TS79M18ACZC0

TS79M00A Series 3-Terminal 500mA Negative Voltage Regulator TO-220 TO-252 (DPAK) Pin Definition: 1. Input 2. Ground (tab) 3. Output General Description The TS79M00A series of fixed output negative voltage regulators are intended as complements to the popular TS78M00A series device. These negative regulators ar e available in the same seven-voltage options as the TS7900A devices. In addition, one ex tra voltage option commonly employed in MECL systems is also available in the negative TS79M00A Series. Available in fixed output voltage options from -5.0 to -24 volts, these regulators employ current limiting, thermal shutdow n, and safe-area compensation-- making them remarkably rugged under most operating conditions. With adequate heat sinking they can deliver output currents in excess of 0.5 ampere. This series is offered in 3-pin TO-220 & TO-252 package. Features ● ● ● ● ● ● Output Voltage Range -5 to -24V Output current up to 0.5A No external components required Inter nal ther mal overload protec tion Inter nal short-circuit current limiting Output trans istor safe-area compensation Standard Application Circuit ● Output voltage offered in 2% tolerance Ordering Information Part No. TS79MxxACZ C0 TS79MxxACP RO A common g round is required between the input and the output voltages. The input voltage must remain typically 2.0V above the output voltage even during the low point on the Input ripple voltage. XX = these two digits of the type number indicate voltage. * = Cin is required if regula tor is located an appreciable distance from powe r supply filte r. ** = Co is no t needed for stability; however, it does improv e transient response. Package TO-220 TO-252 Packi ng 50pc s / T ube 2.5Kpcs / 13” Reel Note: W here xx denote voltage option Absolute Maximum Rating (Ta = 25oC unless otherwise noted) Parameter Input Voltage Input Voltage Power Dissipation Operating Junction Temperature Storage Temperature Range Note: * TS79M05A to TS79M18A ** TS79M24A *** Follow the derating curve 1/10 Symbol VIN* VIN** PD TJ TSTG Limit - 35 - 40 Inter nal Limited 0 ~+1 2 5 - 6 5 ~+1 5 0 Unit V V W o o C C Version: A07 TS79M00A Series 3-Terminal 500mA Negative Voltage Regulator TS79M05A Electrical Characteristics (Vin= -10V, Iout=350mA, 0 C≤ Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) o o Parameter Output voltage Line R egulation Load R egulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejec tion Ratio Voltage Drop Peak Output Current Temperatur e Coefficient of Output Voltage o Symbol o Test Conditi on Tj=25 C -7.5V≤Vin≤-20V, 5mA≤Iout≤500mA, PD≤5W -7.5V≤Vin≤-25V o Tj=25 C -8V≤Vin≤-18V 5mA≤Iout≤500mA o Tj=25 C 250mA≤Iout≤200mA o Iout=0, Tj=25 C -7.5V≤Vin≤-25V 5mA≤Iout≤500mA o 10Hz≤f≤100KHz, Tj=25 C f=120Hz , - 8V≤ Vin≤-18V o Iout=500mA, Tj=25 C o Tj=25 C Iout=5mA, 0 C≤Tj≤125 C o o Mi n -4.90 -4.85 --------54 ---- Ty p -5 -5 7 2 20 10 4 --40 66 2 0.7 -0.1 Max -5.10 -5.15 50 30 100 50 8 1 0.5 ------ Unit V Vout REGline REGload Iq ΔIq Vn RR V dr op Io peak ΔVout/ ΔTj mV mA µV dB V A mV/ C o TS79M06A Electrical Characteristics (Vin= -11V, Iout=350mA, 0 C≤ Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) o Parameter Output Voltage Line R egulation Load R egulation Quiescent Current Quiescent Current Change Symbol o Test Conditi on Tj=25 C -8.5V≤Vin≤-21V, 5mA≤Iout≤500mA, PD≤5W -8.5V≤Vin≤-25V o Tj=25 C -9V≤Vin≤-13V 5mA≤Iout≤500mA o Tj=25 C 250mA≤Iout≤200mA o Iout=0, Tj=25 C -8.5V≤Vin≤-25V 