SO-720-LPD-HDA

SO-720 SAW Based Clock Oscillator Features • Industry Standard Package, 5.0 x 7.5 x 2.0 mm • ASIC Technology For Ultra Low Jitter 0.100 ps-rms typical across 12 kHz to 20 MHz BW 0.120 ps-rms typical across 50 kHz to 80 MHz BW • Output Frequencies from 150 MHz to 800 MHz • 3.3 V Operation • LV-PECL or LVDS Configuration with Fast Transition Times • Complementary Outputs • Output Disable Feature • Improved Temperature Stability over Standard SAW XO Product is free of lead and compliant to EC RoHS Directive Applications Reference Clock for Wired and Wireless Products Description • 1-2-4 Gigabit Fibre Channel • 10 Gigabit Fibre Channel • 10GbE LAN / WAN • OC-192 • SONET / SDH Standard INCITS 352-2002 INCITS 364-2003 IEEE 802.3ae ITU-T G.709 GR-253-CORE Issue3 Description The SO-720 is a SAW Based Clock Oscillator that achieves low phase noise and very low jitter performance. The SO-720 is housed in an industry standard 6-Pad leadless ceramic package that is hermetically sealed. Packaging options include bulk or tape and reel. Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 Page 1 of 7 Tel: 1-88-VECTRON-1 Website: www.vectron.com Rev: 21 Jun 2006 SO-720 SAW Clock Oscillator Electrical Performance Parameter Frequency Nominal Frequency Frequency Stability (Ordering Option) Aging Supply Voltage Current (No Load) Outputs Mid Level - LVPECL Swing – LVPECL Mid Level - LVDS Swing – LVDS Current Rise Time Fall Time Symmetry Jitter (12 kHz – 20 MHz BW) 622.08 MHz Jitter (50 kHz – 80 MHz BW) 622.08 MHz Period Jitter, RMS (622.08 MHz) Period Jitter, Peak - Peak (622.08 MHz) Operating Temp. (Ordering Option) Package Size 1. 2. 3. 4. 5. 6. 7. 8. 9. Symbol fN fSTAB Minimum 150 Typical Maximum 800 Units MHz ppm ppm Notes 1,2 1,2 6,8 ±50, ±100 10 VCC ICC 2.97 3.3 55 Vcc-1.25 600 Vcc-2.3 350 3.63 70 Vcc-1.0 750 VCC-2.5 450 20 500 500 55 0.250 0.300 3.0 24 V mA V mV-pp V mV-pp mA ps ps % ps-rms ps-rms ps-rms ps pk-pk °C mm 2,3 3 2,3 2,3 2,3 2,3 6 5,6 5,6 2,3 6,7 6,7 9 9 1 Vcc-1.4 450 VCC-2.4 250 IOUT tR tF SYM φJ φJ φJ φJ TOP 45 50 0.100 0.120 2.5 16 0/70,-20/70 or -40/85 5.0 x 7.5 x 2.0 See Standard Frequencies and Ordering Information (Pg 7). Parameters are tested with production test circuit below (Fig 1). Parameters are tested at ambient temperature with test limits guard-banded for specified operating temperature. Measured as the maximum deviation from the best straight-line fit, per MIL-0-55310. Measured from 20% to 80% of a full output swing (Fig 2). Not tested in production, guaranteed by design, verified at qualification. Integrated across stated bandwidth per GR-253-CORE Issue3. Aging Rate for 10 years (Aging is not part of overall frequency stability budget unless specified at time of order) Broadband Period Jitter measured using Lecroy Wavemaster 8600A 6 GHz Oscilloscope, 250K samples taken. Enable, Disable (-1.3V, +2.0V) 1 6 (+2.0V) tR No connect 2 5 COutput tF SYM = 100 x tA / tB Vcc - 1.0V 80% (-1.3V) 3 4 50Ω Output Vcc - 1.3V 20% Vcc - 1.6V 50Ω Test Circuit Notes: 1) To Permit 50Ω Measurement of Outputs, all DC Inputs are Biased Down 1.3V. 2) All Voltage Sources Contain Bypass Capacitors to Minimize Supply Noise. 3) 50Ω Terminations are Within Test Equipment. tA tB Figure 1. Test Circuit Figure 2. 