TX-7040-EAE-2872-20M0

TX-7040-EAE-2872-20M0 TCXO Nominal frequency (f0) Frequency stabilities Parameter Frequency stability Operating temp. range 20 MHz Over all (df/f0) vs. operating temp. range (df/f@25 °C) Parameter -4.6 to 4.6 ppm -0.28 to 0.28 ppm Value -40 ... 85 °C Condition initial tolerance (df/f0) -1 to 1 ppm vs. supply voltage change (df/f) -0.2 to 0.2 ppm vs. load change (df/f) -0.2 to 0.2 ppm vs. aging / 20 years (df/f) 3V Enable Function Pin 8 high open low @ 10 to 90 %Vout @ 90 to 10 %Vout @ 1.65 V output Pin 5 data data high tristate Supply voltage Parameter Value Condition Supply voltage (Vs) Current consumption steady state 3.3 V ± 5 % < 6 mA @ Vsnom & 25 °C Additional Parameters Parameter Typ. Max. Condition Phase Noise -90 -115 -137 -148 -155 -155 Value dBc/Hz@10Hz dBc/Hz@100Hz dBc/Hz@1000Hz dBc/Hz@10kHz dBc/Hz@100kHz dBc/Hz@1000kHz Condition Parameter Additional information This SMD oscillator is designed only for pick and place/reflow soldering process. Manual soldering may damage the part and therefore not recommended for the mounting of this oscillator. Processing & Packing handling&processing note Additional environmental conditions Rapid temperature changes MIL-883-1010 Cond B 500 cycles -55/125°C Vibration MIL-STD-883 Meth 2007 Cond A 20G 20-2000Hz 4x in each 3axis 4 min Shock MIL-STD-202 Meth 213 Cond.C 200G 6ms 6 shocks in each direction Solderability J_STD_002B Cond A leaded/ Cond. B SMD 245°C (diving Time 5 ±0,5sec.) Dip+Look with 8h damp pre-treatment: solder wetting >95% Solvent resistance MIL-STD-883 Meth 2015 Solv. 1,3,4 Vectron International • Product Specifications TX-7040-EAE-2872 www.vectron.com modified 2011-06-30 Index : 1 printed 2011-07-01 • page 1 of 5 TX-7040-EAE-2872-20M0 TCXO Additional environmental conditions ESD HBM JESD22-A114-A Class 1 10* 1000V Moisture Sensit. Level 1 JESD22-A113-B RoHS compliance 100% RoHS 6 compliant Washable non-washable device Absolute Maximum Ratings Parameter Min Typ Max Units Condition Supply voltage (Vs) Operable temperature range Storage temperature range -40 -55 6 85 125 V °C °C Vectron International • Product Specifications TX-7040-EAE-2872 www.vectron.com modified 2011-06-30 Index : 1 printed 2011-07-01 • page 2 of 5 TX-7040-EAE-2872-20M0 TCXO Enclosure Type G290 Height 1.8 mm all units in mm Pin Connections Pin 1: I.C. Pin 3: I.C. Pin 5: RF-Output Pin 7: N.C. Pin 9: V_supply Marking EAE2872 20M000 *VAYYWW * pin-1 marking 2: N.C. 4: GND 6: N.C. 8: Enable 10: N.C. Vectron International • Product Specifications TX-7040-EAE-2872 www.vectron.com modified 2011-06-30 Index : 1 printed 2011-07-01 • page 3 of 5 TX-7040-EAE-2872-20M0 TCXO Reflow profile Profile Feature Pb-Free Assembly/Sn-Pb Assembly Average ramp-up rate (TL to Tp) 3°C/second max. Preheat -Temperature Min (Tsmin) 150°c -Temperature Min (Tsmax) 200°c -Time (min to max) (ts) 60-180 seconds Tsmax to TL - Ramp-up Rate 3°C/second max. Time maintainted above - Temperature (TL) 217°C - Time (tL) 60-150 seconds Peak Temperature (Tp) max 260°C Time within 5°C of actual Peak Temperature (tp) 20-40 seconds Ramp-down Rate 6°C/second max. Time 25°C to Peak Temperature 8 minutes max. Note: All temperatures refer to topside of the package, measured on the package body surface. Additional Information This SMD oscillator has been designed for pick and place reflow soldering. Vectron International • Product Specifications TX-7040-EAE-2872 www.vectron.com modified 2011-06-30 Index : 1 printed 2011-07-01 • page 4 of 5 TX-7040-EAE-2872-20M0 TCXO Standard shipping method Tape width W [mm] Quantity per meter Quantity per reel P [mm] A [mm] B [mm] K [mm] 16 125 750 8 5.4 7.4 2.7 Notes: Unless otherwise stated all values are valid after warm-up time and refer to typical conditions for supply voltage, frequency control voltage, load, temperature (25°C). Subject to technical modification. Vectron International • Product Specifications TX-7040-EAE-2872 www.vectron.com modified 2011-06-30 Index : 1 printed 2011-07-01 • page 5 of 5