30721

8 7 6 5 4 3 2 1 REVISIONS VICOR CONFIDENTIAL THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR HEREWITH IS NOT TO BE REPRODUCED, USED OR DISCLOSED IN WHOLE OR IN PART TO ANYONE WITHOUT THE PERMISSION OF VICOR CORP. REV F SEE NOTE 6 #30 DRILL THRU ( .1285 ) (6) PL. DATE DESCRIPTION LEK 11/15/05 1 RELEASED PER E053437 2 DOCUMENT REVISED PER E091418 JS 08/19/09 3 REDRAWN PER E100887 DCS APPROVED EF REJH 6/17/10 KUK .120 (2) PL. .300 (2) PL. E E R.110 MAX (8) PL. 2.22 F 2.000 D D .130 TYP SEE NOTE 5 .11 .410 .650 .49 1.300 2.280 C .40 C -A- .190 .005 .010 MATL TO BE REMOVED .100 B B NOTES: 1. MATERIAL: EXTRUSION SEE SHEET 2 OF 2. 2. REMOVE ALL BURRS AND SHARP EDGES. 3. CLEAR FINISH, RoHS COMPLIANT, CHROMIUM FREE PER CST-0001 LATEST REVISION. " 4. " DENOTES CRITICAL CHARACTERISTIC FOR LOT INSPECTION.' 5. DIMENSIONS APPLIES AT SURFACE -A- (2) PL. 6. MACHINED SURFACE TO BE .010 MAX BELOW SURFACE -A- (6) PL. 7. DIMENSIONS ARE INCHES ONLY. A DRAWN D.P. KELLY MATERIAL SEE NOTES FINISH 09/05 SEE NOTES DO NOT SCALE DRAWING 8 7 6 5 4 3 HS CFG "B" X-FLOW, .4H LOW FLOW, THRU HOLE UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE INCH [MM] TOLERANCES ARE: DECIMALS ANGLES X.XX [X.X] = ±0.01 [0.25] ±1° X.XXX [X.XX] = ±0.005 [0.127] THIRD ANGLE PROJECTION SWD VICOR DATE SIZE CAGE CODE C 67131 SCALE 2 : 1 2 DWG NO A REV 30721 3 SHEET 1 OF 2 1 8 7 6 5 4 3 2 1 REVISIONS VICOR CONFIDENTIAL THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR HEREWITH IS NOT TO BE REPRODUCED, USED OR DISCLOSED IN WHOLE OR IN PART TO ANYONE WITHOUT THE PERMISSION OF VICOR CORP. REV DATE DESCRIPTION APPROVED SEE SHEET 1 OF 2 F F E E 3.00° 1.5 EACH SIDE OF VERT R.035 (24) PL. .014 (2) PL. SEE DETAIL A 1.756 R.035 R.018 (2) PL. .410 D .200 .023 D .036 .235 .110 * .056 (2) PL. R.010 (4) PL. * .058 (8) PL. * .138 (5) PL. * .133 (6) PL. .080 .252 R.030 (8) PL. * .060 (2) PL. * .297 .040 .031 +.020 2.280 - .000 C C * .030 * .060 DETAIL A SCALE 8 : 1 TYP PROFILE COMMON FOR 30722 32173 30721 30184 B B NOTES: 1. MATL: ALUMINUM 6063-T5 2. *DENOTES DIMENSIONS TO THEORETICAL SHARP CORNER 3. ALL DIMENSIONS ARE CRITICAL CHARACTERISTICS. 4. RoHS COMPLIANT PER CST-0001 LATEST REVISION. 5. WORKMANSHIP STANDARDS WS-0004, WS-0006 AND WS-0007 APPLY TO THIS PART. 6. DIMENSIONS ARE INCHES ONLY. DRAWN JSARIPELLA MATERIAL SEE NOTES A FINISH 08/19/09 UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE INCH [MM] TOLERANCES ARE: DECIMALS ANGLES X.XX [X.X] = ±0.01 [0.25] ±1° X.XXX [X.XX] = ±0.005 [0.127] THIRD ANGLE PROJECTION SEE NOTES DO NOT SCALE DRAWING 8 7 6 5 4 3 SWD VICOR DATE HS CFG "B" X-FLOW, .4H, LOW FLOW, THRU HOLE, EXTRUSION SIZE CAGE CODE C 67131 SCALE 4 : 1 2 DWG NO REV 30721 3 SHEET 2 OF 2 1 A