75185-S20-R

UNISONIC TECHNOLOGIES CO., LTD 75185 MULTIPLE RS-232 DRIVERS AND RECEIVERS DESCRIPTION The UTC 75185 complies with the requirements of the TIA/EIA232-F and ITU (formerly CCITT) v.28 standards. These standards are for data interchange between a host computer and peripheral at signaling rates up to 20kbit/s. The switching speeds of the UTC 75185 are fast enough to support rates up to 120kbite/s with lower capacitive loads (shorter cables). Interoperability at the higher signaling rates cannot be assured unless the designer has design control of the cable and the interface circuits at both ends. For interoperability at signaling rates to 120kbit/s, use of ITA/EIA-423-B (ITU v.10) and TIA/EIA-422-B (ITU v.11) standards are recommended. LINEAR INTEGRATED CIRCUIT TSSOP-20 SSOP-20 SOP-20 DIP-20 FEATURES *Single Chip with Easy Interface between UART and Serial-Port connector of PC. *Three Drivers and five Receivers Meet or Exceed the Requirements of TIA/EIA-232-F and ITU v.28 Standards. *Designed to Support Data Rates up to 120 kbps ORDERING INFORMATION Normal 75185-D20-T 75185-P20-R 75185-R20-R 75185-S20-R Ordering Number Lead Free Plating 75185L-D20-T 75185L-P20-R 75185L-R20-R 75185L-S20-R Halogen Free 75185G-D20-T 75185G-P20-R 75185G-R20-R 75185G-S20-R Package DIP-20 TSSOP-20 SSOP-20 SOP-20 Packing Tube Tape Reel Tape Reel Tape Reel www.unisonic.com.tw Copyright © 2010 Unisonic Technologies Co., Ltd 1 of 10 QW-R113-003,F 75185 PIN CONFIGURATIONS VDD RA1 RA2 RA3 DY1 DY2 RA4 DY3 RA5 VSS 1 2 3 4 5 6 7 8 9 10 LINEAR INTEGRATED CIRCUIT 20 19 18 17 16 15 14 13 12 11 VCC RY1 RY2 RY3 DA1 DA2 RY4 DA3 RY5 GND PIN DESCRIPTION PIN NO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 SYMBOL VDD RA1 RA2 RA3 DY1 DY2 RA4 DY3 RA5 VSS GND RY5 DA3 RY4 DA2 DA1 RY3 RY2 RY1 VCC PIN DESCRIPTION Supply Voltage First Receiver Input Second Receiver Input Third Receiver Input First Driver Output Second Driver Output Fourth Receiver Input Third Driver Output Fifth Receiver Input Supply Voltage Ground Fifth Receiver Output Third Driver Input Fourth Receiver Output Second Driver Input First Driver Input Third Receiver Output Second Receiver Output First Receiver Output Supply Voltage UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 2 of 10 QW-R113-003,F 75185 PARAMETER Supply Voltage (Note 1) Input Voltage Range Driver Output Voltage Range Receiver Low Level Output Current Storage Temperature Range Drive Receiver SYMBOL VDD VSS VCC VIN VOUT IOUT TSTG LINEAR INTEGRATED CIRCUIT ABSOLUTE MAXIMUM RATINGS OVER OPERATING FREE-AIR TEMPERATURE RANGE (unless otherwise specified) RATINGS 15 -15 10 -15 ~ 7 -30 ~ 30 -15~ 15 20 -65 ~ +150 UNIT V V V V V V mA °C THERMAL DATA PARAMETER DIP-20 Junction to Ambient SYMBOL RATINGS 70 UNIT SOP-20 100 θJA °C/W SSOP-20 115 TSSOP-20 115 Note 1: All voltage are with respect to the network ground terminal. Note 2: The package thermal impedance is calculated in accordance with JESD 51, except for through-hole packages, which use a trace length of zero. RECOMMENDED OPERATING CONDITIONS PARAMETER Supply Voltage Input Voltage (Driver Only) High Level Output Current Low Level Output Current Operating Free-Air Temperature High Level Low Level Drive Receiver Drive Receiver SYMBOL VDD VSS VCC VIH VIL IOH IOL TA 0 MIN 7.5 -7.5 4.5 1.9 TYP 9 -9 5 MAX 15 -15 5.5 0.8 -6.0 -0.5 6 16 70 UNIT V V V V V mA mA °C SUPPLY CURRENTS PARAMETER SYMBOL TEST CONDITIONS VDD VSS 9 -9 No load. 12 -12 All inputs at 1.9V 15 -15 9 -9 No load. 12 -12 All inputs at 0.8V 15 -15 9 -9 No load. 12 -12 All inputs at 1.9V 15 -15 9 -9 No load. 12 -12 All inputs at 0.8V 15 -15 