LE05W8J0560T5E

DATA SHEET Product Name Flex Led Strip Use Thick Film Chip Resistors Part Name LE05/LE06 Series Uniroyal Electronics Global Co., Ltd. 88#, Longteng Road, Economic & Technical Development Zone, Kunshan, Jiangsu, China Tel Email Manufacture Plant +86 512 5763 1411 / 22 /33 marketing@uni-royal.cn Uniroyal Electronics Industry Co., Ltd. Aeon Technology Corporation Royal Electronic Factory (Thailand) Co., Ltd. Royal Technology (Thailand) Co., Ltd. Flex Led Strip Use Thick Film Chip Resistors 1. Scope: 1.1 This datasheet is the characteristics of Flex Led Strip Use Thick Film Chip Resistor manufactured by UNI-ROYAL. 1.2 Suit for reflow. 1.3 Stable electrical capability ，high reliability. 1.4 Low assembly cost, suit for automatic SMT equipment 1.5 Superior mechanical strength and high frequency characteristics 1.6 According with ROHS standard and Halogen-free 2. Part No. System Part No. includes 14 codes shown as below: 2.1 1st~4th codes: Part name. E.g.: LE05、LE06 2.2 5th~6th codes: Power rating. E.g.: W=Normal Size “1~G” = “1~16” Wattage 1/32 3/4 1/2 1/3 1/4 1/8 1/10 1/16 1/20 1 Normal Size WH 07 W2 W3 W4 W8 WA WG WM 1W If power rating is equal or lower than 1 watt, 5th code would be “W” and 6th code would be a number or letter. E.g.: WA=1/10W W4=1/4W 2.3 7th code: Tolerance. E.g.: D=±0.5% F=±1% G=±2% J=±5% K= ±10% 2.4 8th~11th codes: Resistance Value. 2.4.1 If value belongs to standard value of E-24 series, the 8th code is zero, 9th~10th codes are the significant figures of resistance value, and the 11th code is the power of ten. 2.4.2 If value belongs to standard value of E-96 series, the 8th~10th codes are the significant figures of resistance value, and the 11th code is the power of ten. 2.4.311th codes listed as following: 0=100 1=101 2=102 3=103 4=104 5=105 6=106 J=10-1 K=10-2 L=10-3 M=10-4 th th 2.5 12 ~14 codes. 2.5.1 12th code: Packaging Type. E.g.: C=Bulk T=Tape/Reel 2.5.2 13th code: Standard Packing Quantity. 4=4,000pcs 5=5,000pcs C=10,000pcs D=20,000pcs E=15,000pcs Chip Product: BD=B/B-20000pcs TC=T/R-10000pcs 2.5.3 14th code: Special features. E = Environmental Protection, Lead Free, or Standard type. 3. Ordering Procedure (Example: LE06 1/4W ±5% 100Ω T/R-5000) L E 0 6 Product Type: Fill-in 4 digits with the chip resistor type as follows: LE05 LE06 W 4 Wattage: W8=1/8W W4=1/4W J 0 1 0 1 T Resistance Value: 5%(E-24 series): The 1st digit will be “0”; the 2nd & 3rd digits are for the significant figures of the resistance and the 4th digit indicate the numbers of zeros following. 1% (E-96 series): The 1st to 3rd digits are for the significant figures of the resistance and 4th digit denotes number of zeros following. 5 E Packing quantity: 5=5000PCS Special Feature E= Lead-Free J=10-1; K=10-2; L=10-3 Tolerance: J=±5% F=±1% Feb.12,2019 V.2 Packing Type: T=Tape/Reel www. uni-royal.cn Page 2/5 Flex Led Strip Use Thick Film Chip Resistors 4. Marking 4.1 ±5% tolerance products (E-24 series): 3 codes. 1st~2nd codes are the significant figures of resistance value, and the rest code is the power of ten 201 → 200Ω 4.2 ±1% tolerance products (E-96 series): 4 codes. 1st~3rd codes are the significant figures of resistance value, and the rest code is the power of ten. Letter "R" in mark means decimal point. 1000 → 100Ω 5. Dimension Type L Dimension(mm) W H A1 B1 LE05(0805) 2.00±0.15 1.25 +0.15/-0.10 0.55±0.10 ≤1.0 0.40±0.20 LE06(1206) 3.10±0.15 1.55 +0.15/ -0.10 0.55±0.10 ≤1.0 0.50±0.20 6. Resistance Range Type 70℃ Power Max Working Voltage Max Overload Voltage LE05 1/8W 200V 400V ±1%,±5% 10Ω~820Ω LE06 1/4W 200V 400V ±1%,±5% 10Ω~820Ω Tolerance Resistance Range 7. Structure 8. Recommend the size of welding plate Dimension(mm) Type LE05 LE06 A B C D 1.0±0.1 2.0±0.1 1.0±0.1 1.1±0.1 1.3±0.1 1.6±0.1 3.0±0.1 4.2±0.1 Feb.12,2019 V.2 www. uni-royal.cn Page 3/5 Flex Led Strip Use Thick Film Chip Resistors 9. Derating Curve Power rating will change based on continuous load at ambient temperature from -55 to 155℃. It is constant between -55 to 70℃, and derate to zero when temperature rise from 70 to 155℃. Voltage rating: Resistors shall have a rated direct-current (DC) continuous working voltage or an approximate sine-wave root-mean-square (RMS) alternating-current (AC) continuous working voltage at commercial-line frequency and waveform corresponding to the power rating, as determined from the following formula: RCWV = √𝑃 × R Remark: RCWV: Rating Continuous Working Voltage (Volt.) P: power rating (Watt) R: nominal resistance (Ω) In no case, the rated DC or RMS AC continuous working voltage must be greater than the applicable maximum value. The overload voltage is 2.5 times RCWV or Max. Overload voltage whichever is lower. 