VCC6-LAE-622M080

VCC6-L 3.3 volt LVDS Oscillator, >270MHz Features • 3.3 V LVDS • Output frequencies from 270-800 MHz • Enable/Disable output for test and board debug • -10/70 or –40/85 °C operating temperature • Hermetically sealed ceramic SMD package • Product is compliant to RoHS directive and fully compatible with lead free assembly The VCC6 Crystal Oscillator Applications • SONET/SDH/DWDM • Ethernet, Gigabit Ethernet • Storage Area Network • Digital Video • Broadband Access Description fo O utput Buffer / Disable fo Vectron’s VCC6 Crystal Oscillator (XO) is quartz stabilized square wave generator with a LVDS output, operating off a 3.3 volt supply. Vectron International 267 Lowell Road, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com VCC6-L Output Frequencies > 270MHz Performance Characteristics Table 1. Electrical Performance P arameter Frequency Supply Voltage 1 Supply Current, Output Enabled Supply Current, Output Disabled Output Logic Levels Output Logic High2 Output Logic Low2 Differential Output Differential Output Error Differential Output Skew Load (differential) Offset Voltage Offset Error Output Leakage Current Transition Times Rise Time2 Fall Time2 Symmetry or Duty Cycle3 Operating temperature (ordering option) Stability (ordering option)4 RMS Jitter, 12kHz to 20 MHz Period RMS Jitter Period P/P Jitter Output Enabled5 Output Disabled5 Output Enable/Disable time Package Size Symbol fO VDD IDD IDD VOH VOL VOD Min 270 3.15 Typical 3.3 M aximum 800 3.45 80 10 1.6 454 50 200 1.375 25 ±10 600 600 55 Units MHz mA uA V V mV mV ps ohms V mV uA ps ps % °C ppm ps ps ps V V nS mm 0.9 247 1.40 1.10 330 VOS VOS 1.125 100 1.25 tR tF SYM 45 50 -10/70 or –40/85 ±25, ±50 or ±100 2 4 30 0.7*VDD 0.3*VDD 400 5.0 x 7.0 x 1.5 1. A 0.01uF and a 0.1uF capacitor should be located as close to the supply as possible (to ground) is recommended. 2. Figure 1 defines these parameters. 3. Symmetry is measured defined as On Time/Period. 4. Includes calibration tolerance, operating temperature, supply voltage variations, aging (40 degreesC/10 years) and shock and vibration (not under operation). 5. Output will be enabled if enable/disable is left open. tR 80 % Vs 20 % tF On Time Period Figure 1. Output Waveform Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com VCC6-L Output Frequencies > 270MHz Outline Diagram, Pad Layout and Pin Out Contact Pad Plating: gold over nickel Table 2. VCC6-LCx Pinout Pin # Symbol 1 2 3 4 5 6 E/D NC GND fO Cf o V DD Function Tristate Function This pin has no internal connection and is floating. Ground Output Frequency Complementary Output Frequency Supply Voltage Table 3. VCC6-LAx Pinout Pin # Symbol 1 2 3 4 5 6 NC ED GND fO Cf o V DD Function This pin has no internal connection and is floating. Tristate Function Ground Output Frequency Complementary Output Frequency Supply Voltage Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com VCC6-L Output Frequencies > 270MHz Tape and Reel J F D A E C G B L I H K Table 4. Tape and Reel Dimensions (mm) Tape Dimensions Product A VCC6 16 B 7.5 C 1.5 D 4 E 8 Reel Dimensions F G H 2 21 13 I 60 J 2 K 17 L 180 # Per Reel 250 Enable/Disable Functional Description Under normal operation the Enable/Disable is left open, or set to a logic high state, and the VCC6 is an oscillation mode with active outputs. When the E/D is set to a logic low, the oscillator stops and the both the output and complementary output are in a high impedance state. This helps facilitate board testing and troubleshooting. Absolute Ratings Stresses in excess of the absolute maximum ratings can permanently damage the device. Functional