UAC3092AL-S20-R

UNISONIC TECHNOLOGIES CO., LTD UAC3092A ALTERNATOR VOLTAGE REGULATOR DESCRIPTION The UTC UAC3092A is designed for Load Response Control and voltage regulation of diode rectified alternator charging systems for automotive applications. LINEAR INTEGRATED CIRCUIT FEATURES * Forced load response control (LRC) with heavy load transitions at low RPM * Voltage regulated to ± 0.1V @ 25°C * External resistor adjustable operating frequency * Regulation is effective with loads as high as 1.0A * Load dump protection of lamp, field control devices, and loads * Undervoltage, overvoltage , phase fault (broken belt) detection and duty cycle limited protections SOP-20 *Pb-free plating product number: UAC3092AL ORDERING INFORMATION Order Number Normal Lead Free Plating UAC3092A-S20-R UAC3092AL-S20-R UAC3092A-S20-T UAC3092AL-S20-T Package SOP-20 SOP-20 Packing Tape Reel Tube UAC3092AL-S20-R (1)Packing Type (2)Package Type (3)Lead Plating (1) R: Tape Reel, T: Tube (2) S20: SOP-20 (3) L: Lead Free Plating, Blank: Pb/Sn www.unisonic.com.tw Copyright © 2006 Unisonic Technologies Co., Ltd 1 of 5 QW-R121-005,B UAC3092A PIN CONFIGURATION LINEAR INTEGRATED CIRCUIT Filter Buffer Remote Sense Lamp Collector Lamp Base Gnd Oscillato Adjust VREFΦ Oscillator 1 2 3 4 5 6 7 8 9 20 VREF 19 Undervoltage 18 17 16 15 14 13 12 11 Source Gate NC Gnd Vcc1 Vcc3 Supply Regulation Rate Phase 10 PIN DESCRIPTION DESCRIPTION This pin provides Sense input or the Supply Regulation input. The Sense input is input for the true battery voltage. This pin connects to drive the fault lamp. It is also used to sense a closed ignition 3 switch (voltage sense). 4 This pin provides base current to the fault lamp drive transistor (Q2). 5 This pin is for Ground return for the fault lamp control logic circuit. 6 IC ground 7 Connected to a resistor to ground that adjusts the internal oscillator frequency 8 This is a pin for the 1.1 V ~ 1.4 V reference voltage test. 9 This is a pin for checking the operation of the internal oscillator. The Phase input detects the existence of a magnetic field rotating within the 10 Phase alternator. The Rate pin is Load Response Control recovery rate selector pin used to select a 11 Rate slow mode (floating) or fast mode (ground). The Supply Regulation pin is used as a representation of the alternator output 12 Supply Regulation voltage. This input also used to monitor overvoltage or load dump conditions. 13 Vcc3 Voltage supply for the internal Charge Pump. 14 Vcc1 Voltage supply for the entire IC except for the Charge Pump. 15 Ground Ground for the IC. 16 N/C No connection. 17 Gate The Gate Controls of the MOSFET used to energize the field winding. 18 Source MOSFET source reference for Field winding control. If this pin have voltage goes below 1.0 V, the fault lamp is turn on. The IC will 19 Undervoltage continue to function, but with limited performance. 