AS0606J0560T5E

DATA SHEET Product Name Anti-Surge Thick Film Chip Resistors Part Name AS Series Uniroyal Electronics Global Co., Ltd. 88#, Longteng Road, Economic & Technical Development Zone, Kunshan, Jiangsu, China Tel Email Manufacture Plant +86 512 5763 1411 / 22 /33 marketing@uni-royal.cn Uniroyal Electronics Industry Co., Ltd. Aeon Technology Corporation Royal Electronic Factory (Thailand) Co., Ltd. Royal Technology (Thailand) Co., Ltd. Anti-Surge Thick Film Chip Resistors 1. Scope 1.1 This datasheet is the characteristics of Anti-Surge Thick Film Chip Resistors manufactured by UNI-ROYAL. 1.2 Superior Anti-surge Voltage performance 1.3 Suitable for both wave& re-flow soldering 1.4 Application AV adapters，LCD back-light camera strobe etc. 2. Part No. System Part No. includes 14 codes shown as below: 2.1 1st~4th codes: Part name. E.g.: AS02,AS05,AS06,AS07,AS10,AS12. 2.2 5th~6th codes: Power rating. E.g.: W=Normal Size “1~G” = “1~16” Wattage 1/32 3/4 1/2 1/3 1/4 1/8 1/10 1/16 1/20 1 Normal Size WH 07 W2 W3 W4 W8 WA WG WM 1W If power rating is equal or lower than 1 watt, 5th code would be “W” and 6th code would be a number or letter. E.g.: WA=1/10W W4=1/4W 2.3 7th code: Tolerance. E.g.: D=±0.5% F=±1% G=±2% J=±5% K= ±10% 2.4 8th~11th codes: Resistance Value. 2.4.1 If value belongs to standard value of E-24 series, the 8th code is zero, 9th~10th codes are the significant figures of resistance value, and the 11th code is the power of ten. 2.4.2 If value belongs to standard value of E-96 series, the 8th~10th codes are the significant figures of resistance value, and the 11th code is the power of ten. 2.4.311th codes listed as following: 0=100 1=101 2=102 3=103 4=104 5=105 6=106 J=10-1 K=10-2 L=10-3 M=10-4 th th 2.5 12 ~14 codes. 2.5.1 12th code: Packaging Type. E.g.: C=Bulk T=Tape/Reel 2.5.2 13th code: Standard Packing Quantity. 4=4,000pcs 5=5,000pcs C=10,000pcs D=20,000pcs E=15,000pcs Chip Product: BD=B/B-20000pcs TC=T/R-10000pcs 2.5.3 14th code: Special features. E = Environmental Protection, Lead Free, or Standard type. 3. Ordering Procedure (Example: AS06 0.6W ±5% 10KΩ T/R-5000) A S 0 6 Product Type: Fill-in 4 digits with the chip resistor type as follows: AS02 AS03 AS05 AS06 AS07 AS10 AS12 0 Wattage: W4=1/4W W2=1/2W 06=0.6W 07=3/4W 1A=1.5W 2W=2W 6 J 0 1 0 3 T Resistance Value: 5%,10%,20% (E-24 series): 1st code is zero, 2nd~3rd codes are the significant figures of resistance value, and the rest code is the power of ten. 1% (E-96 series): 1st~3rd codes are the significant figures of resistance value and the rest code is the power of ten. J=10-1; K=10-2; L=10-3 5 E Packing quantity: 1=1000PCS 2=2000PCS 3=3000PCS 4=4000PCS 5=5000PCS C=10000PCS Special Feature E= Lead-Free Tolerance: J=±5%K=±10% M=±20% Apr.29,2020 V.5 www. uni-royal.cn Packing Type: T=Tape/Reel Page 2/8 Anti-Surge Thick Film Chip Resistors 4. Marking 4.1 For AS02 size. Due to the very small size of the resistor’s body, there is no marking on the body. 4.2 ±5%±10% ±20% tolerance products (E-24 series): 3 codes. 