10K LV-PECL Waveform Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 Page 2 of 7 Tel: 1-88-VECTRON-1 Website: www.vectron.com Rev: 21 Jun 2006 SO-720 SAW Clock Oscillator Outline Diagram Suggested Pad Layout 1.96 [0.077] 3.66 [0.144] 1.78 [0.070] 2.54 [0.100] 5.08 [0.200] mm [inch] Pin Out Pin 1 Symbol NC or OE1 OE1 or NC GND Output COutput VCC Function NC or Enable = LV-CMOS Logic 0 or Ground Disabled = LV-CMOS Logic 1 NC or Enable = LV-CMOS Logic 0 or Ground Disabled = LV-CMOS Logic 1 Case and Electrical Ground Output Complementary Output Power Supply Voltage (+3.3V ± 10%) 2 3 4 5 6 Note 1: For proper operation, chosen disable pin can not be left floating and a pin 1 or pin 2 enable option must be ordered See page 7 for alternative input logic option Tape and Reel (EIA-481-2-A) Po ØDo W2 F W D C N A P1 W1 B Tape Dimensions (mm) Dimension Tolerance SO-720 Reel Dimensions (mm) F Do Typ 1.5 W Typ 16 Po Typ 4 P1 Typ 8 A Typ 178 B Min 1.5 C Typ 13 D Min 20.2 N Min 50 W1 Typ 16.4 W2 Max 22.4 Typ 7.5 # Per Reel 200 Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 Page 3 of 7 Tel: 1-88-VECTRON-1 Website: www.vectron.com Rev: 21 Jun 2006 SO-720 SAW Clock Oscillator Absolute Maximum Ratings Parameter Power Supply Output Current Storage Temperature Soldering Temp/Time Symbol VCC Iout TS TLS Ratings 0 to 4 25 -55 to 125 260 / 40 Unit V mA °C °C/sec Stresses in excess of the absolute maximum ratings can permanently damage the device. Functional operation is not implied at these or any other conditions in excess of conditions represented in the operational sections of this datasheet. Exposure to absolute maximum ratings for extended periods may adversely affect device reliability. Permanent damage is also possible if OD is applied before Vcc. Suggested Output Load Configurations +3.3V 0.10 µF 0.01 µF 0.10 µF 0.01 µF +3.3V +3.3V 150Ω 150Ω OD N/C Gnd 1 2 3 6 5 4 Vcc COutput Output Z = 50Ω Z = 50Ω 100Ω OD N/C Gnd 1 2 3 6 5 4 Vcc COutput Output Z = 50Ω Z = 50Ω 40Ω 40Ω 49Ω 49Ω 240Ω 240Ω LV-PECL to LV-PECL: For short transmission lengths, the power consumption could be reduced by removing the 100 Ω resistor and doubling the value of the pull down resistors. LV-PECL to LVDS: Restricted for short transmission lengths. Configuration may require modification depending on LVDS receiver. +3.3V 0.10 µF 0.01 µF 0.10 µF 0.01 µF +2.0V OD N/C Gnd 1 2 3 6 5 4 Vcc COutput Output 0.01 µF 0.01 µF OD N/C -1.3V 1 2 3 6 5 4 Vcc COutput Output 240Ω 240Ω Functional Test: Allows standard power supply configuration. Since AC coupled, the LV-PECL levels cannot be measured. Production Test: Allows direct DC coupling into 50Ω measurement equipment. Must bias the power supplys as shown. Similar to Figure 1. Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 Page 4 of 7 Tel: 1-88-VECTRON-1 Website: www.vectron.com Rev: 21 Jun 2006 SO-720 SAW Clock Oscillator Typical Phase Noise 0 SO-720-LFF-GAA- 622.0800 MHz -10 -20 -30 -40 Phase Noise Level (dBc/Hz) -50 -60 -70 -80 -90 -100 -110 -120 -130 -140 -150 -160 10 100 1000 10000 100000 1000000 10000000 100000000 Frequency Offset (Hz) Jitter OC48 (12kHz to 20MHz) 0.08 ps-rms or 0.56 ps-pp Jitter OC192 (50kHz to 80MHz) 0.11 ps-rms or 0.80 pp-rms Phase Noise at Specific Frequency Offsets 10Hz -46 dBc/Hz 100Hz -80 dBc/Hz 1000Hz -110 dBc/Hz 10kHz -130 dBc/Hz 100kHz -134 dBc/Hz 1MHz -138 dBc/Hz 10MHz -147 dBc/Hz 20MHz -147 dBc/Hz 40MHz -148 dBc/Hz Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 Page 5 of 7 Tel: 1-88-VECTRON-1 Website: www.vectron.com Rev: 21 Jun 2006 SO-720 SAW Clock Oscillator Reliability VI qualification includes aging at various extreme temperatures, shock and