10. Performance Specification Characteristic Temperature Coefficient Test Methods (GB/T5729&JIS-C-5201&IEC60115-1) Limits 4.8 Natural resistance changes per temp. Degree centigrade R 2 -R 1 × 106 (PPM/℃) R 1 (t 2 -t 1 ) R 1 : Resistance Value at room temperature （t 1 ）; R 2 : Resistance at test temperature (Upper limit temperature or Lower limit temperature) t 1: +25°C or specified room temperature t 2: Upper limit temperature or Lower limit temperature test temperature ±200PPM/°C ±1% ±(1.0%+0.1Ω) ±5% ±(2.0%+0.1Ω) Short-time overload Dielectric withstanding voltage 4.13 Permanent resistance change after the application of a potential of 2.5 times RCWV or Max. Overload Voltage whichever less for 5 seconds. No evidence of flashover mechanical damage, arcing or insulation breaks down. 4.7 Resistors shall be clamped in the trough of a 90℃metallic vblock and shall be tested at ac potential respectively specified in the given list of each product type for 60-70 seconds. Coverage must be over 95%. Wave solder: Test temperature of solder: 245℃±3℃ dipping time in solder: 23 seconds. Reflow: Solderability Go up tin rate bigger than half of end pole ±1% ±(1.0%+0.1Ω). Rapid change of temperature 4.19 30 min at lower limit temperature and 30 min at upper limit temperature，100 cycles. ±5% Soldering heat Terminal bending Insulation resistance Feb.12,2019 V.2 ±(3.0%+0.1Ω) Resistance change rate must be in ±(1%+0.005Ω) After electricity, the lamp is not bright ≥1,000 MΩ 4.18 Dip the resistor into a solder bath having a temperature of 260℃±5℃ and hold it for 10±1 seconds. The interception length is a soft light band of 12 resistors, and the force of 0.5kg on the Φ30mm PVC pipe is coiled and reversed five times 4.6 The measuring voltage shall be ,measured with a direct voltage of (100±15)V or a voltage equal to the dielectric withstanding voltage., and apply for 1min. www. uni-royal.cn Page 4/5 Flex Led Strip Use Thick Film Chip Resistors Humidity ( steady state ) Load life in humidity ±1% ±(0.5%+0.1Ω). ±5% ±(3.0%+0.1Ω) ±1% ±(1.0%+0.05Ω). ±5% ±(3.0%+0.05Ω) ±1% ±(1.0%+0.1Ω) ±5% ±(3.0%+0.1Ω) ±1% ±(1.0%+0.1Ω) ±5% ±(3.0%+0.1Ω) ±% ±(1.0%+0.1Ω) ±5% ±(3.0%+0.1Ω) Load life Low Temperature Storage High Temperature Exposure 7.9 Resistance change after 1,000 hours (1.5 hours “ON”,0.5 hour “OFF”) at RCWV in a humidity chamber controlled at 40 ℃±2℃ and 90 to 95% relative humidity. 4.25.1 Permanent resistance change after 1,000 hours operating at RCWV with duty cycle 1.5 hours “ON”, 0.5 hour “OFF” at 70 ℃±2℃ ambient. 4.23.4 Lower limit temperature，for 2H. 4.23.2 Upper limit temperature ，for 16H. J-STD-002 Test D Samples completely immersed for 30 sec in solder bath at 260℃ No visible damage Leaching 4.24Temporary resistance change after 240 hours exposure in a humidity test chamber controlled at 40±2℃ and 90-95% relative humidity, 11. Packing of Surface Mount Resistors 11.1 Dimension of Paper Taping :(Unit: mm) A ±0.2 1.65 2.00 Type LE05 LE06 B ±0.2 2.40 3.60 C ±0.05 2.00 2.00 ΦD+0.1 −0 1.50 1.50 E ±0.1 1.75 1.75 F ±0.05 3.50 3.50 G ±0.1 4.00 4.00 W ±0.2 8.00 8.00 T ±0.1 0.81 0.81 11.2 Dimension of Reel：(Unit: mm) Type Taping Qty/Reel A±0.5 B±0.5 C±0.5 D±1 M±2 W±1 LE05 Paper 5,000pcs 2.0 13.0 21.0 60.0 178.0 10.0 LE06 Paper 5,000pcs 2.0 13.0 21.0 60.0 178.0 10.0 12. Note 12.1. UNI-ROYAL recommend products store in warehouse with temperature between 15 to 35℃ under humidity between 25 to 75%RH. Even under storage conditions recommended above, solder ability of products will be degraded stored over 1 year old. 12.2. Cartons must be placed in correct direction which indicated on carton, otherwise the reel or wire will be deformed. 12.3. Storage conditions as below are inappropriate: a. Stored in high electrostatic environment b. Stored in direct sunshine, rain, snow or condensation. c. Exposed to sea wind or corrosive gases, such as Cl 2 , H 2 S, NH 3 , SO 2 , NO 2 , etc. 13. Record Version Description Page Date Amended by Checked by 1 First version 1~6 Mar.20, 2018 Haiyan Chen Nana Chen 2 Modify characteristic 4~5 Feb.12, 2019 Haiyan Chen Yuhua Xu © Uniroyal Electronics Global Co., Ltd. All rights reserved. Specification herein will be changed at any time without prior notice. Feb.12,2019 V.2 www. uni-royal.cn Page 5/5