FX-4011-EAH

Frequency Controlled Crystal Oscillator FX-501 Features Surface Mount Package Reflow Process Compatible Low Phase Noise Build in PPL-Circuit Typical Applications Base Stations Test Equipment Messurement Previous Vectron Model Number Output Frequency Range Standard Frequencies C3310 10 MHz – 160 MHz 10; 25; 26; 39.3216; 52; 56; 61.44;77.76; 104 MHz 122.88; 153.6; 155.52; 160 MHz Reference Frequency Parameter Input frequency Signal Reference Level Reference Input Impedance Min 2 Typ HCMOS Max 100 4 Units MHz Vpp kΩ Condition ± 2 ppm HCMOS / similar sinewave 0.5 2 Output Frequency Parameter Output frequency Signal Load Rise and Fall time Duty cycle 40 15.0 5 60 Min 10 Typ HCMOS Max 160 Units MHz Condition pF ns % @ 15 pF 10 to 90 % @ Vs/2 htttp://www.vectron.com Vectron International•267 LowellRoad, Hudson, New Hampshire 03051•Tel:+1-88-VECTRON-1 Vectron International GmbH & Co. KG • Landstraße, 74924 Neckarbischofsheim, Germany • Tel: +49 7268 801 100 FX-501 page: 1/5 Supply Voltage (Vs) Parameter Supply voltage [Standard] Current consumption Min 3.135 Typ 3.3 Max 3.465 50 Units VDC mA Condition steady state @ +25°C & 3.3VDC Additional Parameters Parameter Phase Noise 3 Min Typ -90 -110 -131 -148 -156 -157 Max Units dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz ps RMS 10 100 1 10 100 1 Condition Hz Hz kHz kHz kHz MHz @ 10Hz .. 150kHz @ 122,88 MHz HCMOS Jitter Weight Processing & Packing Operating temperature range Operable temperature range Storage temperature range -20 -30 -55 0.77 9 Handling & processing note +70 +85 +125 g °C °C °C Typical Phase Noise and Jitter 10 MHz; HCMOS output 122,88MHz; HCMOS output Frequency range [Hz] 10Hz to 100kHz Jitter [ps rms] 0.708ps Frequency range [Hz] 10Hz to 150kHz Jitter [ps rms] 0.755ps htttp://www.vectron.com Vectron International•267 LowellRoad, Hudson, New Hampshire 03051•Tel:+1-88-VECTRON-1 Vectron International GmbH & Co. KG • Landstraße, 74924 Neckarbischofsheim, Germany • Tel: +49 7268 801 100 FX-501 page: 2/5 Enclosure Type G218B Input : Single ended (HCMOS or Sinewave) Output : Single ended HCMOS Height “H” 5.9 Pin Length “L” NA Dimensions : mm Pin Connections 1 2 3 4 5 6 Ref. Frequency in VCXO Control GND RF-OUT Lock Detector Output Vs Description High stable input frequency for syncronisation Test output of the control voltage for the VCXO Only for modul test or observance Ground connection. Keep traces physically short and connect immediately to ground plane for best performance RF syncronised output. Test output signal for PLL lock detected. High signal  PLL in lock Low signal  PLL out of lock Only for modul test or observance Power Supply Pin Marking FX-501 Frequency ● AYYWW Absolute Maximum Ratings Parameter Supply voltage (Vs) Maximum output load @ CMOS Min Typ Max 6.0 40 Units V pF Condition htttp://www.vectron.com Vectron International•267 LowellRoad, Hudson, New Hampshire 03051•Tel:+1-88-VECTRON-1 Vectron International GmbH & Co. KG • Landstraße, 74924 Neckarbischofsheim, Germany • Tel: +49 7268 801 100 FX-501 page: 3/5 Block Diagram VS VS Reference Frequency PLL Circuit 1 4 VCXO Control VS 8 VCXO 5 Loop Filter VCXO 0 VS 8 VCXO 4 5 0 1 0 Lock Detector Standard Shipping Methode A X B P *bei W ≤ 24 mm nur untere Lochreihe ∗by W ≤ 24 mm only lower hole line Lage im Gurt Position in tape Pin 1 Abwickelrichtung Unwinding direction K Gurtunterseite Tape buttom side Gurtoberseite Tape upper side Production tolerance complying DIN IEC 286-3 Enclosure Type G218B Tape width W [mm] tbd Quantity per meter tbd Quantity per reel 850 Dimension P tbd 1 Contact factory for improved stabilities or additional product options. Not all options and codes are available at all frequencies. 2 Unless otherwise stated all values are valid after warm-up time and refer to typical conditions for supply voltage, frequency control voltage, load, temperature (25°C) 3 Phase noise degrades with increasing output frequency. 4 Subject to technical modification. 5 Contact factory for availability. Notes: htttp://www.vectron.com Vectron International•267 LowellRoad, Hudson, New Hampshire 03051•Tel:+1-88-VECTRON-1 Vectron International GmbH & Co. KG • Landstraße, 74924 Neckarbischofsheim, Germany • Tel: +49 7268 801 100 FX-501 page: 4/5 Recommanded Reflow Profile Profile Feature Average ramp-up rate (TL to Tp) Preheat -Temperature Min TSmin -Temperature Min Tsmax -Time (min to max) tS Pb-Free Assembly/ Sn-Pb Assembly 3°C/second max. 150°C 200°C 60-180 seconds 3°C/second max 217°C 60-150 seconds max 260°C Profile Feature Time 25°C to Peak Temperature Time maintainted above -Temperature (TL) -Time (tL) Pb-Free Assembly/ Sn-Pb Assembly 8 minutes max. 217°C 60-150 seconds TSmax to TL-Ramp-up Rate Time maintainted above -Temperature (TL) -Time (tL) Peak Temperature (TP) Time within 5°C of actual Peak Temperature (tP) Ramp-down Rate 20-40 seconds 6°C/ second max Note: All temperatures refer to topside of the package, measured on the package body surface. SMD oscillators must be on the top side of the PCB during the reflow process How to order this product: Use this worksheet to forward the following information to your factory representative: Model FX-401 Height 1 Supply Voltage Code E RF Output Code A Temperature Range J Reference Frequency Output Frequency Height: 1: 5,9 mm Supply Voltage Code: E: 3,3 V RF Output Code: A: HCMOS Temperature Range: H: -30...+85°C J: -20...+70°C htttp://www.vectron.com Vectron International•267 LowellRoad, Hudson, New Hampshire 03051•Tel:+1-88-VECTRON-1 Vectron International GmbH & Co. KG • Landstraße, 74924 Neckarbischofsheim, Germany • Tel: +49 7268 801 100 FX-501 page: 5/5