75232L-S20-T

UNISONIC TECHNOLOGIES CO., LTD 75232 MULTIPLE RS-232 DRIVERS AND RECEIVERS DESCRIPTION The UTC 75232 is a monolithic IC containing three independent drivers and five receivers which comply with the requirements of the TIA/EIA232-F standards. LINEAR INTEGRATED CIRCUIT FEATURES * Single chip with easy interconnection of the UART and serial-port connector of personal computer. * Meets standard TIA/EIA-232-F and ITU V.28 * Up to 120 kbps data rate * 20-pin SOP/ DIP/SSOP/TSSOP packages *Pb-free plating product number: 75232L ORDERING INFORMATION Ordering Number Normal Lead Free Plating 75232-D20-T 75232L-D20-T 75232-P20-R 75232L-P20-R 75232-P20-T 75232L-P20-T 75232-R20-R 75232L-R20-R 75232-R20-T 75232L-R20-T 75232-S20-R 75232L-S20-R 75232-S20-T 75232L-S20-T Package DIP-20 TSSOP-20 TSSOP-20 SSOP-20 SSOP-20 SOP-20 SOP-20 Packing Tube Tape Reel Tube Tape Reel Tube Tape Reel Tube 75232L-D20-T (1)Packing Type (2)Package Type (3)Lead Plating (1) R: Tape Reel, T: Tube (2) D20: DIP-20, S20: SOP-20, R20: SSOP-20, P20: TSSOP-20 (3) L: Lead Free Plating, Blank: Pb/Sn www.unisonic.com.tw Copyright © 2005 Unisonic Technologies Co., Ltd 1 of 10 QW-R113-005,D 75232 PIN CONFIGURATION VDD RA1 RA2 RA3 DY1 DY2 RA4 DY3 RA5 VSS 1 2 3 4 5 6 7 8 9 10 LINEAR INTEGRATED CIRCUIT 20 19 18 17 16 15 14 13 12 11 VCC RY1 RY2 RY3 DA1 DA2 RY4 DA3 RY5 GND PIN DESCRIPTION PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 PIN NAME VDD RA1 RA2 RA3 DY1 DY2 RA4 DY3 RA5 VSS GND RY5 DA3 RY4 DA2 DA1 RY3 RY2 RY1 VCC FUNCTION Supply Voltage First Receiver Input Second Receiver Input Third Receiver Input First Driver Output Second Driver Output Fourth Receiver Input Third Driver Output Fifth Receiver Input Supply Voltage Ground Fifth Receiver Output Third Driver Input Fourth Receiver Output Second Driver Input First Driver Input Third Receiver Output Second Receiver Output First Receiver Output Supply Voltage UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 2 of 10 QW-R113-005,D 75232 ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL VDD VSS VCC LINEAR INTEGRATED CIRCUIT RATINGS 15 -15 10 -15 ~ 7 -30 ~ 30 -15 ~ 15 UNIT V Supply Voltage (Note 2) V V Driver V Input Voltage Range VIN Receiver V Driver Output Voltage Range VOUT V Receiver Low Level Output Current IOUT 20 mA Operation Temperature TOPR 0 ~ +70 °C Storage Temperature TSTG -40 ~ +150 °C Note: 1.Absolute maximum ratings are those values beyond which the device could be permanently damaged. Absolute maximum ratings are stress ratings only and functional device operation is not implied. 2. All voltages are with respect to the network ground terminal. THERMAL DATA PARAMETER DIP-20 Thermal Resistance Junction- Ambient SOP-20 SSOP-20 TSSOP-20 θJA SYMBOL RATINGS 70 100 115 115 UNIT °C/W RECOMMENDED OPERATING RATINGS PARAMETER Supply Voltage Level Input Voltage (driver only) High Level Output Current Low Level Output Current Operating Free-air Temperature High Low Driver Receiver Driver Receiver SYMBOL VDD VSS VCC VIH VIL IOH IOL TOPR 0 MIN 7.5 -7.5 4.5 1.9 TYP 9 -9 5 MAX 15 -15 5.5 0.8 -6.0 -0.5 6 16 70 UNIT V V V V V mA mA °C E LECTRICAL CHARACTERISTICS (Over recommended supply voltage and operating temperature ranges, unless otherwise specified) PARAMETER SUPPLY CURRENTS SYMBOL TEST CONDITIONS VDD =9V, VSS =-9V No load. VDD =12, VSS =-12V All inputs at 1.9V