FR1601

FR1601 THRU FR1606 16.0 AMP FAST RECOVERY RECTIFIERS VOLTAGE RANGE 50 to 800 Volts CURRENT FEATURES * Low forward voltage drop * High current capability * High reliability * High surge current capability .412 (10.5) MAX. 16.0 Amperes TO-220 3.8 f +.2 HOLE THRU .180 (4.6) .050 (1.27) .108 (2.75) .248 (6.3) MECHANICAL DATA * Case: Molded plastic * Epoxy: UL 94V-0 rate flame retardant * Lead: Lead solderable per MIL-STD-202, method 208 guranteed * Polarity: As Marked * Mounting position: Any * Weight: 2.24 grams .051 MAX. (1.3) .040 MAX. (1.0) .100 (2.54) PIN 1 PIN 3 Positive CT Suffix "C" .595 (15.1) MAX. .550 (14.0) .158 (4.0) MIN. MAX. .120 (3.05) + CASE PIN 2 PIN 1 PIN 3 Negative CT Suffix "A" CASE PIN 2 Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating 25 C ambient temperature uniess otherwies specified. Single phase half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. TYPE NUMBER Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current .375"(9.5mm) Lead Length at Tc=100 C Peak Forward Surge Current, 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Maximum Instantaneous Forward Voltage at 8.0A Maximum DC Reverse Current Tc=25 C at Rated DC Blocking Voltage Tc=100 C Maximum Reverse Recovery Time (Note 1) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range TJ, TSTG NOTES: FR1601 50 35 50 FR1602 FR1603 FR1604 100 70 100 200 140 200 16.0 200 1.3 10.0 200 150 -65 65 +150 400 280 400 FR1605 600 420 600 FR1606 UNITS 800 560 800 V V V A A V A 250 500 A nS pF C 1. Reverse Recovery Time test condition: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1MHz and applied reverse voltage of 4.0V D.C. RATING AND CHARACTERISTIC CURVES (FR1601 THRU FR1606) FIG.1-TYPICAL FORWARD CHARACTERISTICS AVERAGE FORWARD CURRENT,(A) 24 20 16 12 8 4 0 0 Tj=25 C Pulse Width 300us 1% Duty Cycle Single Phase Half Wave 60Hz Resistive Or Inductive Load FIG.2-TYPICAL FORWARD CURRENT DERATING CURVE 500 INSTANTANEOUS FORWARD CURRENT,(A) 100 40 10 20 40 60 80 100 120 140 160 180 200 CASE TEMPERATURE ( C) 1 FIG.4-MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT,(A) 250 0.1 .6 .8 1.0 1.2 1.4 1.6 1.8 2.0 FORWARD VOLT AGE,(V) 200 FIG.3- TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTICS 50W NONINDUCTIVE 10W NONINDUCTIVE 150 Tj=25 C 8.3ms Single Half Sine Wave JEDEC method 100 50 (+) 25Vdc (approx.) () 1W NONINDUCTIVE OSCILLISCOPE (NOTE 1) D.U.T. () PULSE GENERATOR (NOTE 2) (+) 0 1 5 10 50 100 NUMBER OF CYCLES AT 60Hz NOTES: 1. Rise Time= 7ns max., Input Impedance= 1 megohm.22pF. 2. Rise Time= 10ns max., Source Impedance= 50 ohms. FIG.5-TYPICAL JUNCTION CAPACITANCE 140 120 100 80 60 40 20 trr +0.5A | | | | | | | | 0 -0.25A JUNCTION CAPACITANCE,(pF) -1.0A 1cm SET TIME BASE FOR 50 / 10ns / cm 0 .01 .05 .1 .5 1 5 10 50 100 REVERSE VOLTAGE,(V)