UPS601G-D08-T

UNISONIC TECHNOLOGIES CO., LTD UPS601 HIGH PERFORMANCE CURRENT MODE POWER SWITCH DESCRIPTION The UTC UPS601 is designed to provide several special enhancements to satisfy the needs, for example, Power-Saving mode for low standby power (5V 16 9.9 21 11.2 19 28 4.9 62 135 4.1 5.4 1.7 1.6 1.5 68 74 ±3 V V V kHz kHz % % kHz % % kΩ ms V V V ms °C V V 6.3 0.5 6.7 61 20 68 0 ±1.5 75 40 80 ±4.5 5 5 26 12.6 4.7 55 120 3.9 5.1 5.1 70 150 4.3 5.7 UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 4 of 12 QW-R119-003.G UPS601 ELECTRICAL CHARACTERISTICS(Cont.) LINEAR INTEGRATED CIRCUIT PARAMETER SYMBOL TEST CONDITIONS CURRENT LIMITING SECTION Peak Current Limitation VCS VFB=4.4V Threshold Voltage For IVIN =60μA VSENSE-L IVIN=60μA POWER MOS-TRANSISTOR SECTION Drain-Source Breakdown Voltage VDSS VGS=0V, ID=250μA Turn-on voltage between gate and source VTH VDS=VGS, ID=250μA Drain-Source Diode Continuous Source IS Current Static Drain-Source On-State Resistance RDS(ON) VGS=10V, ID=0.6A VDD =300V, ID =1.2A Rise Time tR RG=50Ω (Note 1,2) Fall Time tF Notes: 1. Pulse Test: Pulse width≤300μs, Duty cycle≤2% 2. Essentially independent of operating temperature MIN TYP 0.86 0.77 MAX 1 UNIT V V V V A Ω ns ns 600 2 4 1.2 9.3 25 25 11.5 60 60 UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 5 of 12 QW-R119-003.G UPS601 FUNCTIONAL DESCRIPTION LINEAR INTEGRATED CIRCUIT The internal reference voltages and bias circuit work at VCC> VTHD (ON), and shutdown at VCCVOVP1) for continual a blanking time. The first OVP function will not inactive after soft-start phase. The second OVP will shutdown the switching of the power MOSFET whenever VCC>VOVP2. The first OVP case as followed FIG.7. The test circuit as followed FIG.9. FIG.6 OLP case FIG.7 OVP case 8 of 12 QW-R119-003.G UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw UPS601 FUNCTIONAL DESCRIPTION(Cont.) LINEAR INTEGRATED CIRCUIT FIG.8 OLP test circuit FIG.9 OVP test circuit OTP OTP will shut down driver when junction temperature TJ>T (THR) for continual a blanking time. (7) Driver Output Section The driver-stage drives the gate of the MOSFET and is optimized to minimize EMI and to provide high circuit efficiency. This is done by reducing the switch on slope when reaching the MOSFET threshold. This is achieved by a slope control of the rising edge at the driver’s output. The output driver is clamped by an internal 15V Zener diode in order to protect power MOSFET transistors against undesirable gate over voltage. (8) Inside power switch MOS transistor Specific power MOS transistor parameter is as “POWER MOS TRANSISTOR SECTION” in electrical characteristics table. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 9 of 12 QW-R119-003.G UPS601 TYPICAL APPLICATION CIRCUIT LINEAR INTEGRATED CIRCUIT FIG.10 UPS601 Typical Application Circuit Table1. Components reference description for UPS601 application circuit DESIGNATOR C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 PART TYPE 6.8μF 0.0022μF 22μF 6.8μF 1000μF 100μF 0.1μF 0.001μF 0.1μF 0.01μF DESIGNATOR R1 R2 R3 R4 R5 R6 R7 R8 R9 R10 R11 R12 R13 PART TYPE 3.4Ω 100KΩ 100Ω 1MΩ 0Ω 15Ω 510Ω 4.7KΩ 1.8KΩ 5.11KΩ 1.5~4MΩ 4.99KΩ 1KΩ DESIGNATOR D1 D2 D3 D4 D5 D6 D7 IC1 IC2 IC3 YC1 T1 L1 L2 LD1 F1 ZNR1 PART TYPE 1N4007 1N4007 1N4007 1N4007 FR107 RS1D SB340 UPS601 PC-817 TL431NSL 0.001μF EE-16 1mH 2uH LED 1A/250V 07D471K UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 10 of 12 QW-R119-003.G UPS601 TYPICAL CHARACTERISTICS Feedback Voltage During Loadjump From 10% Up To 100% Load (VAC=90V) LINEAR INTEGRATED CIRCUIT 12V 10V 8V 6V 4V 2V 0 -2V 12V 10V 8V 6V 4V 2V 0 -2V Feedback Voltage During Loadjump From 10% Up To 100% Load (VAC=264V) 0 2000 Time (400μs/div) Startup With Full Load Condition at VAC=90V, VSS and VOUT 4000 0 2000 Time (400μs/div) Startup With Full Load Condition at VAC=264V, VSS and VOUT 4000 8V 6V 4V 2V 0 4V 2V 0 0 8V 6V 4V VSS 2V 0 4V 2V VSS VOUT 0 50 100 0 VOUT 50 Time (10ms/div) Startup Behavior At Nominal Load Condition VAC=264V 100 Time (10ms/div) Startup Behavior At Nominal Load Condition VAC=90V 8V 6V 4V 2V 0 4V 2V 0 0 8V 6V 4V 2V VSS 0 4V 2V VSS VFB 0 20 40 0 VFB 20 Time (4ms/div) 40 Time (4ms/div) UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 11 of 12 QW-R119-003.G UPS601 TYPICAL CHARACTERISTICS(Cont.) Frequency vs. Output Power 80 0.8 0.7 Frequency(KHz) Input Power (W) 60 0.6 0.5 0.4 0.3 0.2 0.1 0 0 1 2 3456 78 Output Power, POUT(W) 9 10 0 LINEAR INTEGRATED CIRCUIT NO Load Input Power vs. Line Voltage (Normal Mode) Input Power NO Load (PoUT=0W) 40 VAC=90V 20 100 200 250 150 AC Input Voltage, VIN(V) 300 UTC assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all UTC products described or contained herein. UTC products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 12 of 12 QW-R119-003.G