UPS703L-D08-T

UNISONIC TECHNOLOGIES CO., LTD UPS703 HIGH PERFORMANCE CURRENT MODE POWER SWITCH DESCRIPTION The UTC UPS703 is designed for several special enhancements to satisfy the demands, for example, Power-Saving mode for low standby power (5V 16 9.9 21 11.2 19 28 4.9 62 135 4.1 5.4 1.7 1.6 1.5 68 74 ±3 61 20 68 0 ±1.5 75 40 80 ±4.5 5 5 26 12.6 4.7 55 120 3.9 5.1 5.1 70 150 4.3 5.7 UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 4 of 12 QW-R119-015.C UPS703 ELECTRICAL CHARACTERISTICS(Cont.) LINEAR INTEGRATED CIRCUIT PARAMETER SYMBOL TEST CONDITIONS CURRENT LIMITING SECTION Peak Current Limitation VCS VFB=4.4V Threshold Voltage For IVIN =60μA VSENSE-L IVIN=60μA POWER MOS-TRANSISTOR SECTION Drain-Source Breakdown Voltage VDSS VGS=0V, ID=250μA Turn-On Voltage between Gate and Source VTH VDS=VGS, ID=250μA Drain-Source Diode Continuous Source IS Current Static Drain-Source On-State Resistance RDS(ON) VGS=10V,ID=1.5A VDD =30V, ID =1.0A Rise Time tR RG=25Ω (Note 1,2) Fall Time tF Notes: 1. Pulse Test: Pulse width≤300μs, Duty cycle≤2% 2. Essentially independent of operating temperature MIN TYP 0.86 0.77 MAX 1 UNIT V V V V A Ω ns ns 700 2 4 3 2.8 30 30 4 70 70 UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 5 of 12 QW-R119-015.C UPS703 FUNCTIONAL DESCRIPTION LINEAR INTEGRATED CIRCUIT The internal reference voltages and bias circuit work at VCC> VTHD (ON), and shutdown at VCCVOVP1) for continual a blanking time. The first OVP function will not inactive after soft-start phase. The second OVP will shutdown the switching of the power MOSFET whenever VCC>VOVP2. The first OVP case as followed FIG.7. The test circuit as followed FIG.9. FIG.6 OLP case FIG.7 OVP case 8 of 12 QW-R119-015.C UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw UPS703 FUNCTIONAL DESCRIPTION(Cont.) LINEAR INTEGRATED CIRCUIT FIG.8 OLP test circuit FIG.9 OVP test circuit OTP OTP will shut down driver when junction temperature TJ>T (THR) for continual a blanking time. (7) Driver Output Section The driver-stage drives the gate of the MOSFET and is optimized to minimize EMI and to provide high circuit efficiency. This is done by reducing the switch on slope when reaching the MOSFET threshold. This is achieved by a slope control of the rising edge at the driver’s output. The output driver is clamped by an internal 15V Zener diode in order to protect power MOSFET transistors against undesirable gate over voltage. (8) Inside power switch MOS transistor Specific power MOS transistor parameter is as “POWER MOS TRANSISTOR SECTION” in ELECTRICAL CHARACTERISTICS table. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 9 of 12 QW-R119-015.C UPS703 TYPICAL APPLICATION CIRCUIT YC3 R8 F1 LINE ZNR1 XC1 R4 R3 NEUT D1 8 1 3 L1 2 44 BD1 3 +1 2 C1 R5 10 T1 1 R2 C2 9 3 4 2 LINEAR INTEGRATED CIRCUIT C8 L2 L3 C10 1 3 2 4 12V/1A 12W GND D2 C4 C5 R13 LD2 C3 R15 IC1 2 VIN 3 VCC DRAIN 1 DRAIN 5 SS GND 4 FB 8 6 D3 7 6 R9 R14 R6 R12 R7 IC2 4 3 1 2 CS 7 C9 R10 C6 R1 C7 IC3 R11 FIG.10 UPS703 Typical Application Circuit Table1. Components reference description for UPS703 application circuit DESIGNATOR C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 PART TYPE 22μF 102P 22μF 470μF 470μF 104P 103P 102 104 220μF DESIGNATOR PART TYPE R1 1.3Ω R2 68KΩ R3 2.2MΩ R4 2.2MΩ R5 1MΩ R6 0Ω R7 0Ω R8 15Ω R9 560Ω R10 1KΩ R11 3.9KΩ R12 15KΩ R13 5.1KΩ R14 1.8KΩ R15 1.5MΩ~4.0 MΩ DESIGNATOR D1 D2 D3 IC1 IC2 IC3 T1 L1 L2 L3 LD2 F1 ZNR1 XC1 BD1 YC3 PART TYPE FR107 SB3100 US1D UPS703 PC-817 TL431 EE22 UU9.8 2μH Ring Choke LED 1.0A/250V 7D471K 154P/275V B6S 222 UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 10 of 12 QW-R119-015.C UPS703 TYPICAL CHARACTERISTICS Feedback Voltage During Loadjump From 10% Up To 100% Load (VAC=90V) LINEAR INTEGRATED CIRCUIT 12V 10V 8V 6V 4V 2V 0 -2V 12V 10V 8V 6V 4V 2V 0 -2V Feedback Voltage During Loadjump From 10% Up To 100% Load (VAC=264V) 0 2000 Time (400μs/div) Startup With Full Load Condition at VAC=90V, VSS and VOUT 4000 0 2000 Time (400μs/div) Startup With Full Load Condition at VAC=264V, VSS and VOUT 4000 8V 6V 4V 2V 0 10V 5V 0 0 8V 6V 4V VSS 2V 0 10V VSS VOUT 5V 0 100 0 VOUT 50 Time (10ms/div) Startup Behavior At Nominal Load Condition VAC=90V 50 Time (10ms/div) Startup Behavior At Nominal Load Condition VAC=264V 100 8V 6V 4V 2V 0 4V 2V 0 0 8V 6V 4V VSS 2V 0 4V 2V VFB 0 40 0 20 Time (4ms/div) 40 11 of 12 QW-R119-015.C 20 Time (4ms/div) UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw UPS703 TYPICAL CHARACTERISTICS(Cont.) LINEAR INTEGRATED CIRCUIT Frequency(KHz) UTC assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all UTC products described or contained herein. UTC products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw Input Power (W) 12 of 12 QW-R119-015.C