VCC6-D

VCC6-D 106M250/212M500 Dual Rate PECL and LVDS Oscillator Features • 3.3V LVPECL or 3.3V LVDS • Output frequency select • Enable/Disable output for test and board debug • Hermetically sealed ceramic SMD package • Excellent Power Supply Noise Rejection • Product is compliant to RoHS directive and fully compatible with lead free assembly The VCC6-D Crystal Oscillator Applications • 1Gbps, 2Gbps, 4 Gbps Fiber Channel • Storage Area Network • Host Bus Adapter • RAID controller Description Vectron’s VCC6-D Crystal Oscillator (XO) is quartz stabilized square wave generator with a LV-PECL or LVDS output, operating off a 3.3 volt supply. The VCC6 uses high quality on-chip multiplier to multiply a 26.5625 crystal to either 106M250 or 212M500. Vectron International 267 Lowell Road, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com VCC6-D, Dual Rate 106.250/212.500 LVPECL or LVDS XO Performance Characteristics Table 1. Electrical Performance P arameter Frequency Supply Voltage 1 Supply Current, PECL LVDS Output Logic Levels, 0/70°C PECL Output Logic High2 PECL Output Logic Low2 LVDS Output High Voltage LVDS Output Low Voltage LVDS Differential Output Voltage LVDS Change in Magnitude LVDS Offset Output Voltage LVDS Change in Magnitude of Output Offset Transition Times Rise Time2 Fall Time2 Symmetry or Duty Cycle3 Operating temperature Stability (ordering option)4 RMS Jitter, 12kHz to 20 MHz, fO0.975V, Open) 1 6 (+2V) COutput 2 (- 0.5V) 3 4 50Ω 50Ω 5 Output On Time Period Test Circuit Notes: 1) To Permit 50Ω Measurement of Outputs, all DC Inputs are Biased Down 0.5V. 2) All Voltage Sources Contain Bypass Capacitors to Minimize Supply Noise. 3) 50Ω Terminations are Within Test Equipment. Figure 1. Output Waveform Figure 2. Typical Output Test Conditions (25± 5°C) Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com VCC6-D, Dual Rate 106.250/212.500 LVPECL or LVDS XO Typical Phase Noise at 106.25MHz Typical Phase Noise at 212.50MHz Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com VCC6-D, Dual Rate 106.250/212.500 LVPECL or LVDS XO Outline Diagram and Pin Out Contact pads are gold over nickel Pin # 1 2 3 4 5 6 Symbol E/D FREQ GND fO Cf o V DD Function Output disabled when=logic 0, Output Enabled when=logic1 Device has an internal pull-up resistor. Output=106M25 when = logic 1, 212M50 when = logic 0 Device has as an internal pull-up resistor. Ground Output Frequency Complementary Output Frequency Supply Voltage Tape and Reel J F D A C G B L E I H K Tape and Reel Dimensions (mm) Tape Dimensions Product A B C D E VCC6 12 5.5 1.5 4 8 Reel Dimensions F G H 1.78 20.6 13 I 55 J 6 K 12.4 L 178 # Per Reel 250 Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com VCC6-D, Dual Rate 106.250/212.500 LVPECL or LVDS XO Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can permanently damage the device. Functional operation is not implied at these or any other conditions in excess of conditions represented in the operational sections of this data sheet. Exposure to absolute maximum ratings for extended periods may adversely affect device reliability. Table 2. Absolute Maximum Ratings P arameter Symbol Power Supply VDD Enable/Disable VIN Storage Temperature Tstorage Ratings -0.5 to +5.0 -0.5 to VDD+0.5 -55/125 Unit Vdc Vdc °C Reliability The VCC6 qualification tests will include the following: Table 3. Environnemental Compliance Parameter Mechanical Shock Mechanical Vibration Solderability Gross and Fine Leak Resistance to Solvents Conditions MIL-STD-883 Method 2002 MIL-STD-883 Method 2007 MIL-STD-883 Method 2003 MIL-STD-883 Method 1014 MIL-STD-883 Method 2016 Handling Precautions Although ESD protection circuitry has been designed into the the VCC6, proper precautions should be taken when handling and mounting. VI employs a Human Body Model and a Charged-Device Model (CDM) for ESD susceptibility testing and design protection evaluation. ESD thresholds are dependent on the circuit parameters used to define the model. Although no industry wide standard has been adopted for the CDM, a standard HBM of resistance = 1.5kohms and capacitance = 100pF is widely used and therefore can be used for comparison purposes. Table 4. ESD Ratings M odel Human Body Model Charged Device Model M inimum 1000 1000 Conditions MIL-STD-883 Method 3115 JESD 22-C101 Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com VCC6-D, Dual Rate 106.250/212.500 LVPECL or LVDS XO Suggested IR profile The VCC6 has been qualified to meet the JEDEC standard for Pb-Free assembly. The temperatures and time intervals listed are based on the Pb-Free small body requirements and parameters are listed in Table 7. The VCC6 is hermetically sealed so an aqueous wash is not an issue. Table 7. Reflow Profile P arameter PreHeat Time Ramp Up Time Above 217 oC Time To Peak Temperature Time At 260 oC (max) Time At 240 °C (max) Ramp Down Symbol tS R UP tL t AMB-P tP tp2 R DN Value 60 sec Min, 180 sec Max 3 oC/sec Max 60 sec Min, 150 sec Max 480 sec Max 10 sec Max 60 sec Max 6 oC/sec Max Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com VCC6-D, Dual Rate 106.250/212.500 LVPECL or LVDS XO Frequencies (MHz) which are being developed 106.25/212.50 Other frequencies may be available upon request. Standard frequencies are frequencies which the crystal has been designed and does not imply a stock position. Ordering Information VCC6-Dxx – 106M25 Product Family Crystal Oscillator Supply Voltage, Output D= Dual Rate PECL/LVDS Q: 3.3volt, LVPECL L: 3.3volt, LVDS Frequency MHz example: 106M250= 106.25/212.50MHz Stability Options/Temperature A: +/-100ppm / -10 to 70 C B: +/-50ppm /-10 to 70 C Also available is a VCC6-1091 which is fixed at 212.500MHz, LVPECL, 50ppm over -10 to 70C, and a VCC61121 which is fixed at 212.500MHz, LVPECL and is 100ppm over -10 to 70C. For Additional Information, Please Contact: USA: Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • Fax: 1-888-FAX-VECTRON EUROPE: VI Telefilter · Potsdamer Straße 18, 14513 Teltow, Germany Tel: 49 (0) 3328 4784 17 · Fax: 49 (0) 3328 4784 30 ASIA: Vectron Asia Pacific Sales Office Unit 3119 31st Floor, Jin Mao Tower, 88 Century Boulevard, Shanghai, P.R. China 200120 Tel: +86 21 28909740 / 41 / 42 · Fax: +86 21 28909240 / 2890999 www.vectron.com Vectron International reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. VCC6-D (REVISION DATE: April18 2005) Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com