≤1.5A 250mA≤Iout≤750mA
o
Min
-23.52 -23.04
Typ
-24 -24
Max
-24.48 -24.96
Unit
V
Vout
Line Regulation
REGline
Tj=25 oC Tj=25 oC
--------
18 6 12 4 4 --170 65 2 2.1 -1
480 240 480 240 8 1 0.5 -----uV dB V A mV/
o
mV
Load Regulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Ratio Voltage Drop Peak Output Current Temperature Coefficient of Output Voltage
REGload Iq ∆lq Vn RR Vdrop Io peak ∆Vout/∆Tj
Iout=0, Tj=25 C -27V≤Vin≤-38V 10mA≤Iout≤1A 10Hz≤f≤100KHz, Tj=25 C f=120Hz, -27V≤Vin≤-37V Iout=1.0A, Tj=25 C Tj=25 C
o o Iout=10mA, 0 C ≤Tj≤125 C o o o
mA
-50 ----
C
Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. This specification applies only for DC power dissipation permitted by absolute maximum ratings.
TS7900A series
5-5
2003/12 rev. A
Electrical Characteristics Curve
FIGURE 1 - Worst Case Power Dissipation v.s. Ambient Temperature FIGURE 2 - Peak Output Current v.s. Input-Output Differential Voltage
FIGURE 3 –Ripple Rejection v.s. Frequency
FIGURE 4 –Ripple Rejection v.s. Output Voltage
FIGURE 5 –Output Voltage v.s. Junction Temperature
FIGURE 6 –Quiescent Current v.s. Temperature
TS7900A series
6-6
2003/12 rev. A
TO-220 Mechanical Drawing
A
B
C
K L
DIM
TO-220 DIMENSION MILLIMETERS INCHES MIN 10.000 3.240 2.440 0.381 2.345 4.690 12.700 8.382 14.224 3.556 0.508 27.700 2.032 0.255 5.842 MAX 10.500 4.440 2.940 6.350 1.106 2.715 5.430 14.732 9.017 16.510 4.826 1.397 29.620 2.921 0.610 6.858 MIN 0.394 0.128 0.096 0.015 0.092 0.092 0.500 0.330 0.560 0.140 0.020 1.060 0.080 0.010 0.230 MAX 0.413 0.175 0.116 0.250 0.040 0.058 0.107 0.581 0.355 0.650 0.190 0.055 1.230 0.115 0.024 0.270
P
J I
M
D H F G E
O N
A B C D E F G H I J K L M N O P
TO-263 Mechanical Drawing
A
E F
DIM A B C D E F G H I J
B
I H
C D
G
TO-263 DIMENSION MILLIMETERS INCHES MIN MAX MIN MAX 10.000 10.500 0.394 0.413 14.605 15.875 0.575 0.625 0.508 0.991 0.020 0.039 2.420 2.660 0.095 0.105 4.064 4.830 0.160 0.190 1.118 1.400 0.045 0.055 0.450 0.730 0.018 0.029 8.280 8.800 0.325 0.346 1.140 1.400 0.044 0.055 1.480 1.520 0.058 0.060
TS7900A series
7-7
2003/12 rev. A