TS9010ACX5

TS9010 150mA CMOS Low Dropout Voltage Regulator with Enable Pin assignment 1. Ground 2. Input 3. Enable 4. N/C 5. Output Low Power Consumption Low Drop Out Voltage 0.4V Enable Shutdown General Description The TS9010 series is combine high accuracy with very low power consumption, providing high output current even when the application requires very low dropout voltage. The Chip Enable (CE) includes a CMOS or TTL compatible input allows the output to be turned off to prolong battery life. The TS9010 series is included a precision voltage reference, error correction circuit, a current limited output driver and over temperature shutdown. This series are offered in 5-pin SOT-25 package. Features Dropout voltage typically 0.4V @Io=150mA (Vo=5V) Output current up to 150mA (Vout=3V) Low power consumption Output voltage +/-2% Internal current limit Thermal shutdown protection Ordering Information Part No. Operating Temp. (Ambient) Package Applications Palmtops Video recorders Battery powered equipment PC peripherals High-efficiency linear power supplies Digital signal camera TS9010xCX5 -40 ~ +85 oC SOT-25 Note: Where x denotes voltage option, available are A= 1.5V D= 1.8V, K= 2.5V, S= 3.3V, 5= 5.0V. Contact factory for additional voltage options. Typical Application Circuit Block Diagram CE (pin 3) may be connected directly to Vin (pin 2) TS9010 series 1-4 2004/09 rev. C Absolute Maximum Rating (Note 1) Description Input Supply Voltage Enable Input Voltage Output Current Power Dissipation (Note 3) Thermal Resistance Operating Junction Temperature Range Storage Temperature Range Lead Soldering Temperature (260 oC) Symbol Vin Vce Io PD Өja Tj TSTG Value +12 0 ~ Vin+0.3 200 380 220 -40 ~ +125 -65 ~ +150 5 Unit V V mA mW o C/W o o C C S Recommend Operating Rating (Note 2) Input Supply Voltage Enable Input Voltage Vin Vce +10 Gnd-0.3 ~ Vin+0.3 V V Electrical Characteristics Ta = 25 oC, Cout=2.2uF, Vce2V, unless otherwise specified. Parameter Output Voltage Output Voltage Temperature Coefficient (Note 4) Line Regulation Load Regulation (Note 5) Conditions Vin=Vo + 1V, Io= 40mA Min 0.98|Vo| -- Typ Max 1.02|Vo| Unit V ppm/ oC %/V 100 0.2 30 -0.3 80 Vo+1V ≤ Vin ≤ Vo+2V, Io=1mA Vin=Vo+1V, 1mA≤IL≤150mA Vin=Vo+1V, 1mA≤IL≤80mA Vo ≥ 2.5V --- mV Vo< 2.5V ---------40 200 400 0.01 --300 45 0.05 90 400 700 1 19 0.1 ---- Dropout Voltage (Note 6) Io=80mA Io=150mA Vin≤0.4V (shutdown) Vin=Ven=Vo+1V Vin=Vo+1V, Ven=Gnd Vout=0V At f=100Hz, Io=0.1mA, mV uA uA mA dB %/W Quiescent Current Ground Pin Current (Note 7) Output Current Limit Power Supply Rejection Ratio Thermal Regulation (Note 8) Enable Input Enable Input Logic-Low Voltage Enable Input Logic-High Voltage Enable Input Current Regulation shutdown Regulation enable Vce=Vin Vce=Gnd -1.5 -0.2 ---0.05 0.25 -1 0 V V uA TS9010 series 2-4 2004/09 rev. C Electrical Characteristics (continued) Note 1: Exceeding the absolute maximum rating may damage the device. Note 2: The device is not guaranteed to function outside its operating rating. Note 3: The maximum allowable power dissipation at any Ta is Pd(max) = [ Tj(max) - Ta] * Өja. Exceeding the maximum allowable power dissipation will result in excessive die temperature, and the regulator will go into thermal shutdown. Note 4: Output voltage temperature coefficient is defined as the worst case voltage change divided by the total temperature range. Note 5: Regulation is measured at constant junction temperature using low duty cycle pulse testing. Parts are tested for load regulation in the load range from 1mA to 150mA(Vout>2.5V) and 1mA to 80mA(Vout