5mA≤Iout≤500mA o 10Hz≤f≤100KHz, Tj=25 C f=120Hz , - 9V≤ Vin≤-19V o Iout=500mA, Tj=25 C o Tj=25 C Mi n -5.88 -5.76 --------60 --- Ty p -6 -6 5 1.5 14 4 4 --44 73 2 0.7 Max -6.12 -6.24 120 60 120 60 8 1 0.5 ----- Unit V Vout REGline REGload Iq ΔIq mV mA Output Noise Voltage Vn uV Ripple Rejec tion Ratio RR dB Voltage Drop V dr op V Peak Output Current Io peak A Temperatur e Coefficient of o o o ΔVout/ ΔTj Iout=5mA, 0 C≤Tj≤125 C --0.1 -mV/ C Output Voltage  Pulse testing techniques are used to maintain the junc tion temperature as close to the ambient temperature as possible, and ther mal effects must be taken into account separately.  This spec ification applies only for DC power dissipation per mitted by absolute max imum ratings. 2/10 Version: A07 TS79M00A Series 3-Terminal 500mA Negative Voltage Regulator TS79M08A Electrical Characteristics Vin= -14V, Iout=350mA, 0 C≤Tj≤125 C, Cin=0.33uF, C out=0.1uF; unless otherwise specified.) o o Parameter Output voltage Line R egulation Load R egulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejec tion Ratio Voltage Drop Peak Output Current Temperatur e Coefficient of Output Voltage o Symbol o Test Conditi on Tj=25 C -10.5V≤Vin≤-23V, 5mA≤Iout≤500mA, PD≤5W -10.5V≤Vin≤-25V o Tj=25 C -11V≤ Vin≤-17V 5mA≤Iout≤500mA o Tj=25 C 250mA≤Iout≤200mA o Iout=0, Tj=25 C 10.5V≤ Vin≤25V 5mA≤Iout≤500mA o 10Hz≤f≤100KHz, Tj=25 C f=120Hz , 11V≤Vin≤21V o Iout=500mA, Tj=25 C o Tj=25 C Iout=5mA, 0 C≤Tj≤125 C o o Mi n -7.84 -7.68 --------56 ---- Ty p -8 -8 6 2 12 4 4.3 --52 72 2 0.7 -1 Max -8.16 -8.32 160 80 160 80 8 1 0.5 ------ Unit V Vout REGline REGload Iq ΔIq Vn RR V dr op Io peak ΔVout/ ΔTj mV mA µV dB V A mV/ C o TS79M09A Electrical Characteristics (Vin= -15V, Iout=350mA, 0 C≤ Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) o Parameter Output Voltage Line R egulation Load R egulation Quiescent Current Quiescent Current Change Symbol o Test Conditi on Tj=25 C -11.5V≤Vin≤-23V, 5mA≤Iout≤500mA, PD≤5W -11.5V≤Vin≤-26V o Tj=25 C -12V≤ Vin≤-17V 5mA≤Iout≤500mA o Tj=25 C 250mA≤Iout≤200mA o Iout=0, Tj=25 C -11.5V≤Vin≤-26V 5mA≤Iout≤500mA o 10Hz≤f≤100KHz, Tj=25 C f=120Hz , - 12V≤ Vin≤-22V o Iout=500mA, Tj=25 C o Tj=25 C Mi n -8.82 -8.64 --------56 --- Ty p -9 -9 6 2 12 4 4.3 --58 71 2 0.7 Max -9.18 -9.36 180 90 180 90 8 1 0.5 ----- Unit V Vout REGline REGload Iq ΔIq mV mA Output Noise Voltage Vn uV Ripple Rejec tion Ratio RR dB Voltage Drop V dr op V Peak Output Current Io peak A Temperatur e Coefficient of o o o ΔVout/ ΔTj Iout=5mA, 0 C≤Tj≤125 C --1 -mV/ C Output Voltage  Pulse testing techniques are used to maintain the junc tion temperature as close to the ambient temperature as possible, and ther mal effects must be taken into account separately.  This spec ification applies only for DC power dissipation per mitted by absolute max imum ratings. 3/10 Version: A07 TS79M00A Series 3-Terminal 500mA Negative Voltage Regulator TS79M12A Electrical Characteristics (Vin= -19V, Iout=350mA, 0 C≤ Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) o o Parameter Output voltage Line R egulation Load R egulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejec tion Ratio Voltage Drop Peak Output Current Temperatur e Coefficient of Output Voltage o Symbol o Test Conditi on Tj=25 C -14.5V≤Vin≤-27V, 5mA≤Iout≤500mA, PD ≤5W -14.5V≤Vin≤-30V o Tj=25 C -15V≤ Vin≤-19V 5mA≤Iout≤500mA o Tj=25 C 250mA≤Iout≤200mA o Tj=25 C , Iout=0 -14.5V≤Vin≤-30V 5mA≤Iout≤500mA o 10Hz≤f≤100KHz, Tj=25 C f=120Hz , - 