1st~2nd codes are the significant figures of resistance value, and the rest code is the power of ten. 333  33K 4.3 5%±10% ±20%Tolerance: below 10 Show as following, read alphabet”R” as decimal point. 2R2  2.2 5. Dimension Dimension(mm) Type AS02(0402) L 1.00±0.10 W H 0.50±0.05 0.35±0.05 A 0.20±0.10 B 0.25±0.10 AS03(0603) 1.60±0.10 0.80±0.10 0.45±0.10 0.30±0.20 0.30±0.20 AS05(0805) 2.00±0.15 1.25 +0.15/-0.10 0.55±0.10 0.40±0.20 0.40±0.20 AS06(1206) 3.10±0.15 1.55 +0.15/ -0.10 0.55±0.10 0.45±0.20 0.45±0.20 AS07(1210) 3.10±0.10 2.60±0.20 0.55±0.10 0.50±0.25 0.50±0.20 AS10(2010) 5.00±0.10 2.50±0.20 0.55±0.10 0.60±0.25 0.50±0.20 3.20±0.20 0.55±0.10 0.60±0.25 0.50±0.20 AS12(2512) 6.35±0.10 6. Resistance Range Type AS02 AS03 AS05 AS06 AS07 AS10 AS12 Power Rating at 70℃ 1/8W 1/4W 1/2W 0.6W 3/4W 1.5W 2W 5% 1Ω~10MΩ 1Ω~10MΩ 1Ω~10MΩ 1Ω~10MΩ 1Ω~10MΩ 1Ω~10MΩ 1Ω~10MΩ Resistance Range 10% 1Ω~10MΩ 1Ω~10MΩ 1Ω~10MΩ 1Ω~10MΩ 1Ω~10MΩ 1Ω~10MΩ 1Ω~10MΩ 20% 1Ω~10MΩ 1Ω~10MΩ 1Ω~10MΩ 1Ω~10MΩ 1Ω~10MΩ 1Ω~10MΩ 1Ω~10MΩ 7. Ratings Type Max. Working Voltage AS02 AS03 AS05 AS06 AS07 AS10 AS12 50V 75V 150V 200V 200V 400V 500V Apr.29,2020 V.5 Max. Overload Voltage 100V 150V 300V 400V 500V 800V 1000V www. uni-royal.cn Dielectric withstanding Voltage Operating Temperature -300V 500V 500V 500V 500V 500V -55℃~155℃ -55℃~155℃ -55℃~155℃ -55℃~155℃ -55℃~155℃ -55℃~155℃ -55℃~155℃ Page 3/8 Anti-Surge Thick Film Chip Resistors 8. Soldering pad size recommended Type AS03 AS05 AS06 AS07 AS10 AS12 A 0.8±0.05 1.0±0.1 2.0±0.1 2.0±0.1 3.6±0.1 4.9±0.1 Dimension(mm) B C 0.65±0.05 0.8±0.05 1.0±0.1 1.4±0.1 1.1±0.1 1.8±0.1 1.1±0.1 3.0±0.1 1.4±0.1 3.0±0.1 1.35±0.1 3.7±0.1 D 2.4±0.05 3.0±0.1 4.2±0.1 4.2±0.1 6.4±0.1 7.6±0.1 9. Derating Curve Power rating will change based on continuous load at ambient temperature from -55 to 155℃. It is constant between -55 to 70℃, and derate to zero when temperature rise from 70 to 155℃. Voltage rating: Resistors shall have a rated direct-current (DC) continuous working voltage or an approximate sine-wave root-mean-square (RMS) alternating-current (AC) continuous working voltage at commercial-line frequency and waveform corresponding to the power rating, as determined from the following formula: RCWV √ R Remark: RCWV: Rating Continuous Working Voltage (Volt.) P: power rating (Watt) R: nominal resistance (Ω) In no case, the rated DC or RMS AC continuous working voltage must be greater than the applicable maximum value. The overload voltage is 2.5 times RCWV or Max. Overload voltage whichever is lower. 