operation is not implied at these or any other conditions in excess of conditions represented in the operational sections of this data sheet. Exposure to absolute maximum ratings for extended periods may adversely affect device reliability. Table 5. Absolute Maximum Ratings P arameter Symbol Power Supply VDD Enable/Disable VIN Storage Temperature Tstorage Ratings -0.5 to +4.6 -0.5 to VDD+0.5 -55/125 Unit Vdc Vdc °C Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com VCC6-L Output Frequencies > 270MHz Reliability The VCC6 qualification tests include the following: Table 6. Environnemental Compliance P arameter Mechanical Shock Mechanical Vibration Solderability Gross and Fine Leak Resistance to Solvents Moisture Sensitivity Level Conditions MIL-STD-883 Method 2002 MIL-STD-883 Method 2007 MIL-STD-883 Method 2003 MIL-STD-883 Method 1014 MIL-STD-883 Method 2016 MSL1 Handling Precautions Although ESD protection circuitry has been designed into the the VCC6, proper precautions should be taken when handling and mounting. VI employs a Human Body Model and a Charged-Device Model (CDM) for ESD susceptibility testing and design protection evaluation. ESD thresholds are dependent on the circuit parameters used to define the model. Although no industry wide standard has been adopted for the CDM, a standard HBM of resistance = 1.5kohms and capacitance = 100pF is widely used and therefore can be used for comparison purposes. Table 7. ESD Ratings M odel Human Body Model Charged Device Model M inimum 1000 1000 Conditions MIL-STD-883 Method 3115 JESD 22-C101 Suggested IR profile Table 8 shows max temperatures and lower temperatures can also be used e.g. peak temperature of 220C. Termination finish is gold over nickel. The VCC6 is hermetically sealed so an aqueous wash is not an issue. Table 8. Reflow Profile Parameter PreHeat Time Ramp Up Time Above 217 C Time To Peak Temperature Time At 260 oC (max) Ramp Down o Symbol tS R UP tL t AMB-P tP R DN Value 60 sec Min, 180 sec Max 3 oC/sec Max 60 sec Min, 150 sec Max 480 sec Max 15 sec Max 6 oC/sec Max Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com VCC6-L Output Frequencies > 270MHz Frequencies (MHz) 311.040 333.000 500.000 666.5413 700.000 312.500 350.000 600.000 669.3236 779.5686 320.000 400.000 622.080 693.3265 322.2656 446.000 625.000 693.4829 332.000 472.000 644.5313 693.750 Other frequencies may be available upon request. Standard frequencies are frequencies which the crystal has been designed and does not imply a stock position. Ordering Information VCC6-LCB – 622M080 Product Family Crystal Oscillator Output L: LVDS 3.3 Volts Frequency example: 622M080= 622.080 MHz Stability Options/Temperature A: ±100ppm B: ±50ppm Enable/Disable A: E/D is on Pin 2, Pin 2 is a NC C: E/D is on Pin 1, Pin 2 is a NC C: ±100ppm D: ±50ppm E: ±25ppm F: ±25ppm -10 to 70°C -10 to 70°C -40 to 85°C -40 to 85°C -10 to 70°C -40 to 85°C NOTE: Not all combinations are available. A ± 20ppm over -10 to 70°C, +3.3V, E/D on pin 1, VCC6-109-frequency, is available. For Additional Information, Please Contact: USA: Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • Fax: 1-888-FAX-VECTRON EUROPE: Landstrasse, D-74924, Neckarbischofsheim, Germany • Tel: 49 (0) 7268 8010 • Fax: 49 (0) 7268 801281 ASIA: Vectron Asia Pacific Sales 1F~2F. No.8 Workshop No.308 Fenju Rd., WaiGaoQiao Free Trade Zone, Pudong New Area Shanghai, China 200131 •Tel: 8621 50480777 • Fax: 8621 50481881 www.vectron.com Vectron International reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. VCC6-L >270MHz (REVISION DATE: Janaury26, 2007) Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com