TX-703-0011-12M8

TX-703-0011-12M8 TCXO Nominal frequency (f0) Frequency stabilities Parameter Frequency stability Operating temp. range 12.8 MHz Over all (df/f0) vs. operating temp. range (df/f@25 °C) Additional information ±50ppb vs temp +20..+30°C and aging 24h Parameter -4.6 to 4.6 ppm -0.28 to 0.28 ppm -20 ... 70 °C Value Condition initial tolerance (df/f0) -1 to 1 ppm Holdover 24 h ± 0.32 ppm overall incl.: initial, temp.-20..+70°C, supply, load var. and aging 20 years @25 °C incl. temp. stab. -20...+70°C RF output Parameter Value Condition Signal Load Fan out Rise Time Fall Time Duty cycle V Low V High Enable function LVCMOS 15 pF ±10 % 3 < 8 ns < 8 ns 45 / 55 % x < 0.33 V x > 2.97 V Enable Function Pin 1 high open low @ 10 to 90 %Vout @ 90 to 10 %Vout @ 1.65 V output Pin 3 data data no data Supply voltage Parameter Value Condition Supply voltage (Vs) Current consumption steady state 3.3 V ± 5 % < 4 mA @ Vsnom & 25 °C Additional Parameters Parameter Typ. Max. Condition Phase Noise -90 -115 -127 -137 -140 Value dBc/Hz@10Hz dBc/Hz@100Hz dBc/Hz@1000Hz dBc/Hz@10kHz dBc/Hz@100kHz Condition Parameter Additional information This SMD oscillator is designed only for pick and place/reflow soldering process. Manual soldering may damage the part and therefore not recommended for the mounting of this oscillator. Processing & Packing handling&processing note Additional environmental conditions Vibration IEC 60068-2-6, Test Fc Shock IEC 60068-2-27, Test Ea Sealing test A nicht dicht (not hermetically sealed) Solderability DIN IEC 68 T2-20 (Ta) 100% RoHS 6 compliant Solvent resistance EN 60068-2-45, Test xA washable device Vectron International • Product Specifications TX-703-0011 www.vectron.com modified 2011-03-09 Index : 2 printed 2011-06-03 • page 1 of 4 TX-703-0011-12M8 TCXO Absolute Maximum Ratings Parameter Min Typ Max Units Condition Operable temperature range Storage temperature range -40 -55 85 125 °C °C Enclosure Type G298 Height 1.8 mm all units in mm Pin Connections Pin 1: Tristate control Pin 2: GND (Case) Pin 3: RF-Output Pin 4: Vs (supply voltage) Marking TX-0011 12M800 *VAYYWW * pin-1 marking Vectron International • Product Specifications TX-703-0011 www.vectron.com modified 2011-03-09 Index : 2 printed 2011-06-03 • page 2 of 4 TX-703-0011-12M8 TCXO Reflow profile Profile Feature Pb-Free Assembly/Sn-Pb Assembly Average ramp-up rate (TL to Tp) 3°C/second max. Preheat -Temperature Min (Tsmin) 150°c -Temperature Min (Tsmax) 200°c -Time (min to max) (ts) 60-180 seconds Tsmax to TL - Ramp-up Rate 3°C/second max. Time maintainted above - Temperature (TL) 217°C - Time (tL) 60-150 seconds Peak Temperature (Tp) max 260°C Time within 5°C of actual Peak Temperature (tp) 20-40 seconds Ramp-down Rate 6°C/second max. Time 25°C to Peak Temperature 8 minutes max. Note: All temperatures refer to topside of the package, measured on the package body surface. Additional Information This SMD oscillator has been designed for pick and place reflow soldering. Vectron International • Product Specifications TX-703-0011 www.vectron.com modified 2011-03-09 Index : 2 printed 2011-06-03 • page 3 of 4 TX-703-0011-12M8 TCXO Standard shipping method Tape width W [mm] Quantity per meter Quantity per reel P [mm] A [mm] B [mm] K [mm] 16 125 750 8 5.4 7.4 2.7 Notes: Unless otherwise stated all values are valid after warm-up time and refer to typical conditions for supply voltage, frequency control voltage, load, temperature (25°C). Subject to technical modification. Vectron International • Product Specifications TX-703-0011 www.vectron.com modified 2011-03-09 Index : 2 printed 2011-06-03 • page 4 of 4