VDD =15, VSS =-15V VDD =9V, VSS =-9V No load. VDD =12, VSS =-12V All inputs at 0.8V VDD =15, VSS =-15V VDD =9V, VSS =-9V No load. VDD =12, VSS =-12V All inputs at 1.9V VDD =15, VSS =-15V VDD =9V, VSS =-9V No load. VDD =12, VSS =-12V All inputs at 0.8V VDD =15, VSS =-15V No load. All inputs at 5V, VCC=5V MIN TYP MAX 15 19 25 4.5 5.5 9 -15 -19 -25 -3.2 -3.2 -3.2 30 UNIT mA Supply Current from VDD IDD mA mA Supply Current from VSS ISS mA mA Supply Current from VCC ICC UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 3 of 10 QW-R113-005,D 75232 ELECTRICAL CHARACTERISTICS(Cont.) LINEAR INTEGRATED CIRCUIT DRIVER SECTION (VDD=9V, VSS=-9V, VCC=5V) Output Voltage Level High VOH VIL=0.8V, RL=3 kΩ 6 7.5 V (Figure. 1) Low VOL VIH=1.9V, RL=3 kΩ (Note 1) -7.5 -6 V Input Current Level High IIH VIN=5V 10 μA (Figure. 2) Low IIL VIN=0V -1.6 mA Short Circuit Output Current High IOS(H) VIL=0.8V, VOUT=0V (Note 2) -8.5 -12 -19.5 mA (Figure. 1) Low IOS(L) VIH=2.0V, VOUT=0V 8.5 12 19.5 mA Output Resistance (Note 3) ROUT VDD=VSS=VCC=0V, VOUT=-2V~2V 300 Ω RECEIVER SECTION (VDD=9V, VSS=-9V, VCC=5V) Ta=25°C (Figure. 5) 1.75 1.9 2.3 Positive VT+ V Going Threshold Voltage Ta=0°C ~ 70°C (Figure. 5) 1.55 2.3 Negative VT0.75 0.97 1.25 V Input Hysteresis(VT+ - VT-) VHYS 0.5 V VIH=0.75V 2.6 4 5 High VOH IOH=-0.5mA V Output Voltage Level Inputs Open 2.6 Low VOL VIN=3V, IOL=10mA 0.2 0.45 V VIN=25V 3.6 8.3 High IIH mA Input Current Level VIN=3V 0.43 (Figure. 5) VIN=-25V -3.6 -8.3 Low IIL mA -0.43 VIN=-3V Short-Circuit Output Current IOS (Fig. 4) -3.4 -12 mA Note. 1. For voltage logic levels, the more positive (less negative) limit is designated as maximum, (e.g. if -10V is a maximum, the typical value is a more negative voltage). 2: Output short circuit conditions must maintain the total power dissipation below absolute maximum ratings and the sign is used to indicate direction. 3: Test conditions are those specified by TIA/EIA232-F and as listed above. SWITCHING CHARACTERISTICS (Ta=25°C) PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX DRIVER SECTION (VDD=12V, VSS=-12V, VCC=5V) Low to High tPLH 315 500 RL=3 ~ 7 kΩ, CL=15pF Propagation Delay Time (Figure. 3) 75 175 High to low tPHL Low to High tTLH 60 100 RL=3 ~ 7 kΩ, CL=15pF High to Low tTHL 40 75 Transition Time RL=3 ~ 7 kΩ, CL=2500pF Low to High tTLH 1.7 2.5 (Figure. 3, Note) High to Low tTHL 1.5 2.5 RECEIVER SECTION (VDD=12V, VSS=-12V, VCC=5V) Low to High tPLH 107 250 RL=5 kΩ, CL=50pF High to low tPHL 42 150 Propagation Delay Time (Figure. 6) Low to High tPLH 100 160 RL=1.5 kΩ, CL=15pF High to Low tPHL 60 100 Low to High tTLH 175 350 RL=5 kΩ, CL=50pF 16 60 High to Low tTHL Transition Time (Figure. 6) Low to High tTLH 90 175 RL=1.5 kΩ, CL=15pF High to Low tTHL 15 50 Note: Measured points of the output waveform (TIA/EIA-232-F conditions) as below, all unused inputs are tied. - Low to High level: between -3V and 3V. - High to Low level: between 3V and -3V. UNIT ns ns ns ns μs μs ns ns ns ns ns ns ns ns UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 4 of 10 QW-R113-005,D 75232 PARAMETER MEASUREMENT INFORMATION DRIVER TEST CIRCUITS: LINEAR INTEGRATED CIRCUIT IIH VIN -IIL VIN VDD VCC VSS Figure. 1 For VOH, VOL, IOS(H), IOS(L) Figure. 2 For IIH, IIL DRIVER VOLTAGE WAVEFORMS: Figure. 3 Note: 1. The pulse generator characteristics: tW=25μs, PRR=20kHz, ZO=50Ω, tR=tF