vibration, temperature cycling, and IR reflow simulation. The SO-720 family is capable of meeting the following qualification tests: Environmental Compliance Parameter Mechanical Shock Mechanical Vibration Solderability Gross and Fine Leak Resistance to Solvents Conditions MIL-STD-883, Method 2002 MIL-STD-883, Method 2007 MIL-STD-883, Method 2003 MIL-STD-883, Method 1014 MIL-STD-883, Method 2016 Handling Precautions Although ESD protection circuitry has been designed into the SO-720 proper precautions should be taken when handling and mounting. VI employs a Human Body model (HBM) and a Man-Man model (MM) for ESD susceptibility testing and design protection evaluation. ESD Ratings Model Human Body Model Man Man Model Minimum 1500 V 200 V Conditions MIL-STD 883, Method 3015 V/JESD22-A115-A, Reflow Profile (IPC/JEDEC J-STD-020) Parameter PreHeat Time Ramp Up Time Above 217 oC Time To Peak Temperature Time At 260 oC Ramp Down Symbol tS R UP tL t AMB-P tP R DN Value 60 sec Min, 180 sec Max 3 oC/sec Max 60 sec Min, 150 sec Max 480 sec Max 20 sec Min, 40 sec Max 6 oC/sec Max tL R UP tP R DN 260 Temperature (DegC) The device is designed to meet the JEDEC standard for Pb-Free assembly. The temperatures and time intervals listed are based on the Pb-Free small body requirements. The SO-720 device is hermetically sealed so an aqueous wash is not an issue. Termination Plating: Electroless Gold Plate over Nickel Plate 217 200 150 tS t AMB-P 25 Time (sec) Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 Page 6 of 7 Tel: 1-88-VECTRON-1 Website: www.vectron.com Rev: 21 Jun 2006 SO-720 SAW Clock Oscillator Standard Output Frequencies (MHz) *155.5200 *250.0000 389.6000 600.0000 672.1627 *156.2500 *268.8000 400.0000 622.0800 690.5692 *160.0000 300.0000 480.0000 625.0000 693.4830 *175.0000 311.0400 500.0000 640.0000 704.3806 *187.5000 312.5000 531.2500 644.5313 707.3527 *194.8000 320.0000 532.0000 657.4219 720.0000 *200.0000 350.0000 533.0000 666.5143 768.0000 *240.0000 375.0000 537.6000 669.3266 796.8750 Frequencies not shown are available upon request. *VCC6 is preferred XO for frequencies < 300 MHz Revision Control A 6/21/06 Vectron Prod. Mgt. Release of SO-720 Datasheet Ordering Information SO - 720 - L F F - G A A - xxx.xxx Product Family SO = SO Based XO Frequency 150 - 800 MHz Package 720 = 5.0 x 7.5 x 2.0 mm 6 Pad Ceramic SMD Overall Stability Condition A = Includes 10 years of aging at 40ºC N = Excludes aging Input L = 3.3 Vdc ± 10% Enable/Disable Pin & Input Logic A = Pin 2: Enable Low (or Gnd) / Disable High B = Pin 2: Enable High (or Vcc) / Disable Low C = Pin 1: Enable Low (or Gnd) / Disable High D = Pin 1: Enable High (or Vcc) / Disable Low Output F = LVPECL (45/55% Symmetry) P = LVDS (45/55% Symmetry) Stability G = ± 50 ppm maximum H = ± 100 ppm maximum Operating Temperature C = 0°C to 70°C D = -20ºC to 70ºC F = -40°C to 85°C Not All Combinations Possible For Additional Information, Please Contact: USA: Vectron International, 267 Lowell Rd, Hudson, NH 03051 . . . . Tel: 1-88-VECTRON-1 EUROPE: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tel: +49 (0) 3328-4784-17 ASIA: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tel: +86-21-28909740 Fax: 1-888-FAX-VECTRON Fax: +49 (0) 3328-4784-30 Fax: +86-21-28909240 Vectron International reserves the right to make changes to the product(s) and or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 Page 7 of 7 Tel: 1-88-VECTRON-1 Website: www.vectron.com Rev: 21 Jun 2006