SF66

SF61 6.0 AMP SUPER FAST RECTIFIERS THRU SF67 VOLTAGE RANGE 50 to 600 Volts CURRENT FEATURES * Low forward voltage drop * High current capability * High reliability * High surge current capability * Good for switching mode application 6.0 Amperes DO-27 .220(5.6) .197(5.0) DIA. 1.0(25.4) MIN. MECHANICAL DATA * Case: Molded plastic * Epoxy: UL 94V-0 rate flame retardant * Lead: Axial leads, solderable per MIL-STD-202, method 208 guranteed * Polarity: Color band denotes cathode end * Mounting position: Any * Weight: 1.10 grams .375(9.5) .285(7.2) .052(1.3) .048(1.2) DIA. 1.0(25.4) MIN. Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating 25 C ambient temperature uniess otherwies specified. Single phase half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. TYPE NUMBER Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current .375"(9.5mm) Lead Length at Ta=55 C Peak Forward Surge Current, 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Maximum Instantaneous Forward Voltage at 6.0A Maximum DC Reverse Current Ta=25 C at Rated DC Blocking Voltage Ta=100 C Maximum Reverse Recovery Time (Note 1) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range TJ, TSTG NOTES: SF61 50 35 50 SF62 100 70 100 SF63 150 105 150 SF64 200 140 200 6.0 150 SF65 300 210 300 SF66 400 280 400 SF67 UNITS 600 420 600 V V V A A V A A nS pF C 0.95 5.0 50 35 -65 50 +150 1.25 1.50 1. Reverse Recovery Time test condition: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1MHz and applied reverse voltage of 4.0V D.C. RATING AND CHARACTERISTIC CURVES (SF61 THRU SF67) FIG.1- TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC 50W NONINDUCTIVE 10W NONINDUCTIVE trr +0.5A | | | | | | | | FIG.2-TYPICAL FORWARD CURRENT DERATING CURVE AVERAGE FORWARD CURRENT,(A) 6 5 4 3 2 1 0 0 25 50 75 100 125 150 175 Single Phase Half Wave 60Hz Resistive Or Inductive Load 0.375"(9.5mm) Lead Length (+) 25Vdc (approx.) () 1W NONINDUCTIVE OSCILLISCOPE (NOTE 1) D.U.T. () PULSE GENERATOR (NOTE 2) (+) 0 -0.25A NOTES: 1. Rise Time= 7ns max., Input Impedance= 1 megohm.22pF. 2. Rise Time= 10ns max., Source Impedance= 50 ohms. -1.0A 1cm SET TIME BASE FOR 50 / 10ns / cm AMBIENT TEMPERATURE,( C) FIG.3-TYPICAL FORWARD CHARACTERISTICS 50 INSTANTANEOUS FORWARD CURRENT,(A) FIG.4-TYPICAL REVERSE CHARACTERISTICS 50 3.0 1.0 SF6 1 ~S F64 SF 6 5~ SF 66 REVERSE LEAKAGE CURRENT, ( A) 10 10 3.0 1.0 Tj=100 C SF 67 0.1 Tj=25 C Pulse Width 300us 1% Duty Cycle Tj=25 C 0.1 .01 .4 .6 .8 1.0 1.2 1.4 1.6 1.8 .01 0 20 40 60 80 100 120 140 FORWARD VOLT AGE,(V) PERCENT OF RATED PEAK REVERSE VOLT AGE,(%) FIG.5-MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT,(A) 150 FIG.6-TYPICAL JUNCTION CAPACITANCE 175 150 125 100 75 50 25 0 120 90 Tj=25 C 8.3ms Single Half Sine Wave JEDEC method 60 30 0 1 5 10 50 100 JUNCTION CAPACITANCE,(pF) .01 .05 .1 .5 1 5 10 50 100 NUMBER OF CYCLES AT 60Hz REVERSE VOLTAGE,(V)