No load. All inputs at 5V, VCC=5V MIN MAX 15 19 25 4.5 5.5 9 -15 -19 -25 -3.2 -3.2 -3.2 30 UNIT mA Supply Current From VDD IDD mA mA Supply Current From VSS ISS mA mA Supply Current From VCC ICC UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 3 of 10 QW-R113-003,F 75185 LINEAR INTEGRATED CIRCUIT DRIVER ELECTRICAL CHARACTERISTICS OVER RECOMMENDED OPERATING FREE-AIR TEMPERATURE RANGE (VDD=9V, VSS=-9V, VCC=5V, unless otherwise specified) PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNIT High Level Output Voltage VOH VIL =0.8V, RL =3 kΩ (Figure 1) 6 7.5 V Low Level Output Voltage (Note 3) VOL VIH =1.9V, RL =3 kΩ (Figure 1) -7.5 -6 V High Level Input Current IIH VIN =5V (Figure 2) 10 μA Low Level Input Current IIL VIN =0V (Figure 2) -1.6 mA High Level Short Circuit Output Current IOS(H) VIL =0.8V, VOUT =0V(Figure 1) -4.5 -12 -19.5 mA (Note 4) Low Level Short Circuit Output Current IOS(L) VIH =2V, VOUT =0V(Figure 1) 4.5 12 19.5 mA Output Resistance (Note 5) ROUT VDD =VSS=VCC=0V, VOUT =-2 to 2V 300 Ω Note 3: The algebraic convention, where the more positive (less negative) limit is designated as maximum, is used in this datasheet for logic levels only (e.g. if -10V is a maximum, the typical value is a more negative voltage). Note 4: Output short circuit conditions must maintain the total power dissipation below absolute maximum ratings. Note 5: Test conditions are those specified by TIA/EIA232-F and as listed above. DRIVER SWITCHING CHARACTERISTICS (VDD=12V, VSS=-12V, VCC=5V, TA=25°C) PARAMETER Propagation Delay Time Level Low to High Output High to Low SYMBOL TEST CONDITIONS MIN TYP MAX UNIT tPLH RL=3 to 7 kΩ, CL=15pF (Figure 3) 315 500 ns RL=3 to 7 kΩ, CL=15pF (Figure 3) tPHL 75 175 ns RL=3 to 7 kΩ, CL=15pF (Figure 3) 60 100 ns Transition Time Level Output Low to High tTLH RL=3 to 7 kΩ, CL=2500pF 1.7 2.5 μs (Note 6,Figure 3) RL=3 to 7 kΩ, CL=15pF (Figure 3) 40 75 ns Transition Time Level Output High to Low tTHL RL=3 to 7 kΩ, CL=2500pF 1.5 2.5 μs (Note 7, Figure 3) Note 6: Measured between -3V and 3V points of the output waveform (TIA/EIA-232-F conditions), all unused inputs are tied. Note 7: Measured between 3V and -3V points of the output waveform (TIA/EIA-232-F conditions), all unused inputs are tied. RECEIVER ELECTRICAL CHARACTERISTICS OVER RECOMMENDED OPERATING CONDITIONS (TA=25°C, VCC=5V, VDD=9V, VSS=-9V) PARAMETER Positive Going Threshold Voltage Negative Going Threshold Voltage Input Hysteresis (VT+ - VT-) Output Voltage High level Low level High level Input Current Low level Short-Circuit Output Current IIL IOS SYMBOL VT + VT VHYS VOH VOL IIH VIH=0.75V Inputs Open VIN=3V, IOL=10mA VIN=25V (Figure 5) VIN=3V (Figure 5) VIN=-25V (Figure 5) VIN=-3V (Figure 5) IOH=-0.5mA (Figure 4) TEST CONDITIONS (Figure 5) TA=25°C TA=0°C to 70°C MIN 1.75 1.55 0.75 0.5 2.6 2.6 3.6 0.43 -3.6 -0.43 -3.4 TYP 1.9 0.97 4 0.2 MAX 2.3 2.3 1.25 5 0.45 8.3 -8.3 -12 UNIT V V V V V mA mA mA RECEIVER SWITCHING CHARACTERISTICS (VDD=12V, VSS=-12V, VCC=5V, TA=25°C) PARAMETER Propagation Delay Time Level Output Transition Time Level Output Low to High High to Low Low to High High to Low SYMBOL TEST CONDITIONS RL=5 kΩ, CL=50pF tPLH (Figure 6) tPHL tTLH tTHL MIN TYP 107 42 175 16 MAX 500 150 525 60 UNIT ns ns ns ns 4 of 10 QW-R113-003,F UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 75185 PARAMETER MEASUREMENT INFORMATION DRIVER TEST CIRCUITS: LINEAR INTEGRATED CIRCUIT Figure 1. For VOH, VOL, IOS(H), IOS(L) Figure 2. For IIH, IIL DRIVER VOLTAGE WAVEFORMS: Figure 3. Note 1. The pulse generator has the following characteristics: tw=25μs, PRR=20kHz, Zo=50Ω, tr=tf