20 VREF Pin for the Band gap reference voltage 1.7 V ~ 2.3 V. Note: Pin 8, and 20 are test points only PIN NO. 1 2 PIN NAME FB Sense Lamp Collector and Power-Up/Down Lamp Base Ground Ground Oscillator Adjust VREFΦ Oscillator UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 2 of 5 QW-R121-005,B UAC3092A BLOCK DIAGRAM FB UV 1 19 UTC UAC3092 A Lost Sense Circuit 2 Signal Combiner and switch VREF 20 LINEAR INTEGRATED CIRCUIT VREF Φ 8 Bandgap Reference Bias + - Vcc1 14 Power Supply Charge Pump Vcc3 13 17 Gate 18 Undervoltage Sense (Remote) Low Pass filter Buff - Load Dump + Power Up/Down Circuit 3 Source Supply Reg (Local ) 12 X1 + - Overvoltage Lamp coII . + Phase 10 + Counter Regulate Output Control Control Logic Lamp Control Logic 4 Lamp Base 12 DAC Prescaler (24 ) Osc . Adjust 7 Oscillator 9 Oscillator 11 Rate Prescaler (26 ) 4 8 5 Divide By (1/12/48) Up/ Down Counter 4 (2 ) Gnd 6 15 Gnd UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 3 of 5 QW-R121-005,B UAC3092A ABSOLUTE MAXIMUM RATINGS (Ta=25℃) LINEAR INTEGRATED CIRCUIT PARAMETER SYMBOL RATINGS UNIT VBAT 24 Power Supply Voltage 40 V Load Dump Transient Voltage (Note 1) +VMAX -2.5 Negative Voltage (Note 2) -VMIN Power Dissipation (Ta=125℃) PD 867 m/W Operating Junction Temperature TJ +150 ℃ Operating Ambient Temperature Range TOPR -35 ~ +125 ℃ Storage Temperature Range TSTG -45 ~ +150 ℃ Note: 1. 125 ms wide square wave pulse. 2. Maximum time = 2 minutes. 3. Absolute maximum ratings are those values beyond which the device could be permanently damaged. Absolute maximum ratings are stress ratings only and functional device operation is not implied. THERMAL DATA PARAMETER Thermal Resistance, Junction to Ambient SYMBOL θJA RATINGS 75 UNIT °C/W ELECTRICAL CHARACTERISTICS (External components per Figure 1,Ta=25℃, unless otherwise noted.) PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNIT DC CHARACTERISTICS Regulation Voltage VREG Determined by external resistor divider 14.85 V Regulation Voltage Temperature TC -13 -11 -9.0 mV/℃ Coefficient Suggested Battery Voltage VBAT 11.5 14.85 16.5 V Operating Range Power Up/Down Threshold VPWR 0.5 1.2 2.0 V Voltage (Pin 3) IQ1 VBAT=12.8V, Ignition off, Ta=25℃ 1.3 2.0 mA Standby Current IQ2 VBAT=12.8V, Ignition off, -35℃≤Ta≤125℃ 3.0 Zero Temperature Coefficient 1.1 1.25 1.4 V VREFφ Reference Voltage, (Pin 8) Band Gap Reference Voltage VREF 1.7 2.0 2.3 V (Pin 20) Band Gap Reference TC -13 -11 -9.0 mV/℃ Temperature coefficient Sense Loss Threshold (Pin 2) SLOSS (TH) 0.6 1.0 V Phase Detection Threshold PTH 1.0 1.25 1.5 V Voltage (Pin 10) Phase Rotation Detection PROT 36 Hz Frequency (Pin 10) Undervoltage Threshold (Pin 19) UUV 1.0 1.25 1.5 V Overvoltage Threshold VOV Pin 2, or Pin 12 if Pin 2 is not used V 1.09(V ) 1.12(V ) 1.16(V ) Load Dump Threshold VLD Pin 2, or Pin 12 if Pin 2 is not used V 1.33(V ) 1.4(V ) 1.48(V ) REF REF REF REF REF REF UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 4 of 5 QW-R121-005,B UAC3092A ELECTRICAL CHARACTERISTIC(Cont.) PARAMETER SYMBOL SWITCHING CHARACTERISTICS Fundamental Regulation Output f Frequency. (Pin 17) Suggested Clock Oscillator fosc Frequency Range, (Pin 9) Duty Cycle (Pin 17) StartDC At Start-up OVDC During Overvoltage Condition Low/High RPM Transition LRCFreq Frequency (Pin 10) LRCS LRCF LRC Duty Cycle Increase Rate LRCH LINEAR INTEGRATED CIRCUIT TEST CONDITIONS Clock oscillator frequency divided by 4096 Determined by external resistor, RT MIN TYP 68 MAX UNIT Hz 350 31 5.5 309 10.5 42 %/sec 501 kHz % % Hz 205 27 3.5 247 280 29 4.7 273 9.5 38 455 Low RPM Mode(LRCFreq