MC34119L-D08-T

UNISONIC TECHNOLOGIES CO., LTD MC34119 LINEAR INTEGRATED CIRCUIT LOW POWER AUDIO AMPLIFIER  DESCRIPTION The UTC MC34119 is a low power audio amplifier IC intended for the telephone applications, such as in speakerphones. It provides differential speaker outputs to maximize output swing at low supply voltages. Coupling capacitor to the speaker is not required. Open loop gain is 80dB, and the closed loop gain is set with two external resistors. The Mute pin permits powering down and/or muting the input signal.  FEATURES * Wide operating supply voltage: VCC=2V~16V * Low quiescent supply current (ICC=2.7mA, typ) * Medium power output over 250mW at VCC=6V, RL=32Ω, THD＜10% * Load impedance range (8Ω~100Ω) * Low total harmonic distortion (0.5% typ) * Mute function (ICC=65μA, typ) * Minimum number of external parts required  ORDERING INFORMATION Ordering Number Lead Free MC34119L-D08-T - Halogen Free MC34119G-D08-T MC34119G-S08-R MC34119G-P08-R MC34119G-K08-3030-R MC34119L-D08-T (1)Packing Type (2)Package Type (3)Green Package www.unisonic.com.tw Copyright © 2016 Unisonic Technologies Co., Ltd Package Packing DIP-8 SOP-8 TSSOP-8 DFN-8(3×3) Tube Tape Reel Tape Reel Tape Reel (1) T: Tube, R: Tape Reel (2) D08: DIP-8, S08: SOP-8, P08: TSSOP-8 K08-3030: DFN-8(3×3) (3) L: Lead Free, G: Halogen Free and Lead Free 1 of 8 QW-R107-038.J MC34119  LINEAR INTEGRATED CIRCUIT MARKING DIP-8 SOP-8 TSSOP-8 DFN-8(3×3) UTC MC34119G Date Code Lot Code  PIN CONFIGURATION  PIN DESCRIPTION PIN NO. 1 2 3 4 5 6 7 8 PIN NAME DESCRIPTION This pin can be used to power down the IC to converse power, or for muting, or both. When Mute at a logic “LOW” (less than 0.8V), the IC is enabled for normal operation. When at a logic “HIGH” (2V to VCC), the IC is disabled. If Mute is open, that is equivalent to a logic “LOW”. Ripple A capacitor at this pin increase power supply rejection, and affects turn-on time. This pin Rejection can be left open if the capacitor at pin 3 is sufficient. Analog Ground for the amplifiers. A 1μF capacitor at this pin (with a 5μF capacitor at pin 2) Input(+) provides 52dB( typ) of power supply rejection. Turn-on time of the circuit is affected by the capacitor on this pin. This pin can be used as an alternative input. Amplifier input. The input capacitor and resistor set low frequency roll-off and input Input(-) impedance. The feedback resistor is connected between this pin and output 1. Output 1 Amplifier output 1. The DC level is about (VCC~0.7V)/2. VCC DC supply voltage is applied to this pin (VCC=2~16V). GND Ground pin. Amplifier output 2. This signal is equal in amplitude, but 180°out of phase with that output 1, Output 2 the DC level is about (Vcc~0.7V)/2. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 2 of 8 QW-R107-038.J MC34119  LINEAR INTEGRATED CIRCUIT BLOCK DIAGRAM IN- 4 Amp 1 IN+ VCC 5 OUT1 8 OUT2 1 MUTE 3 6 Bias 2 7 RR GND UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 3 of 8 QW-R107-038.J MC34119  LINEAR INTEGRATED CIRCUIT ABSOLUTE MAXIMUM RATINGS (TA=25C, unless otherwise specified) PARAMETER SYMBOL RATINGS UNIT Supply Voltage VCC -1 ~ +18 V ±250 Output Current IOUT mA Maximum Input, Ripple Rejection, Mute Pin Voltage VIN -1 ~ +1 V Applied Output Voltage (Output Pin When Disabled) VOUT -1 ~ +1 V Junction Temperature TJ +125 C Operating Temperature TOPR -20 ~ +85 C Storage Temperature TSTG -40 ~ +150 C Note: Absolute maximum ratings are those values beyond which the device could be permanently damaged. Absolute maximum ratings are stress ratings only and functional device operation is not implied.  RECOMMENDED OPERATION CONDITIONS (TA=25C, unless otherwise specified) PARAMETER Supply Voltage Load Impedance Peak Load Current Differential Gain (5KHz Bandwidth) Voltage at Mute Ambient Temperature  SYMBOL VCC ZL IL(PEAK) GV VI(MUTE) TA RATINGS 2~16 8~100 ±200 0~46 0~VCC -20~+70 UNIT V Ω mA dB V C ELECTRICAL CHARACTERISTICS (VCC=6V, TA=25C, unless otherwise specified) PARAMETER DC PARAMETER SYMBOL Operating Current Output Voltage ICC VOUT Output Offset Voltage Output High Level Output Low Level Input Bias Current VO(OFF) VOH VOL II(BIAS) Equivalent Resistance REQ AC PARAMETER Open Loop Gain of Amp. 1 Open Loop Gain of Amp. 2 GV1 GV2 Output Power POUT Total Harmonic Distortion (f=1KHz) THD Gain Bandwidth Product GBW Power Supply Rejection (VCC=6V, VCC=3V) RR Muting GV(MUTE) TEST CONDITIONS VCC=3V, Mute=0.8V VCC=16V, Mute=0.8V VCC=3V, Mute=2V RL=16Ω, R1=75KΩ, VCC=3V RL=16Ω, R1=75KΩ, VCC=6V RL=16Ω, R1=75KΩ, VCC=12V VCC=6V, RF=75KΩ,RL=32Ω 2V