10. One-pulse Limiting Electric Power Curve of Pulse Duration ： Pulse Voltage Limit ： Apr.29,2020 V.5 www. uni-royal.cn Page 4/8 Anti-Surge Thick Film Chip Resistors 11. Structure 12. Performance Specification Characteristic Temperature Coefficient Test Methods (GB/T5729&JIS-C-5201&IEC60115-1) Limits 1Ω≦R≤10Ω:±400PPM/℃ 10Ω＜R≤10M: ±100PPM/℃ 4.8 Natural resistance changes per temp. Degree centigrade R2-R1 × 106 (PPM/℃) R1(t2-t1) R1: Resistance Value at room temperature （t1）; R2: Resistance at test temperature (Upper limit temperature or Lower limit temperature) t1: +25°C or specified room temperature t2: Upper limit temperature or Lower limit temperature test temperature Short-time overload ±(1.0%+0.1Ω) 4.13 Permanent resistance change after the application of 2.5 times RCWV for 5 seconds. Terminal bending ±(1.0%+0.05Ω) 4.33 Twist of test board: Y/X = 3/90 mm for 60Seconds Solderability Coverage must be over 95%. 4.17 The area covered with a new, smooth, clean, shiny and continuous surface free from concentrated pinholes. Temperature of solder:245±3°C; Dwell time in solder: 2~3 seconds. Dielectric withstanding voltage No evidence of flashover mechanical damage, arcing or insulation breakdown. 4.7 Clamped in the trough of a 90℃ metallic V-block and shall be tested at ac potential respectively specified in the type for 60-70 seconds Soldering heat ±(1.0%+0.05Ω) 4.18 Dipping the resistor into a solder bath having a temperature of 260℃5℃ and hold it for 10±1 seconds Rapid change of temperature ±(1.0%+0.05) 4.19 30 min at lower limit temperature and 30 min at upper limit temperature，100 cycles. Load life in humidity ±(3.0%+0.1) 7.9 Resistance change after 1,000 hours (1.5 hours “ON”,0.5 hour “OFF”) at RCWV in a humidity chamber controlled at 40℃±2℃ and 90 to 95% relative humidity. Load life ±(3.0%+0.1) 4.25.1 Permanent resistance change after 1,000 hours operating at RCWV with duty cycle 1.5 hours “ON”, 0.5 hour “OFF” at 70℃±2℃ ambient. Humidity ( steady state ) ±(3.0%+0.1) 4.24Temporary resistance change after 240 hours exposure in a humidity test chamber controlled at 40±2℃ and 90-95% relative humidity, ±(3.0%+0.1) 4.23.4 Lower limit temperature，for 2H. ±(3.0%+0.1) 4.23.2 Upper limit temperature ，for 1000H. Low Temperature Storage High Temperature Apr.29,2020 V.5 www. uni-royal.cn Page 5/8 Anti-Surge Thick Film Chip Resistors Exposure Leaching No visible damage J-STD-002 Test D Samples completely immersed for 30 sec in solder bath at 260℃ 13. Soldering Condition (This is for recommendation, please customer perform adjustment according to actual application) 13.1 Recommend Reflow Soldering Profile：(solder : Sn96.5 / Ag3 / Cu0.5) Profile Feature Lead (Pb)-Free solder Preheat： Temperature Min (Tsmin) 150℃ Temperature Max (Tsmax) 200℃ Time (Tsmin to Tsmax ) (ts) 60 -120 seconds Average ramp-up rate： (Ts max to Tp) 3℃ / second max. Time maintained above : Temperature (TL) 217℃ Time (tL) 60-150 seconds Peak Temperature (Tp) 260℃ Time within 0 ℃ of actual peak Temperature (tp)2 5 10 seconds Ramp-own Rate 6℃/second max. Time 25℃ to Peak Temperature 8mimutes max. Allowed Re-flow times : 2 times Remark : To avoid discoloration phenomena of chip on terminal electrodes, please use N2 Re-flow furnace . 