MOF-T2C2

Fiber Optic Transmitter Features 1.Compact (adoption of small jack for mini plug JIS C6560) 2.Thin type (4.4mm) transmitter unit. 3.Both optical and electrical signal can be distinguished and transmitted. 4.Signal transmission speed : MAX. 12.5 Mbps (NRZ signal) 5.Operating voltage : 4.75 to 5.25 V 6.L/F pitch : 2.0 mm MOF-T2C2 Outline Dimensions Jack terminal configuration 1 2 3 4 5 6 7 8 9 10 jack terminal device terminal Internal equivalent circuit NOTES: Tolerance is ±0.3mm unless otherwise noted. Absolute Maximum Ratings (Photoelectric conversion element) Parameter Supply voltage Input voltage Operating temperature Storage temperature Soldering temperature *1 For 5s (2 times or less) *1 @TA=25oC Symbol Vcc Vin Topr Tstg Tsol Rating -0.5 to + 7.0 -0.5 to Vcc +0.5 -20 to +70 -30 to +80 260 Unit V V C C o C o o Absolute Maximum Rating(Jack) Parameter Total power dissipation Operating temperature Storage temperature Soldering temperature Isolation voltage *1 For 5s (2 times or less) *2 For 1 min *2 *1 Symbol Ptot Topr Tstg Tsol Viso Rating D.C. 12V, 1A -20 to +70 -30 to +80 260 A.C. 500V rms Unit - C C o C o o - REV : A1 Unity Opto Technology Co., Ltd. 01/08/2002 1/4 Fiber Optic Transmitter MOF-T2C2 Recommended Operating Conditions Parameter Operating supply voltage Operating transfer rate Symbol Vcc T MIN. 4.75 --- TYP. 5.0 --- MAX. 5.25 12.5 Unit V Mbps Electro-Optical Characteristics Parameter Peak emission wavelength Optical power output coupling with fiber Dissipation current High level input voltage Low level input voltage Low to High delay time High to Low delay time Pulse width distortion Symbol λp Pc Icc ViH ViL tpLH tpHL ∆tw Conditions Refer to Fig. 1 Refer to Fig. 2 Refer to Fig. 2 Refer to Fig. 2 Refer to Fig. 3 Refer to Fig. 3 Refer to Fig. 3 MIN. 630 -21 --2.1 -------15 TYP. 660 -18 8 ----------- MAX. 690 -15 13 Vcc 0.8 180 180 +15 Unit nm dBm mA V V ns ns ns REV : A1 Unity Opto Technology Co., Ltd. 01/08/2002 2/4 Fiber Optic Transmitter MOF-T2C2 Fig. 1 Measuring Method of Optical Output Coupling with Fiber Standard optical fiber cable MOF-T2C2 Unit to be measured Vin VCC Optical power meter GND The optical power meter must be calibrated to have the wavelength sensitivity of 660 nm. ( 0dBm=1mW ) D VCC Notes (1)Vcc=5.0V (State of operating) (2)To bundle up the standard fiber optic cable, make it into a loop with the diameter D=10cm or more. Fig. 2 Measuring Method of Intput Voltage and Supply Current Standard optical fiber cable MOF-T2C2 Unit to be measured Vin VCC GND The optical power meter must be calibrated to have the wavelength sensitivity of 660 nm. ( 0dBm=1mW ) Vin Icc VCC Input conditions and judgement method Conditions Vin=2.1V or more Vin=0.8V or less Note: Vcc=5.0V (State of operating) Judgement method -21dBm