TA31001G-D08-T

UNISONIC TECHNOLOGIES CO., LTD TA31001 TELEPHONE TONE RINGER DESCRIPTION The UTC TA31001 is a bipolar integrated circuit designed for telephone bell replacement. It can also be used as alarms or other alerting devices. LINEAR INTEGRATED CIRCUIT FEATURES *Designed for Telephone Bell Replacement. *Low Current Drain for Multiple Extension of Lines. *Adjustable 2-Frequency Tone. *Adjustable Warbling Rate. *Built-in Hysteresis Prevents False Triggering and Rotary Dial 'CHIRPS'. *Programmable for Initiation Voltage by Simple External Resistor. DIP-8 ORDERING INFORMATION Ordering Number Lead Free Halogen Free TA31001L-D08-T TA31001G-D08-T Package DIP-8 Packing Tube www.unisonic.com.tw Copyright © 2010 Unisonic Technologies Co.,LTD 1 of 6 QW-R108-003.C TA31001 PIN CONFIGURATIONS LINEAR INTEGRATED CIRCUIT Vcc 1 8 Output High Freq. Time Constant High Freq. Time Constant GND RSL Low Freq. Time Constant Low Freq. Time Costant 2 7 3 6 4 5 UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 2 of 6 QW-R108-003.C TA31001 BLOCK DIAGRAM R1 C2 R2 LINEAR INTEGRATED CIRCUIT 4 7 6 3 C1 LOW OSC HIGH OSC AMP 8 OUTPUT 1 POWER SUPPLY (WITH HYSTERESIS) 5 2 Note:R1,R2,C1 and C2 are parts externally mounted UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 3 of 6 QW-R108-003.C TA31001 ABSOLUTE MAXIMUM RATINGS (Ta=25°C) PARAMETER Supply Voltage Power Dissipation Ambient Operating Temperature Storage Temperature SYMBOL VCC PD TOPR TSTG LINEAR INTEGRATED CIRCUIT VALUE 30 800 -45 to 85 -65 to 150 UNIT V mW °C °C ELECTRICAL CHARACTERISTICS (Ta=25°C) (All voltage referenced to GND unless otherwise specified) PARAMETER SYMBOL TEST CONDITIONS Operating Supply Voltage VCC Initiation Supply Voltage (Note 1) VSI Initiation Supply Current (Note 1) ISI 6.8K-Pin 2 to GND Sustaining Voltage (Note 2) VSUS See Fig.1 Sustaining Current (Note 2) ISUS No Load VCC=VSUS Trigger Voltage (Note 3) VTRG VCC=15V Trigger Current (Note 3) ITRG VDIS IDIS VOH VCC=15V Disable Voltage (Note 4) Disable Current (Note 4) Output Voltage High MIN 17 1.4 9.7 0.7 9 10 -40 TYP 19 3.5 11 1.4 10.5 20 -50 21 1.6 500 500 563 704 11 MAX 29 21 4.2 12 2.5 12 10005 0.8 UNIT V V mA V mA V μA V μA V V nA nA Hz Hz Hz VCC=21V, I8=-15mA 17.0 19 Pin6=6V, Pin7=GND VCC=21V, I8=15mA Output Voltage Low VOL Pin6=GND, Pin7=6V Input Current 1 IIN(Pin 3) Pin3=6V, Pin4=GND Input Current 2 IIN(Pin 7) Pin7=6V, Pin6=GND High Frequency 1 FH1 R3=191K, C3=6800pF 461 512 High Frequency 2 FH2 R3=191K, C3=6800pF 576 640 Low Frequency FL R2=165K, C2=0.47μF 9 10 Note 1. Initiation supply voltage (VSI) is the supply voltage required to start the tone ringer oscillating. 2. Sustaining voltage (VSUS) is the supply voltage required to maintain oscillation. 3. VTR and ITR are the conditions applied to trigger in to start oscillation for VSUS≦VCC≦VSI 4. VDLS and IDIS are the conditions applied to trigger in to inhibit oscillation for VSI≦VCC 5. Trigger current must be limited to this value externally. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 4 of 6 QW-R108-003.C TA31001 TYPICAL CHARACTERISTICS LINEAR INTEGRATED CIRCUIT Icc(mA),Supply Current UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw Supply Current (mA) 5 of 6 QW-R108-003.C TA31001 APPLICATION CIRCUIT LINEAR INTEGRATED CIRCUIT Figure 1 UTC assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all UTC products described or contained herein. UTC products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 6 of 6 QW-R108-003.C