VT-701

VT-701 Temperature Compensated Crystal Oscillator Previous Vectron Model VTC2 VT-701 Description Vectron’s VT-701 Temperature Compensated Crystal Oscillator (TCXO) is a quartz stabilized, clipped sine wave output, analog temperature compensated oscillator, operating off either 3.3 or 5.0 volt supply, hermetically sealed 5x7 ceramic package. Features • • • • • • CMOS Output Output Frequencies to 27 MHz Fundamental Crystal Design Optional VCXO Function available Gold over nickel contact pads Hermetically Sealed Ceramic SMD package • • • • • • • • Applications FPGA’s A/D’s, D/A’s Broadband Access Head End Wireless Communications Base Stations Point to point radios Broadband Access Test Equipment • Product is compliant to RoHS directive and fully compatible with lead free assembly Block Diagram VDD Crystal Output Analog Temperature Comp. Vcontrol or NC Gnd Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Page1 Table 1. Electrical Performance Parameter Output Frequency Supply Voltage , Ordering Option Supply Current Operating Temperature, Ordering Option Stability Over TOP, Ordering Option Initial Accuracy, “No Adjust” Option Power Supply Stability Load Stability Aging Pull Range, ordering option Control Voltage to reach Pull Range Control Voltage Impedance Output Level2 Output Logic High Output Logic Low Output Logic High Drive Output Logic Low Drive Output Load Phase Noise, 10.000MHz 10Hz 100Hz 1kHz 10kHz 100kHz Enable Disable3 , Output Enbaled Output Disabled Start Up Time 1. The V-701 power supply pin should be filtered, eg, a 0.1 and 0.01uf capacitor 2. The Output is DC coupled 3. Output is Enabled if E/D is left open VIH VIL 0.3*VDD 2 ms -92 -116 -137 -149 -154 0.7*VDD VOH VOL IOH IOL TPR 0.5 1 0.8*VDD 0.1*VDD -4 4 15 ±5, ±8, ±10, ±12 2.5 1 Symbol fO VDD IDD TOP Min. 5 Typ +3.3 or +5.0 Max 27 10 Units MHz Vdc mA °C ppm ppm ppm ppm ppm/yr ppm V Mohm V V mA mA pF dBc/Hz 0/55, -10/60, -20/70, -30/80, -40/85 ±0.5, ±1.0, ±.5, ±2.0, ±2.5, ±3.0, ±4.0, ±5.0 ±1.0 ±0.3 ±0.2 ±1.0 Outline Drawing 7.0±01 2.0 max 0.4±0.1 Recommended Pad Layout 6.0 1.8 1.4 1.0 5.0±0.1 FREQUENCY Date Code 1.4 1.3 2.54 1.2 1.4 0.8 typ Pad Layout mm Table 2. Pinout 1.27±0.1 1.0±0.1 Pin # 1 2,3,4 Symbol VC NC GND fO NC E/D VDD Function TCXO Control Voltage or Ground Make No Connection Electrical and Lid Ground Output Frequency Make No Connection Enable Disable Supply Voltage 2.54±0.1 0.8±0.1 5 6 7,8 Dimensions in mm 9 10 Page2 1.0±0.1 0.6±0.1 Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Test Circuit tR VOH 50% IC VC 1 + Period 2 15pF VOL On Time tF IDD 4 + VDD .1μF .01μF 3 VCXO Function S VCXO Feature: The VT-701 can be ordered with a VCXO function for applications were it will be used in a PLL, or the output frequency needs fine tune or calibration adjustments. This is a high impedance input , 1Mohm, and can be driven with an op-amp or terminated with adjustable resistors etc. Pin 1 should not be left floating on the VCXO optional device. “No Adjust” Option: In applications were the VT-701 will not be used in a PLL , or the output frequency does not need fine tune adjustments, the best device to use would be a VT-701-xxx-xxx0. By using the “no adjust” option, the circuit is simplified as Vc does not need to be adjusted or set to a predetermined voltage and pin 1 should be grounded (pin 1 can be left open but should not be set to a voltage such as an RF signal or power supply voltage. Maximum Ratings S Absolute Maximum Ratings and Handling Precautions Stresses in excess of the absolute maximum ratings can permanently