15V≤ Vin≤-25V o Iout=500mA, Tj=25 C o Tj=25 C Iout=5mA, 0 C≤Tj≤125 C o o Mi n -11.76 -11.52 --------55 ---- Ty p - 12 - 12 10 3 12 4 4.3 --75 70 2 2.1 -1 Max -12.24 -12.48 240 120 240 120 8 1 0.5 ------ Unit V Vout REGline REGload Iq ΔIq Vn RR V dr op Io peak ΔVout/ ΔTj mV mA µV dB V A mV/ C o TS79M15A Electrical Characteristics Vin= -23V, Iout=350mA, 0 C≤Tj≤125 C, Cin=0.33uF, C out=0.1uF; unless otherwise specified.) o Parameter Output Voltage Line R egulation Load R egulation Quiescent Current Quiescent Current Change Symbol o Test Conditi on Tj=25 C -17.5V≤Vin≤-30V, 5mA≤Iout≤500mA, PD ≤5W -17.5V≤Vin≤-30V o Tj=25 C -18V≤ Vin≤-22V 5mA≤Iout≤500mA o Tj=25 C 250mA≤Iout≤200mA o Tj=25 C , Iout=0 -17.5V≤Vin≤-30V 5mA≤Iout≤500mA o 10Hz≤f≤100KHz, Tj=25 C f=120Hz , - 18V≤ Vin≤-28V o Iout=500mA, Tj=25 C o Tj=25 C Mi n -14.70 -14.40 --------54 --- Ty p - 15 - 15 12 3 12 4 4.3 --90 69 2 0.7 Max -15.30 -15.60 300 150 300 150 8 1 0.5 ----- Unit V Vout REGline REGload Iq ΔIq mV mA Output Noise Voltage Vn uV Ripple Rejec tion Ratio RR dB Voltage Drop V dr op V Peak Output Current Io peak A Temperatur e Coefficient of o o o ΔVout/ ΔTj Iout=5mA, 0 C≤Tj≤125 C --1 -mV/ C Output Voltage  Pulse testing techniques are used to maintain the junc tion temperature as close to the ambient temperature as possible, and ther mal effects must be taken into account separately.  This spec ification applies only for DC power dissipation per mitted by absolute max imum ratings. 4/10 Version: A07 TS79M00A Series 3-Terminal 500mA Negative Voltage Regulator TS79M18A Electrical Characteristics (Vin= -24V, Iout=350mA, 0 C≤ Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) o o Parameter Output voltage Line R egulation Load R egulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejec tion Ratio Voltage Drop Peak Output Current Temperatur e Coefficient of Output Voltage o Symbol o Test Conditi on Tj=25 C -21V≤ Vin≤-33V, 5mA≤Iout≤500mA, PD ≤5W -21V≤ Vin≤-33V o Tj=25 C -22V≤ Vin≤-26V 5mA≤Iout≤500mA o Tj=25 C 250mA≤Iout≤200mA o Iout=0, Tj=25 C -21V≤ Vin≤-33V 5mA≤Iout≤500mA o 10Hz≤f≤100KHz, Tj=25 C f=120Hz , - 21V≤ Vin≤-31V o Iout=500mA, Tj=25 C o Tj=25 C Iout=5mA, 0 C≤Tj≤125 C o o Mi n -17.64 -17.28 --------53 ---- Ty p - 18 - 18 15 5 12 4 4.5 --110 68 2 0.7 -1 Max -18.36 -18.72 360 180 360 180 8 1 0.5 ------ Unit V Vout REGline REGload Iq ΔIq Vn RR V dr op Io peak ΔVout/ ΔTj mV mA µV dB V A mV/ C o TS79M24A Electrical Characteristics Vin= -33V, Iout=350mA, 0 C≤Tj≤125 C, Cin=0.33uF, C out=0.1uF; unless otherwise specified.) o Parameter Output Voltage Line R egulation Load R egulation Quiescent Current Quiescent Current Change Symbol o Test Conditi on Tj=25 C -27V≤ Vin≤-38V, 5mA≤Iout≤500mA, PD ≤5W -27V≤ Vin≤-38V o Tj=25 C -28V≤ Vin≤-32V 5mA≤Iout≤500mA o Tj=25 C 250mA≤Iout≤200mA o Iout=0, Tj=25 C -27V≤ Vin≤-38V 5mA≤Iout≤500mA o 10Hz≤f≤100KHz, Tj=25 C f=120Hz , - 27V≤ Vin≤-37V o Iout=500mA, Tj=25 C o Tj=25 C Mi n -23.52 -23.07 --------50 --- Ty p - 24 - 24 18 6 12 4 4.6 --170 65 2 0.7 Max -24.48 -25.96 480 240 480 240 8 1 0.5 ----- Unit V Vout REGline REGload Iq ΔIq mV mA Output Noise Voltage Vn uV Ripple Rejec tion Ratio RR dB Voltage Drop V dr op V Peak Output Current Io peak A Temperatur e Coefficient of o o o ΔVout/ ΔTj Iout=5mA, 0 C≤Tj≤125 C --1 -mV/ C Output Voltage  Pulse testing techniques are used to maintain the junc tion temperature as close to the ambient temperature as possible, and ther mal effects must be taken into account separately.  