UM603AL-P08-R

UNISONIC TECHNOLOGIES CO., LTD UM603/A DUAL OPERATIONAL AMPLIFIER AND CURRENT CONTROLLER DESCRIPTION The UTC UM603/A is a monolithic IC that includes one independent op-amp and another op-amp for witch the non inverting input is wired to a 2.5V fixed voltage reference. This device is offering space and cost saving in many applications like power supply management or data acquisition systems LINEAR INTEGRATED CIRCUIT FEATURES OPERATIONAL AMPLIFIER *Low input offset voltage: 0.5mV typ. for UTC UM603A *Low supply current: 350uA/op.(@ VCC= 5 V) *Medium bandwidth(unity gain): 0.9MHz *Large output voltage swing: 0 V ~ (VCC-1.5 V) *Input common mode voltage range includes ground *Wide power supply range: 3V ~ 32V ±1.5 ~ ±16V VOLTAGE REFERENCE *Fixed output voltage reference 2.5V *±0.4% and ±1% voltage precision *Sink current capability : 1 ~ 100mA *Typical output impedance : 0.2Ω Lead-free: UM603L/UM603AL Halogen-free: UM603G/UM603AG ORDERING INFORMATION Normal UM603-P08-R UM603-S08-R UM603A-P08-R UM603A-S08-R Ordering Number Lead Free UM603L-P08-R UM603L-S08-R UM603AL-P08-R UM603AL-S08-R Halogen Free UM603G-P08-R UM603G-S08-R UM603AG-P08-R UM603AG-S08-R Package TSSOP-8 SOP-8 TSSOP-8 SOP-8 Packing Tape Reel Tape Reel Tape Reel Tape Reel UM603L-P08-R (1)Packing Type (2)Package Type (3)Lead Plating (1) R: Tape Reel (2) P08: TSSOP-8, S08: SOP-8 (3) G: Halogen Free, L: Lead Free, Blank: Pb/Sn www.unisonic.com.tw Copyright © 2009 Unisonic Technologies Co., Ltd 1 of 6 QW-R105-031.D UM603/A PIN CONFIGURATION LINEAR INTEGRATED CIRCUIT PIN DESCRIPTION PIN NO 1 2 3 4 5 6 7 8 PIN NAME Output 1 Inverting Input1 Non-Inverting Input1 VCCNon-Inverting Input2 Inverting Input2 Output 2 VCC+ I/O O I O I I O PIN DESCRIPTION OP1 output OP1 inverting input A 2.5V fixed voltage reference output, wired to OP1 non-inverting input OP2 non-inverting input OP2 inverting input OP2 output UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 2 of 6 QW-R105-031.D UM603/A ABSOLUTE MAXIMUM RATINGS LINEAR INTEGRATED CIRCUIT PARAMETER SYMBOL RATING UNIT Supply Voltage VCC 36 V Differential Input Voltage VI(DIFF) 36 V Input Voltage VIN -0.3 ~ +36 V Junction Temperature TJ +125 °C Operating Temperature TOPR -55 ~ +125 °C Note: Absolute maximum ratings are those values beyond which the device could be permanently damaged. Absolute maximum ratings are stress ratings only and functional device operation is not implied. THERMAL DATA PARAMETER Thermal Resistance Junction to Ambient SOP-8 TSSOP-8 SYMBOL θJA RATING 175 120 UNIT °C/W ELECTRICAL CHARACTERISTICS PARAMETER Total Supply Current, excluding Current in the Voltage Reference SYMBOL ICC TEST CONDITIONS VCC+=5V, no load, TMIN≤Ta≤TMAX VCC+=30V, no load, TMIN≤Ta≤TMAX MIN 0.7 TYP. MAX 1.2 2 UNIT mA VCC+=+5V, VCC=Ground, Ta=25°C (unless otherwise specified) PARAMETER SYMBOL TEST CONDITIONS OPERATOR1 (op-amp with non-inverting input connected to the