SMH102M

SMH101M THRU SMH107M 1.0 AMP SURFACE MOUNT HIGH EFFICIENCY RECTIFIERS VOLTAGE RANGE 50 to 800 Volts CURRENT FEATURES * Ideal for surface mount applications * Easy pick and place * Built-in strain relief * Fast switching speed 1.0 Ampere SOD-123 0.161(4.1) 0.146(3.7) 0.071(1.8) 0.055(1.4) MECHANICAL DATA * Case: Molded plastic * Epoxy: UL 94V-0 rate flame retardant * Metallurgically bonded construction * Polarity: Color band denotes cathode end * Mounting position: Any * Weight: 0.04 grams 0.035(0.9) 0.067(1.7) 0.060(1.5) 0.035(0.9) Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating 25 C ambient temperature uniess otherwies specified. Single phase half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. TYPE NUMBER Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current .375"(9.5mm) Lead Length at TA=50 C Peak Forward Surge Current, 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Maximum Instantaneous Forward Voltage at 1.0A Maximum DC Reverse Current Ta=25 C at Rated DC Blocking Voltage Ta=100 C Maximum Reverse Recovery Time (Note 1) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range TJ, TSTG NOTES: SMH101M SMH102M SMH103M SMH104M SMH105M SMH106M SMH107M UNITS V V V A A V A A nS pF C 50 35 50 100 70 100 200 140 200 300 210 300 1.0 30 400 280 400 600 420 600 800 560 800 1.0 5.0 100 50 -65 1.3 1.7 75 15 +150 1. Reverse Recovery Time test condition: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1MHz and applied reverse voltage of 4.0V D.C. RATING AND CHARACTERISTIC CURVES (SMH101M THRU SMH107M) FIG.1-TYPICAL FORWARD CHARACTERISTICS AVERAGE FORWARD CURRENT,(A) FIG.2-TYPICAL FORWARD CURRENT DERATING CURVE 10 1.2 1.0 0.8 0.6 0.4 0.2 0 0 20 40 60 80 100 120 140 160 180 200 Single Phase Half Wave 60Hz Resistive Or Inductive Load INSTANTANEOUS FORWARD CURRENT,(A) 103 M M 01 M ~S MH 05 SM H1 04 SM H1 0.1 Tj=25 C Pulse Width 300us 1% Duty Cycle SM H 10 6M ~S M H 1.0 M~ SM H1 10 7M LEAD TEMPERATURE ( C) 0.01 FIG.4-MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PEAK FORWAARD SURGE CURRENT,(A) 50 .001 .4 .6 .8 1.0 1.2 1.4 1.6 1.8 FORWARD VOLT AGE,(V) 40 FIG.3- TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTICS 50W NONINDUCTIVE 10W NONINDUCTIVE 30 Tj=25 C 8.3ms Single Half Sine Wave JEDEC method 20 10 (+) 25Vdc (approx.) () 1W NONINDUCTIVE OSCILLISCOPE (NOTE 1) D.U.T. () PULSE GENERATOR (NOTE 2) (+) 0 1 5 10 50 100 NUMBER OF CYCLES AT 60Hz NOTES: 1. Rise Time= 7ns max., Input Impedance= 1 megohm.22pF. 2. Rise Time= 10ns max., Source Impedance= 50 ohms. FIG.5-TYPICAL JUNCTION CAPACITANCE 35 30 25 20 15 10 5 trr +0.5A | | | | | | | | 0 -0.25A JUNCTION CAPACITANCE,(pF) -1.0A 1cm SET TIME BASE FOR 50 / 10ns / cm 0 .01 .05 .1 .5 1 5 10 50 100 REVERSE VOLTAGE,(V)