This spec ification applies only for DC power dissipation per mitted by absolute max imum ratings. . 5/10 Version: A07 TS79M00A Series 3-Terminal 500mA Negative Voltage Regulator Electrical Characteristics Curve Fi gure 1. Worse Case Power Dissi pati on vs. Ambient Temperatur e (TO-220) Fi gure 2. Peak Output Curr ent as a Functi on of Input-Output Differential Voltage Fi gure 3. Bias Current vs. I nput Voltage Fi gure 4. Bias Current vs. Output Current Fi gure 5. Ri pple Rejecti on vs. Frequency Fi gure 6. Ri pple Rejecti on vs. Output Voltage 6/10 Version: A07 TS79M00A Series 3-Terminal 500mA Negative Voltage Regulator Application information Figure 7. D PAK Thermal Resistance and Maximum Power Dissipat ion vs. P.C .B C opper Lengt h 7/10 Version: A07 TS79M00A Series 3-Terminal 500mA Negative Voltage Regulator TO-220 Mechanical Drawing DIM A B C D E F G H I J K L M N O P TO-220 DIMEN SION MILLIMETER S INCH ES MIN MAX MIN MAX 10.000 10.500 0.394 0.413 3.740 3.910 0.147 0.154 2.440 0.381 2.345 4.690 12.700 8.382 14.224 3.556 0.508 27.700 2.032 0.255 5.842 2.940 6.350 1.106 2.715 5.430 14.732 9.017 16.510 4.826 1.397 29.620 2.921 0.610 6.858 0.096 0.015 0.092 0.092 0.500 0.330 0.560 0.140 0.020 1.060 0.080 0.010 0.230 0.116 0.250 0.040 0.058 0.107 0.581 0.355 0.650 0.190 0.055 1.230 0.115 0.024 0.270 Marking Diagram XX Y M = Output Voltage (05=-5V, 06=-6V, 08=-8V, 09=-9V, 12=-12V, 15=-15V, 18=-18V, 24=-24V) = Year Code = Month C ode (A=Jan, B =Feb, C=Mar, D=Apl, E=May, F=Jun, G=Jul, H=Aug, I=Sep, J=Oc t, K=Nov , L=Dec) = Lo t C ode = Package Code for TO-220 L CZ 8/10 Version: A07 TS79M00A Series 3-Terminal 500mA Negative Voltage Regulator TO-252 Mechanical Drawing TO-252 DIMEN SION MILLIMETER S INCH ES MIN MAX MIN MAX 2.3BSC 0.09BSC 4.6BSC 0.18BSC 6.80 7.20 0.268 0.283 5.40 5.60 0.213 0.220 6.40 6.65 0.252 0.262 2.20 2.40 0.087 0.094 0.00 0.20 0.000 0.008 5.20 5.40 0.205 0.213 0.75 0.85 0.030 0.033 0.55 0.65 0.022 0.026 0.35 0.65 0.014 0.026 0.90 1.50 0.035 0.059 2.20 2.80 0.087 0.110 0.50 1.10 0.020 0.043 0.90 1.50 0.035 0.059 1.30 1.70 0.051 0.67 DIM A A1 B C D E F G G1 G2 H I J K L M Marking Diagram XX Y M = Output Voltage (05=-5V, 06=-6V, 08=-8V, 09=-9V, 12=-12V, 15=-15V, 18=-18V, 24=-24V) = Year Code = Month C ode (A=Jan, B =Feb, C=Mar, D=Apl, E=May, F=Jun, G=Jul, H=Aug, I=Sep, J=Oc t, K=Nov , L=Dec) = Lo t C ode = Package Code for TO-252 L CP 9/10 Version: A07 TS79M00A Series 3-Terminal 500mA Negative Voltage Regulator Notice Specifications of the produc ts displayed herein are s ubject to change without notice. TSC or anyone on its behalf, assumes no responsibility or liability for any errors or inaccuracies. Infor mation contained herein is intended to pr ovide a product description only. N o license, express or implied, to any intellectual proper ty rights is granted by this document. Except as provided in TSC’s terms and conditions of sale for such products , TSC assumes no liability whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of TSC products including liability or warranties relating to fitness for a par ticular purpose, merchantability, or infringement of any patent, copyright, or other intellectual proper ty right. The products shown herein are not designed for use in medical, life-saving, or life-sus taining applications . C ustomers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify TSC for any damages resulting from such improper use or sale. 10/10 Version: A07