internal VREF) VI(CM)=0V Ta=25°C UM603A TMIN≤Ta≤TMAX Input Offset Voltage VI(OFF) VI(CM)=0V UM603 Ta=25°C TMIN≤Ta≤TMAX Input Offset Voltage Drift DVI(OFF) Input Bias Current II(BIAS) negative input VI(CM)=0V Large Signal Voltage Gain Avd VCC=15V, RL=2k Vi(CM)=0V Supply Voltage Rejection Ratio SVR VCC=5V ~30V VOUT=2V Output Current Source ISOURCE VCC=+15V, Vid=+1V VCC =+15V Short Circuit to Ground ISC Vid=-1V, Output Current Sink ISINK VCC=+15V, VOUT=2V VCC+=30V High Level Output Voltage VOH Ta=25℃, RL=10k TMIN≤Ta≤TMAX RL=10k Low Level Output Voltage VOL TMIN≤Ta≤TMAX VIN=0.5 ~ 3V, VCC=15V Slew Rate at Unity Gain SR RL=2k, CL=100pF, unity gain VCC=30V, RL=2K, CL=100pF Gain Bandwidth Product GBP f=100kHz, VIN=10mV f=1kHz Total Harmonic Distortion THD Av=20dB, RL=2k, VCC=30V CL=100pF, VOUT=2VPP MIN TYP MAX UNIT 0.5 2 3 4 5 mV 1 7 20 100 65 20 100 40 40 20 mV μV/°C nA V/mV dB mA 60 mA mA V 10 27 27 28 5 20 20 mV V/μs MHz % 0.2 0.5 0.4 0.9 0.02 UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 3 of 6 QW-R105-031.D UM603/A ELECTRICAL CHARACTERISTICS(Cont.) LINEAR INTEGRATED CIRCUIT VCC+=+5V, VCC=Ground, VOUT=1.4V, Ta=25°C (unless otherwise specified) PARAMETER SYMBOL TEST CONDITIONS OPERATOR2 (independent op-amp)(Note 1) Ta=25°C UM603A TMIN≤Ta≤TMAX Input Offset Voltage VI(OFF) Ta=25°C UM603 TMIN≤Ta≤TMAX Input Offset Voltage Drift DVI(OFF) Input Offset Current Input Bias Current Large Signal Voltage Gain Supply Voltage Rejection Ratio Input Common Mode Voltage Range Common Mode Rejection Ratio Output Current Source Short Circuit to Ground Output Current Sink High Level Output Voltage Low Level Output Voltage Slew Rate at Unity Gain Gain Bandwidth Product Total Harmonic Distortion II(OFF) II(BIAS) Avd SVRR VI(CM) CMRR IO(SOURCE) ISC IO(SINK) VOH VOL SR GBP THD TMIN≤Ta≤TMAX MIN TYP 0.5 1 7 2 20 MAX 2 3 4 5 30 50 150 200 UNIT mV mV μV/°C nA nA V/mV dB TMIN≤Ta≤TMAX VCC=15V, RL=2k, VOUT=1.4V~11.4V TMIN≤Ta≤TMAX VCC=5V ~30V VCC=+30V (Note 1) TMIN≤Ta≤TMAX TMIN≤Ta≤TMAX VCC=+15V, VOUT=2V, Vjd=+1V VCC=+15V Vid=-1V, VCC=+15V, VOUT=2V VCC+=30V Ta=25℃, RL=10k TMIN≤Ta≤TMAX RL=10k TMIN≤Ta≤TMAX VIN=0.5 ~ 3V, VCC=15V RL=2k, CL=100pF, unity gain VCC=30V, RL=2K, CL=100pF f=100kHz, VIN=10mV f=1kHz Av=20dB, RL=2k, Vcc=30V, CL=100pF, VOUT=2Vpp 50 25 65 0 0 70 60 20 10 27 27 100 100 (VCC+)-1.5 (VCC+)-2 V dB 85 40 40 20 28 5 20 20 60 mA mA mA V mV V/μs MHz % 0.2 0.5 0.4 0.9 0.02 VOLTAGE REFERENCE PARAMETER Cathode Current PARAMETER UM603A Reference Input Voltage UM603 VREF SYMBOL Ik SYMBOL Value 1 ~ 100 TEST CONDITIONS ±0.4%, Ta=25°C TMIN≤Ta≤TMAX, VKA=VREF, IKA=10mA ±1%, Ta=25°C TMIN≤Ta≤TMAX, VKA=VREF, IKA=10mA VKA=VREF; Ik=10mA TMIN≤Ta≤TMAX MIN 2.49 2.48 2.475 2.45 TYP 2.5 2.5 MAX 2.51 2.52 2.525 2.55 UNIT mA UNIT V Reference Input Voltage Deviation △VREF mV Over Temperature Range 7 30 Minimum Cathode Current for IMIN VKA=VREF 0.5 1 mA Regulation Dynamic Impedance(Note 2) ∣ZKA∣ VKA=VREF, △Ik=1~100mA, f