damage the device. Functional operation is not implied or any other excess of conditions represented in the operational sections of this data sheet. Exposure to absolute maximum ratings for extended periods may adversely affect device reliability. Although ESD protection circuitry has been designed into the VT-701, proper precautions should be taken when handling and mounting, VI employs a Human Body Model and Charged Device Model for ESD susceptibility testing and design evaluation. ESD thresholds are dependent on the circuit parameters used to define the model. Although no industry standard has been adopted for Phase Noise Graph the CDM a standard resistance of 1.5kOhms and capacitance of 100pF is widely used and therefor can be used for comparison purposes. Table 3. Maximum Ratings Parameter Storage Temperature Supply Voltage Control Voltage ESD, Human Body Model ESD, Charged Device Model Symbol TSTORE VDD VC Rating -55/125 6 0/VDD 1500 1000 Unit ºC V V V V Table 4. Environmental Compliance Parameter Mechanical Shock Mechanical Vibration Temperature Cycle Solderability Fine and Gross Leak Resistance to Solvents Moisture Sensitivity Level Contact Pads Condition MIL-STD-883 Method 2002 MIL-STD-883 Method 2007 MIL-STD-883 Method 1010 MIL-STD-883 Method 2003 MIL-STD-883 Method 1014 MIL-STD-883 Method 2015 MSL1 Gold over Nickel Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Page3 IR Reflow S Suggested IR Profile Devices are built using lead free epoxy and can be subjected to standard lead free IR reflow conditions shown in Table 5. Contact pads are gold over nickel and lower maximum temperatures can also be used, such as 220C. Table 5. Reflow Profile Parameter PreHeat Time Ts-min Ts-max Ramp Up Time above 217C Time to Peak Temperature Time at 260C Time at 240C Ramp down Symbol ts Value 200 sec Max 150°C 200°C 3ºC/sec Max 150 sec Max 480 sec Max 10 sec Max 60 sec Max 6ºC/sec Max RUP tL t25C to peak tP tP2 RDN Tape & Reel Table 6. Tape and Reel Information Tape Dimensions (mm) W 16 F 7.5 Do 1.5 Po 4 P1 8 A 180 B 1.5 Reel Dimensions (mm) C 13 D 20.2 N 60 W1 16.4 W2 20.4 #/Reel 1000 Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Page4 Table 7. Standard Frequencies (MHz) 5.000* 19.440 6.400* 19.800 8.192 20.000 10.000 24.000 Standard Frequencies 12.500* 25.000 12.800 26.000 13.000* 27.000 16.384 19.200 20.000 Ordering Information VT-701- E A G - X X X A- xxMxxxxxxx Frequency in MHz Product TCXO Package 5x7 Voltage Options D: +5.0 Vdc ±5%, E: +3.3 Vdc ±5%, Output A: CMOS Temp Range R: 0 /55°C K: -10/60°C J: -20/70°C G: -30/80°C E: -40/85°C Tuning 0: Fixed, No tuning A: ±5ppm B: ±8ppm C: ±10ppm D: ±12ppm Stability 507: ±0.5ppm 106: ±1ppm 156: ±1.5ppm 206: ±2.0ppm 256: ±2.5ppm 306: ±3.0ppm 356: ±3.5ppm 406: ±4.0ppm 506: ±5.0ppm Note: Not all combination of options are available and * notes limited temperature stability. Example: VT-701-EAG-206A-19M2000000 For Additional Information, Please Contact USA: Vectron International 267 Lowell Road Hudson, NH 03051 Tel: 1.888.328.7661 Fax: 1.888.329.8328 Europe: Vectron International Landstrasse, D-74924 Neckarbischofsheim, Germany Tel: +49 (0) 3328.4784.17 Fax: +49 (0) 3328.4784.30 Asia: Vectron International 1F-2F, No 8 Workshop, No 308 Fenju Road WaiGaoQiao Free Trade Zone Pudong, Shanghai, China 200131 Tel: 86.21.5048.0777 Fax: 86.21.5048.1881 Disclaimer Vectron International reserves the right to make changes to the product(s) and or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Rev: 09/03/2009 Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Page5