13.2 Recommend Wave Soldering Profile：(Apply to 0603 and above size) Apr.29,2020 V.5 www. uni-royal.cn Page 6/8 Anti-Surge Thick Film Chip Resistors 13. Packing 13.1 Dimension of Paper Taping :(Unit: mm) Type A ±0.10 B ±0.10 C ±0.05 AS02 0.65 1.20 2.00 TYPE A  0.2 B  0.2 C  0.05 AS03 1.10 1.90 AS05 1.65 2.40 AS06 2.00 AS07 2.80 . ΦD 1.50 E ±0.1 F ±0.05 G ±0.1 W ±0.2 T ±0.05 1.75 3.50 4.00 8.00 0.42 . E  0.1 F  0.05 G  0.1 W  0.2 T ±0.10 2.00 1.50 1.75 3.50 4.00 8.00 0.67 2.00 1.50 1.75 3.50 4.00 8.00 0.81 3.60 2.00 1.50 1.75 3.50 4.00 8.00 0.81 3.50 2.00 1.50 1.75 3.50 4.00 8.00 0.75 ΦD 13.2 Dimension of plastic taping：(Unit: mm) Type A 0.2 B 0.2 C 0.05 AS10 2.90 5.60 2.00 AS12 3.50 6.70 2.00 ΦD . 1.50 1.50 E 0.1 F 0.05 G 0.1 W 0.2 T ±0.1 1.50 1.75 5.50 4.00 12.00 1.00 1.50 1.75 5.50 4.00 12.00 1.00 C0.5 21.0 21.0 21.0 21.0 21.0 21.0 21.0 D1 60.0 60.0 60.0 60.0 60.0 60.0 60.0 ΦD1 . 13.3 Dimension of Reel：(Unit: mm) Type AS02 AS03 AS05 AS06 AS07 AS10 AS12 Taping Paper Embossed Size 10,000pcs 5000pcs 4000pcs A0.5 2.0 2.0 2.0 2.0 2.0 2.0 2.0 B0.5 13.0 13.0 13.0 13.0 13.0 13.0 13.0 M2 178.0 178.0 178.0 178.0 178.0 178.0 178.0 W1 10.0 10.0 10.0 10.0 10.0 13.8 13.8 14. Note 14.1. UNI-ROYAL recommend products store in warehouse with temperature between 15 to 35℃ under humidity between 25 to 75%RH. Apr.29,2020 V.5 www. uni-royal.cn Page 7/8 Anti-Surge Thick Film Chip Resistors Even under storage conditions recommended above, solder ability of products will be degraded stored over 1 year old. 14.2. Cartons must be placed in correct direction which indicated on carton, otherwise the reel or wire will be deformed. 14.3. Storage conditions as below are inappropriate: a. Stored in high electrostatic environment b. Stored in direct sunshine, rain, snow or condensation. c. Exposed to sea wind or corrosive gases, such as Cl2, H2S, NH3, SO2, NO2, etc. 15. Record Version Description Page Date Amended by Checked by 1 First version 1~7 Mar.20, 2018 Haiyan Chen Nana Chen 2 Modify characteristic 5~6 Feb.13, 2019 Haiyan Chen Yuhua Xu 7 July.29, 2019 Haiyan Chen Yuhua Xu 7 July.29, 2019 Haiyan Chen Yuhua Xu 6~7 Apr.29, 2020 Haiyan Chen Yuhua Xu 3 4 5 Modify the High Temperature Exposure conditions Modify the High Temperature Exposure conditions Modify the reflow curve and add the wave soldering curve © Uniroyal Electronics Global Co., Ltd. All rights reserved. Specification herein will be changed at any time without prior notice. Apr.29,2020 V.5 www. uni-royal.cn Page 8/8