TL082G-P08-R

UNISONIC TECHNOLOGIES CO., LTD TL082 GENERAL PURPOSE DUAL J-FET OPERATIONAL AMPLIFIER DESCRIPTION The UTC TL082 is a high speed J-FET input dual operational amplifier. It incorporates well matched, high voltage J-FET and bipolar transistors in a monolithic integrated circuit. The device features high slew rates, low input bias and offset current, and low offset voltage temperature coefficient. LINEAR INTEGRATED CIRCUIT FEATURES * Low input bias and offset current * Wide common-mode (up to VCC+ ) and differential voltage range * Output short-circuit protection * High input impedance J-FET input stage * Internal frequency compensation * Latch up free operation * High slewrate:16V/µs(typ.) Lead-free: TL082L Halogen-free:TL082G ORDERING INFORMATION Normal TL082-D08-T TL082-P08-R TL082-S08-R Ordering Number Lead Free Plating TL082L-D08-T TL082L-P08-R TL082L-S08-R Halogen Free TL082G-D08-T TL082G-P08-R TL082G-S08-R Package DIP-8 TSSOP-8 SOP-8 Packing Tube Tape Reel Tape Reel www.unisonic.com.tw Copyright © 2009 Unisonic Technologies Co., Ltd 1 of 9 QW-R105-019,G TL082 PIN CONFIGURATION LINEAR INTEGRATED CIRCUIT UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 2 of 9 QW-R105-019,G TL082 BLOCK DIAGRAM LINEAR INTEGRATED CIRCUIT UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 3 of 9 QW-R105-019,G TL082 ABSOLUTE MAXIMUM RATING (Ta=25°C) LINEAR INTEGRATED CIRCUIT PARAMETER SYMBOL RATINGS UNIT Supply Voltage (Note 2) VCC ±18 V Input Voltage (Note 3) VIN ±15 V Differential Input Voltage (Note 4) VID ±30 V Power Dissipation PD 680 mW Output Short-Circuit Duration (Note 5) Infinite Operating Temperature TOPR -20 ~ +85 °C Storage Temperature Range TSTG -65 ~ +150 °C Note: 1. Absolute maximum ratings are those values beyond which the device could be permanently damaged. Absolute maximum ratings are stress ratings only and functional device operation is not implied. 2. All voltage values, except differential voltage, are with respect to the zero reference level (ground) of the supply voltages where the zero reference level is the midpoint between VCC- and VCC+. 3. The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 volts, whichever is less. 4. Differential voltages are at the non-inverting input terminal with respect to the inverting input terminal. 5. The output may be shorted to ground or to either supply. Temperature and/or supply voltages must be limited to ensure that the dissipation rating is not exceeded. THERMAL DATA PARAMETER Junction to Ambient SOP-8 DIP-8 TSSOP-8 SOP-8 DIP-8 TSSOP-8 SYMBOL θJA RATINGS 125 85 120 40 41 37 UNIT °C/W °C/W °C/W °C/W °C/W °C/W Junction to Case θJC ELECTRICAL CHARACTERISTICS ( VCC=±15V, Ta=25°C, TMIN=0°C, TMAX=70°C , unless otherwise specified) PARAMETER SYMBOL TEST CONDITIONS Ta=25°C Input Offset Voltage (RS=50Ω) VIO TMIN ≤Ta ≤TMAX Input Offset Voltage Drift DVIO Ta=25°C Input Offset Current (Note) IIO TMIN ≤Ta ≤TMAX Ta=25°C Input Bias Current (Note) IIB TMIN ≤Ta ≤TMAX Input Common Mode Voltage Range VICM Ta=25°C, RL=2kΩ, Ta=25°C, RL=10kΩ Output Voltage Swing ±VOPP TMIN ≤Ta ≤TMAX, RL=2kΩ TMIN ≤Ta≤ TMAX, RL=10kΩ Large Signal Voltage Gain Ta=25°C Avd (RL=2kΩ, VOUT=±10V) TMIN ≤Ta ≤TMAX VIN=10mV, RL=2kΩ, CL=100pF, Gain Bandwidth Product (Ta=25°C) GBP f=100kHZ Input Resistance RI Common Mode Rejection Ratio Ta=25°C CMR (RS=50Ω) TMIN ≤Ta ≤TMAX Supply Voltage Rejection Ratio Ta=25°C SVR (RS=50Ω) TMIN ≤Ta ≤TMAX MIN TYP 3 10 5 20 ±11 10 12 10 12 25 15 2.5 70 70 70 70 -12~+15 12 13.5 MAX 10 13 100 10 400 20 UNIT mV µV/°C pA nA pA nA V V V V V V/mV MHz Ω dB dB 200 4 1012 86 86 UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 4 of 9 QW-R105-019,G TL082 ELECTRICAL CHARACTERISTICS (Cont.) PARAMETER Supply Current, No Load Channel Separation (Av=100, Ta=25°C) Output Short-Circuit Current Slew Rate (Ta=25°C) Rise Time (Ta=25°C) Overshoot (Ta=25°C) Total Harmonic Distortion (Ta=25°C) LINEAR INTEGRATED CIRCUIT SYMBOL TEST CONDITIONS ICC Ta=25°C V01/V02 IOS SR tR KOV THD Ta=25°C TMIN ≤Ta ≤TMAX VIN=10V, RL=2kΩ CL=100pF, unity gain VIN =20mV, RL=2kΩ CL=100pF, unity gain VIN=20mV, RL=2kΩ CL=100pF, unity gain AV=20dB, f=1kHz, RL=2kΩ, CL=100pF, VOUT=2Vpp) 10 10 8 MIN TYP 3.6 120 40 16 0.1 10 0.01 60 60 MAX 5.6 UNIT mA dB mA mA V/µs µs % % Phase Margin Φm 45 Degrees nV Equivalent Input Noise Voltage eN 15 (RS=100Ω, f=1KHz) Hz Note: The Input bias currents are junction leakage currents, which approximately double for every 10°C increase in the junction temperature. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 5 of 9 QW-R105-019,G TL082 PARAMETER MEASUREMENT INFORMATION LINEAR INTEGRATED CIRCUIT UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 6 of 9 QW-R105-019,G TL082 TYPICAL APPLICATION CIRCUIT 100 KHz Quadruple Oscillators LINEAR INTEGRATED CIRCUIT UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 7 of 9 QW-R105-019,G TL082 TYPICAL CHARACTERISTICS LINEAR INTEGRATED CIRCUIT Supply Current (mA) UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 8 of 9 QW-R105-019,G TL082 LINEAR INTEGRATED CIRCUIT UTC assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all UTC products described or contained herein. UTC products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 9 of 9 QW-R105-019,G